Limit NUCLEO_H723ZG toolchain to GCC_ARM only.
This is the only toolchain this target has been tested with yet.
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
- add board specific EMAC setup to connectivity/drivers/emac/TARGET_STM/TARGET_STM32H7
- stm32h7_eth_init.c was derived from the NUCLEO-H743ZI2 code whilst comparing to the output of STM32CubeIDE
- complete board specific code in targets/TARGET_STM/TARGET_STM32H7/TARGET_STM32H723xG
- PeripheralPins.c and PinNames.h were created by targets/TARGET_STM/tools/STM32_gen_PeripheralPins.py
- ST ZIO connector pins in PinNames.h have been adapted from NUCLEO-H743ZI2
- CONSOLE_TX and CONSOLE_RX have been interchanged in PinNames.h to match the actual board layout
- startup_stm32h723xx.S was derived from startup_stm32h743xx.S
- stm32h723xg.ld was completely rewritten to match the actual MCU including:
- split heap support
- SRAM2 and SRAM4 support
- crash dump support
- proper use of DTCM as stack
- system_clock.c has been changed to support the maximal main clock speed of 550 MHz
- fix handling of HS in FS mode for the target board in targets/TARGET_STM/USBPhy_STM32.cpp
- add board definition to targets/targets.json and correct linker setup for the chip
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
Pinout comparison between NuMaker-M467HJ and NuMaker-IoT-M467 boards:
1. UNO are unchanged
2. LEDs are unchanged
3. Buttons are unchanged, except button names
4. NuMaker-M467HJ has HBI but NuMaker-IoT-M467 does
5. NuMaker-M467HJ doesn't have ESP8266 but NuMaker-IoT-M467 does
6. SDHC are unchanged
Some M460 chips don't support AES/SHA/ECC/RSA H/W.
Make them removable from mbedtls H/W port through '"target.macros_remove": ["MBEDTLS_CONFIG_HW_SUPPORT"]'.
1. Crypto RSA H/W supports 1024/2048/3072/4096 key bits. Fall back to software implementation for other key bits.
2. For decrypt, if MBEDTLS_RSA_NO_CRT isn't defined, go CRT, or normal.
3. For decrypt, when blinding (f_rng != NULL), enable SCAP mode.
4. Recover from Crypto RSA H/W failure:
(1) Enable timed-out wait to escape from RSA H/W trap
(2) On RSA H/W timeout, stop this RSA H/W operation
(3) Fall back to S/W implementation on failure
NOTE: RSA 4096 key bits can fail with default mbedtls configuration MBEDTLS_MPI_MAX_SIZE.
Enlarge MBEDTLS_MPI_MAX_SIZE to 1024 or larger if this feature is required.
NOTE: Fixed in BSP RSA driver, for non-CRT+SCAP mode, temporary buffer for MADDR6 requires to be key length plus 128 bits.
NOTE: Fixed in BSP RSA driver, DMA buffer must be 4-word aligned, or RSA H/W will trap.
1. Prepare crypto common code
2. Support list
- SHA
- ECC
NOTE: AES/RSA are to support in other works
NOTE: Compared to M487, M467's SHA supports context save & restore (DMA Cascade mode) and so no software fallback is needed.
NOTE: M467's ECC, following M487, goes partial-module replacement and it can just improve primitives e.g. point addition/doubling by 2X,
and cannot improve high level point multiplication because MbedTLS doesn’t open it.
To improve performance best, full-module replacement is needed.
NOTE: Continuing above, add support for Montgomery curve
1. For GCC, support multi-block .data/.bss initialization
2. HyperRAM is mapped to two regions: 0x0A000000 and 0x80000000
According to default system address map, 0x0A000000 is located at 'Code' region and 0x80000000 at 'RAM' region.
With MPU enabled on Mbed OS, 'Code' region is write-never and 'RAM' region execute-never.
0x80000000 is chosen because 'RAM' regioin is naturally for HyperRAM.
3. Configurable multi-function pins for HBI
4. To locate code/data at external HyperRAM:
- Specify __attribute__((section(".text.nu.exthyperram"))) for RO/.text/readonly section type
Invoke mbed_mpu_manager_lock_ram_execution()/mbed_mpu_manager_unlock_ram_execution() to run HyperRAM code
- Specify __attribute__((section(".data.nu.exthyperram"))) for RW/.data/readwrite section type
- Specify __attribute__((section(".bss.nu.exthyperram"))) for ZI/.bss/zeroinit section type
5. Add readme
1. Based on alpha version BSP (85564a2716548e7b6d6a79a490c6d94a24cf9bcf)
2. Continuing above, tweak BSP:
(1) Add EPWM_ConfigOutputChannel2() to enable below 1Hz and below 1% duty cycle for PWM output (m460_epwm.h/c).
(2) Add dummy RTC_WaitAccessEnable() for consistency with previous ports (m460_rtc.h).
3. Target NuMaker-M467HJ V0.1 board temporarily
4. Support Arduino UNO form factor for NUMAKER_IOT_M467 target
5. Enable export to Keil/IAR project
- tools/arm_pack_manager/index.json
- tools/export/iar/iar_definitions.json
RFC3315 specifies the following: "The relay agent MAY send the Interface-id
option to identify the interface on which the client message was received.
If a relay agent receives a Relay-reply message with an Interface-id
option, the relay agent relays the message to the client through the
interface identified by the option."
The current implementation of the DHCP relay reply handling, the interface
ID field from the server response is ignored. Managing the interface ID
is very important especially as DHCP requests/replies use link-local
addresses. The consequence of this is that the interface must always be
specified because the routing layer cannot guess the correct interface.
Moreover, Mbed provides a mechanism to enable/disable the interface ID
option on a DHCP relay instance, so it is important to fully support it.
The reason why this issue has not been discoverd until now is that the DHCP
relay is mainly used on systems that use only one interface (such as Wi-SUN
routers). By default, when no interface ID is specified for the socket, the
latter will choose 6loWPAN interface by default. This means that if two
interfaces are used on the same device, the 6loWPAN interface is always
selected.
The commit adds code to retrieve the interface-id value contained within
the DHCP relay reply message and write it to a control message header
that is added to the socket message. This tells the socket which
interface to choose. If the interface-id option is not enabled on the
relay, this procedure is simply ignored.
Deepak V. Shreshti
Martin Kojtal
cyliangtw
Daniel Starke
Ahmet Alincak
Sadik.Ozer
Chun-Chieh Li
chdelfs
YannCharbon