- Add the no confidentiality & no replay protection flags
- Add actual size parameter in PS/ITS get APIs
- Change a few size parameters from uint32_t to size_t
During the SiP workshop, we discovered that 3% is too narrow due to a combination of:
Voltage rail differences between target and FPGA
Extension of lesser-resolution ADC's to 16-bit results
The test case which checks full range cannot be executed at the moment due to a hardware bug in FPGA-Test-Shield.
This test case will be restored when the final version of FPGA-Test-Shield is ready.
Watchdog::stop() is called in this test. If the target does not support
stopping the watchdog this case needs to be skipped.
Also improve handling ignored test cases.
Update the watchdog timing requirements:
1. The watchdog should trigger at, or after the timeout value.
2. The watchdog should trigger before twice the timeout value.
Use a SERIAL_FLUSH_TIME_MS value consistent with other tests.
Update the watchdog timing requirements:
1. The watchdog should trigger at, or after the timeout value.
2. The watchdog should trigger before twice the timeout value.
Update the watchdog timing requirements:
1. The watchdog should trigger at, or after the timeout value.
2. The watchdog should trigger before twice the timeout value.
Remove explicit calls to sleep.
Update the watchdog timing requirements:
1. The watchdog should trigger at, or after the timeout value.
2. The watchdog should trigger before twice the timeout value.
Update the watchdog timing requirements:
1. The watchdog should trigger at, or after the timeout value.
2. The watchdog should trigger before twice the timeout value.
With the DEEP_SLEEP_TEST_CHECK_WAIT_DELTA_US increased,
we now have TEST_ASSERT_UINT64_WITHIN(delta=1000, expected=1000, actual=1000)
so this assertion needed to be updated.
What we need is the deep sleep to be enabled after the programed interrupt
has fired and before a 2ms timeout expiration, which means >= 1000 and < 2000.
Running PowerShell script on some windows machines is blocked.
To avoid this problem script was replace by the code run directly in PowerShell console.
Changes:
- restore the original form of setup/teardown handlers,
- test_lock_unlock_test_check(): do not use common ticker layer (Timer, Timeout). Use only ticker HAL layer.
- Increase DEEP_SLEEP_TEST_CHECK_WAIT_DELTA_US delta.
Added a mechanism which will prevent an initialised watchdog from
resetting the device during final greentea communication.
This allows testing watchdog timeouts as short as 50 ms.
As the timer code became more generic, coping with initialization on
demand, and variable width and speed us_ticker_api implementations,
wait_us has gradually gotten slower and slower.
Some platforms have reportedly seen overhead of wait_us() increase from
10µs to 30µs. These changes should fully reverse that drop, and even
make it better than ever.
Add fast paths for platforms that provide compile-time information about
us_ticker. Speed and code size is improved further if:
* Timer has >= 2^32 microsecond range, or better still is 32-bit 1MHz.
* Platform implements us_ticker_read() as a macro
* Timer is initialised at boot, rather than first use
The latter initialisation option is the default for STM, as this has
always been the case.
Update the watchdog timing requirements:
1. The watchdog should trigger at, or after the timeout value.
2. The watchdog should trigger before twice the timeout value.
In particular and as kindly suggested by Przemec S. :
1. Add setup/teardown handler’s for all cases. This disables sys-tick,
so there should be no unexpected lp ticker interrupt scheduling.
2. Modify setup/teardown handler’s: remove suspension of lp/us tickers,
so they can count as this is required by test_lock_unlock_test_check test
case.
3. Use TEST_ASSERT_TRUE(sleep_manager_can_deep_sleep_test_check()) after
setting interrupt to cope with STM specific handling (CMPOK interrupt with
deep-sleep locked). This performs wait only if needed and will not affect
other targets which do not need extra wait.
4. Move sleep_manager_lock_deep_sleep() after TEST_ASSERT_TRUE(sleep_manager_can_deep_sleep_test_check())
5. Use TEST_ASSERT_TRUE(sleep_manager_can_deep_sleep_test_check()) in
test_lock_unlock_test_check to let lower layers manage deep sleep.
Time drifting test cases use serial communication with the host and are unstable on CI.
Skip time-drifting test cases if SKIP_TIME_DRIFT_TESTS macro is defined.
The idea for the future is to use FPGA test shield for timing tests instead of host scripts.
Also remove `__ARM_FM` macro which in most cases was used to disable time drifting tests. In other cases replace `__ARM_FM` with `TARGET_ARM_FM` which is more suitable.
Fix was to add some time between iterations connect-disconnect.
In cellular disconnect, cellular network may send disconnect events
and if those events come when connect is already ongoing test will fail.
So wait a bit after disconnect so that disconnect events should be over.
The Watchdog driver has been updated making these tests incompatible
with the new API. The Watchdog driver functionality is tested with the
unit tests located in UNITTESTS/drivers/Watchdog/ .
Do not call sleep from the test thread, but let scheduler do it.
And also include the deep sleep latency in the computation of the allowed
delta for deep sleep test case.
On some targets like STM family boards with LPTIM enabled an interrupt is triggered on counter rollover.
We need special handling for cases when next_match_timestamp < start_timestamp (interrupt is to be fired after rollover).
In such case after first wake-up we need to reset interrupt and go back to sleep waiting for the valid one.
On some targets like STM family boards with LPTIM enabled there is a required delay (~100 us) before we are able to reprogram LPTIM_COMPARE register back to back.
This is handled by the low level lp ticker wrapper which uses LPTIM_CMPOK interrupt. CMPOK fires when LPTIM_COMPARE register can be safely reprogrammed again.
This means that on these platforms we have additional interrupt (CMPOK) fired always ~100 us after programming lp ticker.
Since this interrupt wake-ups the board from the sleep we need to go to sleep after CMPOK is handled.
Background:
There is an errata in LPTIM specification that explains that CMP Flag
condition is not an exact match (COUNTER = MATCH) but rather a
comparison (COUNTER >= MATCH).
As a consequence the interrupt is firing early than expected when
programing a timestamp after the 0xFFFF wrap-around.
In order to
work-around this issue, we implement the below work-around.
In case timestamp is after the work-around, let's decide to program the
CMP value to 0xFFFF, which is the wrap-around value. There would anyway be
a wake-up at the time of wrap-around to let the OS update the system time.
When the wrap-around interrupt happen, OS will check the current time and
program again the timestamp to the proper value.
Deprecate wait() in favour of acquire(), try_acquire(),
try_acquire_for() and try_acquire_until().
Brings Semaphore more into line with CMSIS-RTOS 2 (which uses "acquire"),
itself (as it has "release"), and other classes having "try", "try for"
and "try until".
Also steps away from vague "wait" term - the primary operation here is
to acquire the semaphore, and this will of course sleep.
* capitalize driver class name,
* reword test docs for the driver & HAL,
* capitalize Mbed name,
* reword the comments explaining the SERIAL_FLUSH_TIME_MS macro.
Change the config parameter used as a delay before sending the sync
packet after the device reset in watchdog and reset_reason tests. Use
'forced_reset_timeout' instead of 'program_cycle_s'.
The latest rebase of the watchdog feature branch introduced errors in compiling
watchdog tests due to missing headers.
- Watchdog HAL API test
Include missing header files to main.cpp (mbed_wait_api.h, stdlib.h).
- Watchdog HAL API timing test
Include missing header files to main.cpp (us_ticker_api.h).
- Watchdog Driver API test
Include missing header files to main.cpp (mbed_wait_api.h, stdlib.h).
Inject mbed namespace into main.cpp to fix Watchdog name resolution.
On NUMAKER_PFM_NANO130 target, WDT's clock source is fixed to LIRC, which is much
less accurate than other targets. Enlarge delta define to pass this test.
due to partial implementation. Having FUTURE_SEQUANA_M0 and
FUTURE_SEQUANA PSA targets is misleading.
Signed-off-by: Devaraj Ranganna <devaraj.ranganna@arm.com>
Reason for needing greater timeout could be this test's performance.
UDPSOCKET_ECHOTEST_BURST_NONBLOCK is implementing the receiving
differently and is passing with 1 second timeout.
Get rid of a volatile, and use atomics to synchronise with the interrupt
routine instead.
Useful as a non-RTOS basic compilation check for the atomics - the
fuller atomic test relies on the RTOS.
These are platform tests, but rely on the RTOS to run multiple threads
to exercise it.
(The atomics are still useful in non-RTOS, to protect against interrupt
handlers, but testing versus other threads is easier. The implementation
is the same either way, so doesn't seem worth testing non-RTOS
specifically).
Kevin Bracey
David Saada
Evelyne Donnaes
Filip Jagodzinski
Arto Kinnunen
jeromecoutant
Steven Cooreman
Russ Butler
Chun-Chieh Li
Martin Kojtal
Devaraj Ranganna
Przemyslaw Stekiel
Przemyslaw Stekiel
Neil Tuttle
Maciej Bocianski
Laurent Meunier
Anna Bridge
Filip Jagodzinski
Tymoteusz Bloch
d-kato
Teppo Järvelin
Lingkai Dong
Mel W
Amanda Butler
Donatien Garnier
Steve Cartmell
Michael Schwarcz
Olli-Pekka Puolitaival
Mirela Chirica
Guillermo Alonso
Ryan Morse
Alexander Zilberkant
Michal Paszta
Oren Cohen