7.0 KiB
| layout | title |
|---|---|
| documentation | PAB04 - ZWave |
{% include base.html %}
PAB04 Smart Energy Flow Meter
This describes the Z-Wave device PAB04, manufactured by Philio Technology Corp with the thing type UID of philio_pab04_00_000.
The device is in the category of Valve, defining Valves used to control water or gas. e.g. a flow stop valve..
The PAB04 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
This valves controller PAB04 is a security enabled wireless switch, based on Z-Wave Plus technology.
Connect PAB04 with an external water meter which can output pulse signals. PAB04 is able to detect instance water flow and the accumulated water.
Inclusion Information
Pressing On/Off button three times within 2 seconds will enter inclusion mode.
Exclusion Information
Pressing On/Off button three times within 2 seconds will enter exclusion mode.
General Usage Information
Channels
The following table summarises the channels available for the PAB04 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Sensor (WATER_FLOW) | water_flow | water_flow | ||
| Water meter (gal) | meter_water_gallons | meter_water_gallons | Water | Number |
| Water meter (m3) | meter_water_cubic_meters | meter_water_cubic_meters | Water | Number |
Switch
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Sensor (WATER_FLOW)
Channel type information on this channel is not found.
Water meter (gal)
Indicates the instantaneous water consumption.
The meter_water_gallons channel is of type meter_water_gallons and supports the Number item and is in the Water category. This is a read only channel so will only be updated following state changes from the device.
Water meter (m3)
Indicates the instantaneous water consumption.
The meter_water_cubic_meters channel is of type meter_water_cubic_meters and supports the Number item and is in the Water category. This is a read only channel so will only be updated following state changes from the device.
Device Configuration
The following table provides a summary of the 6 configuration parameters available in the PAB04. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Unit of Water Flow | Unit of Water Flow |
| 2 | Accumulated Water Report | Accumulated Water Report |
| 3 | Instant Water Flow Percent Reported | Instant Water Flow Percent Reported |
| 4 | Pulses per Liter | Pulses per Liter |
| 5 | Relay Control Mode | Relay Control Mode |
| 6 | Periodic Auto Report Timer | Periodic Auto Report Timer |
Parameter 1: Unit of Water Flow
Unit of Water Flow
The following option values may be configured, in addition to values in the range 1 to 2 -:
| Value | Description |
|---|---|
| 1 | US Gallon |
| 2 | KL |
The manufacturer defined default value is 2 (KL).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Parameter 2: Accumulated Water Report
Accumulated Water Report
The following option values may be configured, in addition to values in the range 0 to 1 -:
| Value | Description |
|---|---|
| 0 | Disable Report |
| 1 | Enable Report |
The manufacturer defined default value is 1 (Enable Report).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Parameter 3: Instant Water Flow Percent Reported
Instant Water Flow Percent Reported
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
The manufacturer defined default value is 10.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Parameter 4: Pulses per Liter
Pulses per Liter This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 1 to 32676 may be set.
The manufacturer defined default value is 450.
This parameter has the configuration ID config_4_2 and is of type INTEGER.
Parameter 5: Relay Control Mode
Relay Control Mode
The following option values may be configured, in addition to values in the range 0 to 1 -:
| Value | Description |
|---|---|
| 0 | Normally Closed |
| 1 | Normally Open |
The manufacturer defined default value is 0 (Normally Closed).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Parameter 6: Periodic Auto Report Timer
Periodic Auto Report Timer
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
The manufacturer defined default value is 60.
This parameter has the configuration ID config_6_2 and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The PAB04 supports 1 association group.
Group 1: Lifeline
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 1 node.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V9 | |
| COMMAND_CLASS_METER_V2 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SECURITY_V1 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.