Remove the direct use of the microsecond and low power ticker from
the tests. This enforces that sleep mode is properly locked when
using timers. Furthermore, this prepares the codebase for new ticker
changes which allow differing clock frequencies and timer bit widths.
The lp_ticker test overrides the default ticker handler for the
low power ticker. This stops all other low power TimerEvents in the
system, including the ones for tickless, from getting called. Because
of this devices with tickless enabled malfunction during this test.
This patch fixes this problem by passing all lp ticker events it did
not trigger on to the TimerEvent irq handler.
Increase the Timeout period from 1ms to 10ms so interrupt latency has
1/10th the effect on the measurement. This prevents failures due to
interrupt latency causing a drift.
In case the target supports a page size of 1 byte, i.e. is able to
program flash 1 byte at a time, which is the case of STM32 F4 targets,
there is no reason for flash_device.program to return an error when
trying to write on an "unaligned" address.
This test exercises ticker API
- init should be executed just once
- read timestamp
Set interrupt should be tested via upper layer, as it does not provide
API to change handler that is invoked in the ISR ticker handler.
The test assumed that data written to flash would be memory mapped
and directly accessible. On some platform this is not the case
and data has to read back through an explicit read command.
The test has been changed to use the flash read command instead
of direct memory access.
2 test cases added, one for event in the past, one for event in future but very close
to the current time, thus once is set, it is already in the past, and we fire
interrupt immediately.
1) mbed-os-tests-mbedmicro-rtos-mbed-basic tests use to fail when run in loop
after 20-25, This was because the stack used by test application was in range of
744-840 bytes. So bumped the stack size to 1024 bytes.
2) Corrected the assert and taken out the assert which was not required.
In the new approach the host controls the device activity when the test
should start, finish and pass/fail status is send to device. Also deprecate
the test cases which can't accurately test.
Initialize all values of timeinfo in make_time_info. This prevents
the field 'tm_isdst' from getting inadvertently set to 1 causing
time to be off by 1 hour.
The use of mktime was causing a fault when called in interrupt handler because on GCC it lock the mutex protecting the environment, To overcome this issue, this patch add dedicated routine to convert a time_t into a tm and vice versa.
In the process mktime has been optimized and is now an order of magnitude faster than the routines present in the C library.
This test was removed because of its memory footprint.
Most of the memory consummed by the test itself was related to the instantion of test cases in RAM.
With the introduction of case_t which allows tests cases to live in FLASH, the memory footprint has been drastically reduced (860 bytes of RAM saved) and the ticker test can be reintroduced in the code base.
This is temporary, as this test does not fit to some 16kB RAM devices. This requires few more steps: some small devices are using big async HAL structures, RTX changes increased the RAM footprint, plus this test seems to be too big. With all these, it won't fit in RAM regions for some devices.
Reduce RAM consumption so all tests can still be built when using
CMSIS/RTX5. Also reduce clutter by removing the per target stack size
defines in the tests.
A units mistake led to passing 20000 seconds instead of 20000 milliseconds
to greentea. The would cause the test to spin for 6 hours if it got stuck
anywhere.
Fixes#4196. As someone might not be aware that settting default_lib to small has
some implications regarding thread safety, therefore we print an error.
While limitations in type inference prevent the event helper from
infering the type of generic function objects, there is nothing
technical preventing inference from the Callback class, where the
function type is encoded in the template parameters.
With adoption of the Callback class as the standard function
representation, it makes sense to support events created from
callback objects.
Previously, the RTOS threads test was conditionally change the thread
stack size for all test cases based on the target. Now, it uses the
default stack size for all targets when threads are created serially,
and uses a 512 byte stack for the threads that are created in parallel.
The tests try to:
* scan for available networks and check whether specified networks
are present in the results.
* connect to and disconnect from the specified network.
* repeats the scan tests while connected to a network.
* connect to a network and perform simple HTTP query.
Sarah Marsh
Deepika
Russ Butler
Maciej Bocianski
Shrikant Tudavekar
Anna Bridge
Russ Butler
Martin Kojtal
Jimmy Brisson
Filip Jagodzinski
Laurent MEUNIER
Bartek Szatkowski
YarivCol
Christopher Haster
Marcus Chang
Shrikant Tudavekar
Chris
adustm
Sam Grove
Vincent Coubard
kl-cruz
ccli8
0xc0170
Brian Daniels