Updated Serial Flash interface & Network buffer classes to avoid warnings and improve robustness. Fixed issue with mbed_overrides trying to use an old implementation of cy_serial_flash_init() function.
Implementation of pwmout_read() is not consistent with the requirements.
This function should return the current float-point output duty-cycle in range <0.0f, 1.0f>.
Currently it returns decimal percentage value.
ARM Compiler 6.13 testing revealed linker errors pointing out
conflicting use of `__user_setup_stackheap` and
`__user_initial_stackheap` in some targets. Remove the unwanted
`__user_initial_stackheap` from the targets - the setup is
centralised in the common platform code.
Looking into this, a number of other issues were highlighted
* Almost all targets had `__initial_sp` hardcoded in assembler,
rather than getting it from the scatter file. This was behind
issue #11313. Fix this generally.
* A few targets' `__initial_sp` values did not match the scatter
file layout, in some cases meaning they were overlapping heap
space. They now all use the area reserved in the scatter file.
If any problems are seen, then there is an error in the
scatter file.
* A number of targets were reserving unneeded space for heap and
stack in their startup assembler, on top of the space reserved in
the scatter file, so wasting a few K. A couple were using that
space for the stack, rather than the space in the scatter file.
To clarify expected behaviour:
* Each scatter file contains empty regions `ARM_LIB_HEAP` and
`ARM_LIB_STACK` to reserve space. `ARM_LIB_STACK` is sized
by the macro `MBED_BOOT_STACK_SIZE`, which is set by the tools.
`ARM_LIB_HEAP` is generally the space left over after static
RAM and stack.
* The address of the end of `ARM_LIB_STACK` is written into the
vector table and on reset the CPU sets MSP to that address.
* The common platform code in Mbed OS provides `__user_setup_stackheap`
for the ARM library. The ARM library calls this during startup, and
it calls `__mbed_user_setup_stackheap`.
* The default weak definition of `__mbed_user_setup_stackheap` does not
modify SP, so we remain on the boot stack, and the heap is set to
the region described by `ARM_LIB_HEAP`. If `ARM_LIB_HEAP` doesn't
exist, then the heap is the space from the end of the used data in
`RW_IRAM1` to the start of `ARM_LIB_STACK`.
* Targets can override `__mbed_user_setup_stackheap` if they want.
Currently only Renesas (ARMv7-A class) devices do.
* If microlib is in use, then it doesn't call `__user_setup_stackheap`.
Instead it just finds and uses `ARM_LIB_STACK` and `ARM_LIB_HEAP`
itself.
Notes:
- CRC and TRNG are disabled on this board since the MCU on this board does not have the required hardware.
- QSPI and QSPIF are temporarily removed due to issues related to supporting the new S25FS512S flash chip we have on this board. These will be enabled as soon as we can get the issues resolved.
https://github.com/ARMmbed/mbed-os/issues/11722
None of the USB drivers currently support entering deep sleep mode
while USB is active. To protect USB from malfunctioning lock deep
sleep in USBPhyHw::init.This is done for similar
This was done for all other implementations as part of
https://github.com/ARMmbed/mbed-os/commit/8ffbe5c6033
The port configuration api was not correctly setting the port-pins'
direction. Changed the port driver to call the gpio driver for
configuration (read and write still are optimized for port-level
operations) so that the behavior is consistent.
The cyhal_spi_send api was changed to read and discard a byte on every
send operation (at the protocol level all SPI transfers are bidirectional).
This means that to achieve a truly bidirectional transfer, the
cyhal_spi_transfer API must be called (as opposed to a write followed
by a read).
The QSPI spec allows alt to be any size that is a multiple of the
number of data lines. For example, Micron's N25Q128A uses only a
single alt cycle for all read modes (1, 2, or 4 bits depending on
how many data lines are in use).
- Fixed miscalculation in SPI frequency setup (divider value).
- Added possibility to set up SCK line as NC (usable when SPI peripheral
is used to handle non-SPI protocols.
- Fixed handlingh of 16-bit (and other >8 bit) transfers.
(cherry picked from commit 7d391f257b4ff6cdd7b43eeaa4894f8ce6d2cf8e)
Remove some (Cypress-proprietary) BSP interfaces and hardware initialization
from the BSPs which is better implemented by a library or application firmware.
Move some remaining functionality from common to the individual targets.
Don't malloc during wifi initialization, as that could cause double allocation in some cases.
The thread stack will be allocated by cy_rtos_thread_start if necessary.
yarb
Martin Kojtal
Ryan Morse
Przemyslaw Stekiel
Kevin Bracey
Hugues Kamba
Shuopeng Deng
Roman Okhrimenko
Anna Bridge
Kyle Kearney
Matthew Macovsky
Leszek Rusinowicz
int_szyk
Volodymyr Medvid