The flash driver for the LPC55S69 is different from
prior LPC family. Move the Flash HAL driver to SoC
specific folder
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This data, placed at physically not existing addresses (0x9xxxxxxx) was used
only by PSoC Programmer and KitProg2 and is no longer needed, but was causing
issues with standard hex file processing tools like srecord (srec_cat).
If the board-specific initialization code configures the serial port to
use an 8-bit divider, the serial_init_clock function would configure the
16-bit divider with the same index instead of the intended 8-bit
divider.
Added WiFi_Bt CM4 PSA target in mbedos json
Added SPE-NSPE mailbox initialization for CM4 SystemInit
Made similar to FUTURE_SEQUANA configurations
Copied FUTURE_SEQUANA CM0 SPM part for WiFi_Bt smoke test
Added CY8CKIT_062_WIFI_BT_M0 and CY8CKIT_062_WIFI_BT_M0_PSA targets
Sorted files for new CY8CKIT_062_WIFI_BT_M0 and CY8CKIT_062_WIFI_BT_M0_PSA targets
Copied files for CY8CKIT_062_WIFI_BT_M0_PSA from FUTURE_SEQUANA
Copied and updated cm0p start files
Corrected according to FUTURE_SEQUANA
Changes to M0 startup files to have SPM started
Fixed implicit declaration warning
Commented interrupts enabling according to FUTURE_SEQUANA flow
Updated prebuild spm_smore CM0 hex for CM4 target
Turned on greentea environment
Used special memory region for common CM0/CM4 data
Updated prebuild CM0 SPM hex
Placed shared memory region for flash operations into SPM shared memory region
Updated cyprotection code and configuration
Start address of protected regions is set by a defined number from target.json
Added masters pcMask configuration
Added support for PSA target to WIFI_BT board
Enabled resources protection for SPM
Aligned RAM usage according to Cypress FlashBoot and CyBootloader
alligned protection config
Added CYW943012P6EVB_01_M0 target
Enlarged heap size, remobed nv_seed
Added heap reservation in linker script from mbed-os
Removed heap size definition
turned on nv_seed config
Removed nv_seed macros
Enabled protection for PSoC6 CM0
Added PSoC6 CM0 PSA readme
Enabled mbed_hal-spm test
Enabled nv_seed and removed unneeded ipc config define
Added SPDX string to feature_ble cypress target files
Removed unneeded supported_toolchains lines for Cypress targets
Disabled protection settings
Corrected flash initialization for PSoC6 CM0 PSA
Changed PSoC6 IPC6 protection for flash
Enabled special flash initialization and enabled protection settings
Updated and added new prebuild PSoC6 CM0 PSA hex files
Disabled HW TRNG and CRC for PSoC6 CM4 PSA target
Added missing const to allow types to match
Updated PSoC6 WIFI_BT_PSA prebuilt directory
Moved PSoC6 shared section usage area definition to begin of ld
Added initial ARM_STD linker and startup files for PSoC6 CM0
Added initial IAR linker and startup files for PSoC6 CM0
Added defines to disable some SPM protection settings for PSoC64
Moved Flash function variables into separate memory region
Added defines for new Public area definition
Updated PSoC6 CM0_PSA hex-files
Page size in all PSOC6 boards is 512 bytes. This is very problematic in
all storage applications. This change reduces the page size (in flash_api's
flash_program_page API) to 32 by reading the original page, modifying it
with programmed data and programming it back. The number 32 for page size
conforms to the number of times (16) this action can be done.
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Instead of user defined symbols in assembly files or C files,
use linker scripts to add heap and stack - this is inconsistent
with ARM std linker scripts
Due to a bug the LPTIM peripheral can cause interrupts to fire at the
wrong time on the NUCLEO_L073RZ. This patch switches the backend
of the low power ticker to the RTC until this bug is addressed.
Nuvoton M2351 was including generic core_armv8mbl.h from CMSIS - we
need it to be more specific to identify the specific core for
wait_ns. Change to core_cm23.h.
I implemented USB Device feature for Renesas mbed boards.
The code referenced the following code as a starting point and is implemented it by inheritting USBPhy same as other boards.
(mbed-os\features\unsupported\USBDevice\targets\TARGET_RENESAS)
When activating an endpoint assign new data rather than ORing
data to it. This ensures that values set from the previous use
do not effect the current configuration.
Update the patch "Create HAL_PCD_EP_Abort" to fix bugs.
This patch adds the low level functions USB_EPStopXfer, USB_EPSetNak,
USB_EPClearNak and the high level function HAL_PCD_EP_Abort so that
transfers can be stopped.
The functions USB_EPSetNak and USB_EPClearNak allow nak to be enabled
or disabled for an endpoint, preventing or allowing further transfers.
The function USB_EPStopXfer stops pending reads and writes started by
USB_EPStartXfer along with clearing and masking any interrupts enabled
by USB_EPStartXfer.
The function HAL_PCD_EP_Abort aborts any transfers on the given
endpoint. When this function completes the transfer interrupt
is guarenteed not to fire for this endpoint. Furthermore, the size
of data transferred during an aborted read can be found by calling
the function HAL_PCD_EP_GetRxCount.
Other notes on this Change:
1.
Prior to this patch the interrupt USB_OTG_DOEPINT_EPDISD was not
handled. When an OUT endpoint was disabled this interrupt occurred
causing the CPU to get stuck repeatedly handling this interrupt. This
is because this interrupt was unmasked but nothing cleared this
interrupt. This patch also adds code to handle and clear this
interrupt to prevent a lockup.
2.
Stopping a transfer on an OUT endpoint requires global nak OUT to
be in effect. Even with this being done, having entries in the rx fifo
prevented an OUT endpoint from being disabled. This behavior is not
mentioned in the Reference Manual.
Take the code from
mbed-os\features\unsupported\USBDevice\targets\TARGET_STM
as a starting point and use it to fill in the USBPhy template for STM32
devices.
Move the USBPhy header files into usb/device/USBPhy. Also move hal
and target USB files since mbed 2 does not compile when these files
are present without the USBPhy headers.
Directory restructure summary:
platform/USBPhy*
to usb/device/USBPhy/USBPhy*
hal/*
to usb/device/hal/*
targets/TARGET_Freescale/usb/*
to usb/device/targets/TARGET_Freescale/*
targets/TARGET_NXP/TARGET_LPC176X/usb/*
to usb/device/targets/TARGET_NXP/*
Make the following changes to improve stability:
-When disconnecting set address to disabled to prevent nacks
-Clear EP_SLOW one and only once for every interrupt where it is set_address
-Disable and clear control endpoint interrupts when disconnecting
Even thought the USB phy is disabled during disconnect, endpoints
still nack packets sent. This patch disables all endpoints so after
disconnect no USB traffic will be sent. This allows brief disconnects
of ~200us (or more) to be reliably detected by the host PC.
Reverting this feature till IAR 8.x is stable and supported in Mbed OS
for few releases
1. Revert "Add Dynamic heap support to IAR"
This reverts commit 8ee29bbfa2.
2. Revert "Splited RAM section not compatible with dynamic HEAP."
This reverts commit a645bb2a6b.
3. Revert "Add Dynamic heap support to IAR"
This reverts commit 891e1f261b.
Two new block properties available in linker configuration files:
"expanding size" and "minimum size" for IAR 8.11.2 and above
Sample:
define block HEAP with expanding size, minimum size = 16K, alignment = 8 {};
This block will expand to consume all remaining available space in
the range where it is placed. If several such blocks end up in the same
range, they will share the remaining space.
Cannot place a block with expanding size inside another block with
expanding size, inside a block with maximum size, or inside an overlay.
Few targets have libraries compatible to IAR 7.x, which fail with
IAR 8.x, IAR support for them is removed till updated library is
added.
CI failure seen if IAR is not added as supported target, trying with
release_version as empty string
List of targets affected:
1. UBLOX_EVK_ODIN_W2
2. MTB_UBLOX_ODIN_W2
3. MBED_CONNECT_ODIN
4. MTB_MXCHIP_EMW3166
5. MTB_ADV_WISE_1530
6. MTB_USI_WM_BN_BM_22
7. REALTEK_RTL8195AM
RAM define/section if splited, IAR exanpding size considers just one
section while heap creation which results in smaller chunk for heap.
This commit is to unify the RAM section.
Two new block properties available in linker configuration files:
"expanding size" and "minimum size" for IAR 8.11.2 and above
Sample:
define block HEAP with expanding size, minimum size = 16K, alignment = 8 {};
This block will expand to consume all remaining available space in
the range where it is placed. If several such blocks end up in the same
range, they will share the remaining space.
Cannot place a block with expanding size inside another block with
expanding size, inside a block with maximum size, or inside an overlay.
The low power ticker wrapper layer adds a large amount of interrupt
latency. This can cause dropped bytes at a baud of 115200 on some
devices. To prevent this by default use the microsecond ticker for
tickless on devices which make use of the low power ticker wrapper.
Fix port_write API to correctly shift the passed value.
This allows the reference application provided in PortOut docs
to work corectly with arbitrary LED_MASK.
https://os.mbed.com/docs/mbed-os/v5.11/apis/portout.html
The fix applies to both PSOC6 and PSOC6_FUTURE HAL implementations.
Fix for issue #9450 by adding turning off the modem power at startup, so that modem is sure to be in the initial state.
Fix for wrong filename and classname.
// WIP
Main thread stack size is reduced for TARGET_STM32F070RB and TARGET_STM32F072RB,
in recent update to mbed_rtx.h the conditional check for main thread size update
was removed.
Memory model for RTOS and No RTOS was initially single stack and heap,
only few targets implemented 2-region RAM model.
2-region RAM model is applied for all toolchains and targets.
GCC: __wrap__sbrk was implemented for 2-region ram model, with switch to 2-region
for all targets, we do not need target specific implementation of this API
Also _sbrk is WEAK function, hence can be over written in target folder for
special cases
The NRF52_DK and DELTA_DFBM_NQ620 have the SWO pin (p0_18) mapped to
LED2. This means that on startup LED2 turns on after the ITM is
initialized which is confusing. Since most users want LED2 usage
instead of SWO we remove the ITM for these targets.
The nRF52 readme is updated to instruct users how to get SWO support
if they need it.
Use ModusToolbox Device Configurator 1.1.0.284 to generate the
BSP low-level initialization code. Compatible version of Device
Configurator to be released with ModusToolbox 1.1.
Notable changes:
* rename cycfg_connectivity -> cycfg_routing
* switch LF_CLK clock source from ILO to WCO on
CY8CPROTO-062-4343W and CYW943012P6EVB-01
An entropy source is required in order to use the PSA Crypto API. The
only devices Mbed OS knows are guaranteed by default to have an entropy
source are those devices with a TRNG. Don't enable the PSA Crypto API by
default for devices that Mbed OS can't know have an entropy source. This
avoids run-time errors when an entropy source is not present on these
targets.
Applications can add their own entropy source by place entropy into
their systems, implementing their own NV Seed read and write callbacks,
and then enabling the MBEDTLS_ENTROPY_NV_SEED configuration option to
notify the PSA Crypto implementation that an entropy source is present
and how to use it.
See https://os.mbed.com/docs/mbed-os/v5.11/porting/entropy-sources.html
for the background on why entropy is fundamental to system security and
how to inject entropy into systems that lack an on-board source of
entropy.
Enabled tickless mode for Sequana PSA M0 core code to allow it to enter
deep sleep mode. This fixes issue #9094 where tests were failing due to
M0 core not entering deep sleep mode, blocking the whole chip.
Fixed incorrect resource management on M0 core, which crashed tickless
mode.
Linker files for LPC11U68 and LPC1549 updated as Mbed OS memory model
1. LPC1549
Has multiple memory banks, 4K bank used for stack exclusively and 16K for Heap
Its is mbed 2 only target hence 4K for stack.
2. LPC11U68
Added Heap and Stack sections in linker files. Resolved build issues.
Port of NUC472/M487 crypto AC mgmt work to M2351:
1. Choose mutex to synchronize access to crypto non-SHA AC
2. Choose atomic flag to synchronize access to crypto SHA AC
1. Removed random i/o glitches occurring during device reconfiguration
2. Fixed hazardous reads occurring at the end of transfer resulting
in incorrect values being received
3. Added spi_free() function
4. Replaced default M0 image with a one ignoring i/o reservation. This is
a workaround for missing proper destructors in Mbed drivers and BlockDevice
tests failing on repeated initialization
Fixes issue #9620.
Add support for listing all the pins of one or more form factors.
This is in preparation for automated testing of the default form
factor.
This patch includes the following:
-A function to get a list of restricted pins which should not be
used for testing due to some caveat.
-The target config "default-form-factor" which can specify which form
factor should be tested
-Form factor information for the arduino form factor
Add the functions qspi_master_sclk_pinmap, qspi_master_ssel_pinmap and
qspi_master_data0_pinmap-qspi_master_data3_pinmap to all targets with
qspi support.
Arto Kinnunen
Alexander Zilberkant
Oren Cohen
Mahesh Mahadevan
Michael Schwarcz
Leszek Rusinowicz
Sarah Marsh
Kyle Kearney
Neil Tuttle
Neil Tuttle
Shuopeng Deng
Vivek Pallantla
Sergii Vozniak
Oleg Kapshii
Netanel Gonen
David Saada
Martin Kojtal
Senthil Ramakrishnan
Kevin Bracey
Deepika
Cruz Monrreal
Seppo Takalo
d-kato
Russ Butler
Moran Peker
itayzafrir
j3hill
Moran Peker
Jarno Lamsa
Lei Zhang
jeromecoutant
Amir Cohen
Donatien Garnier
panyz0725@thundersoft.com
bcostm
TomoYamanaka
Russ Butler
Michel Jaouen
Maciej Bocianski
aqin
Oren Cohen
Guillermo Alonso
Ashok Rao
Volodymyr Medvid
Yoshihiro TSUBOI
Przemyslaw Stekiel
RFulchiero
Marcin Tomczyk
Teppo Järvelin
Jaeden Amero
Cai
Fahim Alavi
ccli8