19 KiB
| layout | title |
|---|---|
| documentation | HS-WD200+ - ZWave |
{% include base.html %}
HS-WD200+ Scene Capable Wall Dimmer Switch
This describes the Z-Wave device HS-WD200+, manufactured by HomeSeer Technologies with the thing type UID of homeseer_hswd200511_05_011.
This version of the device is limited to firmware versions above 5.11
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The HS-WD200+ supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
HS-WD200+ is a Z-Wave wall dimmer that’s designed for wireless on-off-dim control of connected dimmable lighting loads.
Inclusion Information
Put your Z-Wave controller into inclusion mode, tap the paddle of your new HomeSeer dimmer to begin the inclusion process. This will take a few moments to complete.
Exclusion Information
Put your Z-Wave controller into exclusion mode, tap the paddle of your new HomeSeer dimmer to begin the inclusion process. This will take a few moments to complete.
Channels
The following table summarises the channels available for the HS-WD200+ -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | scene_number | Number | |
| Sets switch mode of operation | config_decimal | config_decimal | Number | |
| Normal mode LED colour | config_decimal | config_decimal | Number | |
| Status mode LED 1 Colour | config_decimal | config_decimal | Number | |
| Sets LED operation (in normal mode) | config_decimal | config_decimal | Number | |
| Sets paddle’s load orientation | config_decimal | config_decimal | Number | |
| Status mode LED 2 Colour | config_decimal | config_decimal | Number | |
| Status mode LED 3 Colour | config_decimal | config_decimal | Number | |
| Status mode LED 4 Colour | config_decimal | config_decimal | Number | |
| Status mode LED 5 Colour | config_decimal | config_decimal | Number | |
| Status mode LED 6 Colour | config_decimal | config_decimal | Number | |
| Status mode LED 7 Colour | config_decimal | config_decimal | Number | |
| Status mode LEDs Blink frequency | config_decimal | config_decimal | Number |
Dimmer
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Scene Number
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
This channel provides the scene, and the event as a decimal value in the form <scene>.<event>. The scene number is set by the device, and the event is as follows -:
| Event ID | Event Description |
|---|---|
| 0 | Single key press |
| 1 | Key released |
| 2 | Key held down |
| 3 | Double keypress |
| 4 | Tripple keypress |
| 5 | 4 x keypress |
| 6 | 5 x keypress |
Sets switch mode of operation
0=Normal mode (load status) 1=Status mode (custom status)
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Normal mode LED colour
Sets the Normal mode LED colour
Possible values: 0-6
0=White, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 1 Colour
LED 1 is the Bottom LED
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Sets LED operation (in normal mode)
0= LED ON if load is OFF
1= LED OFF if load is OFF
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Sets paddle’s load orientation
0 = Top of Paddle turns load ON
1 = Bottom of Paddle turns load ON
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 2 Colour
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 3 Colour
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 4 Colour
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 5 Colour
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 6 Colour
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LED 7 Colour
LED 7 is the top LED
Possible values: 0-7
0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Status mode LEDs Blink frequency
Sets the dimmer Blink frequency for All LEDs in Status mode
Possible values: 0, 1-255
0=No blink, 1=100ms ON then 100ms OFF
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Device Configuration
The following table provides a summary of the 21 configuration parameters available in the HS-WD200+. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | Bottom LED Operation | Sets the operation of the bottom LED |
| 4 | Orientation | Set paddle load orientation |
| 11 | Remote Ramp Rate | Set dimmer ramp rate for remote control |
| 12 | Local Ramp Rate | Set dimmer ramp rate for local control |
| 13 | Status Mode | Set dimmer display mode |
| 14 | Load Status LED Color | Set the LED color when displaying load status |
| 21 | Status LED 1 Color | Status LED 1 Color (bottom) |
| 22 | Status LED 2 Color | Status LED 2 Color |
| 23 | Status LED 3 Color | Status LED 3 Color |
| 24 | Status LED 4 Color | Status LED 4 Color |
| 25 | Status LED 5 Color | Status LED 5 Color |
| 26 | Status LED 6 Color | Status LED 6 Color |
| 27 | Status LED 7 Color | Status LED 7 Color (top) |
| 30 | Blink Frequency | Set blink frequency when displaying custom status |
| 31 | LED 1 Blink Status | LED 1 Blink Status (bottom) |
| 31 | LED 2 Blink Status | LED 2 Blink Status |
| 31 | LED 3 Blink Status | LED 3 Blink Status |
| 31 | LED 4 Blink Status | LED 4 Blink Status |
| 31 | LED 5 Blink Status | LED 5 Blink Status |
| 31 | LED 6 Blink Status | LED 6 Blink Status |
| 31 | LED 7 Blink Status | LED 7 Blink Status (top) |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Parameter 3: Bottom LED Operation
Sets the operation of the bottom LED
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Bottom LED ON if load is OFF |
| 1 | Bottom LED OFF if load is OFF |
The manufacturer defined default value is 1 (Bottom LED OFF if load is OFF).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Parameter 4: Orientation
Set paddle load orientation
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Top of Paddle turns load ON |
| 1 | Bottom of Paddle turns load ON |
The manufacturer defined default value is 0 (Top of Paddle turns load ON).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Parameter 11: Remote Ramp Rate
Set dimmer ramp rate for remote control
Values in the range 0 to 90 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Parameter 12: Local Ramp Rate
Set dimmer ramp rate for local control
Values in the range 0 to 90 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Parameter 13: Status Mode
Set dimmer display mode
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Load Status |
| 1 | Custom Status |
The manufacturer defined default value is 0 (Load Status).
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Parameter 14: Load Status LED Color
Set the LED color when displaying load status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | White |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
The manufacturer defined default value is 0 (White).
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Parameter 21: Status LED 1 Color
Status LED 1 Color (bottom)
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_21_1 and is of type INTEGER.
Parameter 22: Status LED 2 Color
Status LED 2 Color
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_22_1 and is of type INTEGER.
Parameter 23: Status LED 3 Color
Status LED 3 Color
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_23_1 and is of type INTEGER.
Parameter 24: Status LED 4 Color
Status LED 4 Color
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_24_1 and is of type INTEGER.
Parameter 25: Status LED 5 Color
Status LED 5 Color
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_25_1 and is of type INTEGER.
Parameter 26: Status LED 6 Color
Status LED 6 Color
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_26_1 and is of type INTEGER.
Parameter 27: Status LED 7 Color
Status LED 7 Color (top)
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_27_1 and is of type INTEGER.
Parameter 30: Blink Frequency
Set blink frequency when displaying custom status
The following option values may be configured, in addition to values in the range 0 to 255 -:
| Value | Description |
|---|---|
| 0 | No Blink |
| 1 | Blink 100ms ON, 100ms OFF |
| 2 | Blink 200ms ON, 200ms OFF |
| 3 | Blink 300ms ON, 300ms OFF |
| 4 | Blink 400ms ON, 400ms OFF |
| 5 | Blink 500ms ON, 500ms OFF |
The manufacturer defined default value is 0 (No Blink).
This parameter has the configuration ID config_30_1 and is of type INTEGER.
Parameter 31: LED 1 Blink Status
LED 1 Blink Status (bottom)
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000001 and is of type INTEGER.
Parameter 31: LED 2 Blink Status
LED 2 Blink Status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000002 and is of type INTEGER.
Parameter 31: LED 3 Blink Status
LED 3 Blink Status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000004 and is of type INTEGER.
Parameter 31: LED 4 Blink Status
LED 4 Blink Status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000008 and is of type INTEGER.
Parameter 31: LED 5 Blink Status
LED 5 Blink Status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000010 and is of type INTEGER.
Parameter 31: LED 6 Blink Status
LED 6 Blink Status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000020 and is of type INTEGER.
Parameter 31: LED 7 Blink Status
LED 7 Blink Status (top)
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Solid |
| 1 | Blink |
The manufacturer defined default value is 0 (Solid).
This parameter has the configuration ID config_31_1_00000040 and is of type INTEGER.
Switch All Mode
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The HS-WD200+ supports 2 association groups.
Group 1: Lifeline
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Lifeline association only supports the "manual reset" event.
Association group 1 supports 5 nodes.
Group 2: Companion Sync
Any device added to group 2 will be controlled. This allows other WX200 devices to used as companion switches. LEDS will be kept in sync.
Association group 2 supports 5 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_CENTRAL_SCENE_V3 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.