Fixed interrupt vector settings on M0 core. Wrong vector settings prevented
LP_TICKER from working, resulting in deep sleep tests failing on M0
or PSA variant.
Internal channels use is enabling ADC "internal path" which needs
to be disabled after measurement.
Same applied here for WB family as was done for others in #10143.
Typically the RTC clock is configured by RTC driver itself.
RNG on the other hand is shared with M0+ core and it is expected that
M4 turns it on at boot time.
When doing so, do not disbale GPIO clocks as they may be used by other
drivers !
As a result, debug will be disabled by default, but can be enabled by
either modifying code or selecting MBED debug profile.
Review HSE clock initialization to match with latest CUBE firmware.
Also there is no need to set the full clock tree again after deep sleep exit.
With this change we get a stable deep sleep mode (when allowed by CORDIO stack).
Until the CMSIS pack device name is officially deployed.
then we'll the name as can be found in Keil CMSIS pack
<!-- ************************* Device 'STM32WB55RG' ***************************** -->
<device Dname="STM32WB55RGVx">
<memory id="IROM1" start="0x08000000" size="0x001000000" startup="1" default="1" />
<memory id="IRAM1" start="0x20000000" size="0x000040000" init="0" default="1" />
<algorithm name="CMSIS/Flash/STM32WB_M4.FLM" start="0x08000000" size="0x001000000" default="1" />
<feature type="QFP" n="68"/>
</device>
There is no need to add FIRST attribute to MAPPING_TABLE as the default
ordering is alphabetical order.
With this change, we don't have any warning with MBED2 and the sections
are properly ordered anyway in BLE cases.
In case of mbed2, BLE feature is not built.
As there is a MAPPING_TABLE in BLE feature which is not compiled in case
of mbed2, the linker reported the below error
[ERROR] "C:/Data/Workspace/mbed/BUILD/test/NUCLEO_WB55RG/ARM/MBED_2/
.link_script.sct", line 65 (column 6): Error: L6236E:
No section matches selector - no section to be FIRST/LAST.
Solution is to check whether BLE is enabled.
These files are not BLE specific, but also needed for some clock setting
for instance.
In order to compile an MBED2 application, we need to move the files.
- move hw_conf.h file to targets/TARGET_STM/TARGET_STM32WB directory as
this is used also out of BLE feature.
- create a dedicated hal_deepsleep function as the behavior in WB is a lot
different from other existing STM32 targets
- update clock tree configuration to directly clock the entire tree @ 32MHz
out of HSE. This is needed as we want to let the M0 core running without
any change on M0-side of clocks when M4 enters /exits deep sleep.
Needed for PSoC to deep-sleep for more than 2 seconds
Max sleep with 16 bit lp_ticker (before this change) : 2sec
Max sleep with 32 bit lp_ticker (after this change) : 36hours
The cache must be refreshed when we erase or program flash memory.
It fix 2 issues :
Fix#9934Fix#6380
This solution was initially proposed in #6380.
Signed-off-by: Vincent Veron <vincent.veron@st.com>
The OS timer of RZ/A1 uses P0 clock, so until now it has been set the value of P0 clock in SystemCoreClock.
Changed the system clock value to set to SystemCoreClock.
Changed to refer to P0 clock macro instead of SystemCoreClock in OS timer processing.
Nuvoton targets below don't provide SPI-bus SD on-board, identified by 'SD' in
target component list. Instead, these targets provide SD-bus SD on-board, identified
by unofficial 'NUSD', driver of which is provided outside mbed-os tree. So 'SD' must
be removed to reflect the truth.
- NUMAKER_PFM_NUC472
- NUMAKER_PFM_M487
- NUMAKER_IOT_M487
- NUMAKER_PFM_M2351
The flash driver for the LPC55S69 is different from
prior LPC family. Move the Flash HAL driver to SoC
specific folder
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This data, placed at physically not existing addresses (0x9xxxxxxx) was used
only by PSoC Programmer and KitProg2 and is no longer needed, but was causing
issues with standard hex file processing tools like srecord (srec_cat).
If the board-specific initialization code configures the serial port to
use an 8-bit divider, the serial_init_clock function would configure the
16-bit divider with the same index instead of the intended 8-bit
divider.
Added WiFi_Bt CM4 PSA target in mbedos json
Added SPE-NSPE mailbox initialization for CM4 SystemInit
Made similar to FUTURE_SEQUANA configurations
Copied FUTURE_SEQUANA CM0 SPM part for WiFi_Bt smoke test
Added CY8CKIT_062_WIFI_BT_M0 and CY8CKIT_062_WIFI_BT_M0_PSA targets
Sorted files for new CY8CKIT_062_WIFI_BT_M0 and CY8CKIT_062_WIFI_BT_M0_PSA targets
Copied files for CY8CKIT_062_WIFI_BT_M0_PSA from FUTURE_SEQUANA
Copied and updated cm0p start files
Corrected according to FUTURE_SEQUANA
Changes to M0 startup files to have SPM started
Fixed implicit declaration warning
Commented interrupts enabling according to FUTURE_SEQUANA flow
Updated prebuild spm_smore CM0 hex for CM4 target
Turned on greentea environment
Used special memory region for common CM0/CM4 data
Updated prebuild CM0 SPM hex
Placed shared memory region for flash operations into SPM shared memory region
Updated cyprotection code and configuration
Start address of protected regions is set by a defined number from target.json
Added masters pcMask configuration
Added support for PSA target to WIFI_BT board
Enabled resources protection for SPM
Aligned RAM usage according to Cypress FlashBoot and CyBootloader
alligned protection config
Added CYW943012P6EVB_01_M0 target
Enlarged heap size, remobed nv_seed
Added heap reservation in linker script from mbed-os
Removed heap size definition
turned on nv_seed config
Removed nv_seed macros
Enabled protection for PSoC6 CM0
Added PSoC6 CM0 PSA readme
Enabled mbed_hal-spm test
Enabled nv_seed and removed unneeded ipc config define
Added SPDX string to feature_ble cypress target files
Removed unneeded supported_toolchains lines for Cypress targets
Disabled protection settings
Corrected flash initialization for PSoC6 CM0 PSA
Changed PSoC6 IPC6 protection for flash
Enabled special flash initialization and enabled protection settings
Updated and added new prebuild PSoC6 CM0 PSA hex files
Disabled HW TRNG and CRC for PSoC6 CM4 PSA target
Added missing const to allow types to match
Updated PSoC6 WIFI_BT_PSA prebuilt directory
Moved PSoC6 shared section usage area definition to begin of ld
Added initial ARM_STD linker and startup files for PSoC6 CM0
Added initial IAR linker and startup files for PSoC6 CM0
Added defines to disable some SPM protection settings for PSoC64
Moved Flash function variables into separate memory region
Added defines for new Public area definition
Updated PSoC6 CM0_PSA hex-files
Vincent Veron
Qinghao Shi
adbridge
Ashok Rao
Leszek Rusinowicz
Laurent Meunier
bcostm
jeromecoutant
Ganesh Ramachandran
junichi.katsu@uhuru.jp
Brian Daniels
Vivek Pallantla
Lei Zhang
Mahesh Mahadevan
ecoromka
d-kato
ccli8
Oren Cohen
Michael Schwarcz
Ryan Morse
Malavika Sajikumar
Juho Eskeli
Jan Jongboom
Oleg Kapshii
Wajahat Abbas
Michael Coulter
mudassar-ublox
Alexander Zilberkant
David Saada
Yossi Levy
Oren Cohen
Evgeni
Cruz Monrreal II
Arto Kinnunen
Alexander Zilberkant
Sarah Marsh
Kyle Kearney
Neil Tuttle
Neil Tuttle
Shuopeng Deng
Sergii Vozniak