---
layout: documentation
title: HS-WD200+ - ZWave
---

{% include base.html %}

# HS-WD200+ Scene Capable Wall Dimmer Switch
This describes the Z-Wave device *HS-WD200+*, manufactured by *[HomeSeer Technologies](http://www.homeseer.com/)* with the thing type UID of ```homeseer_hswd200511_05_011```.
This version of the device is limited to firmware versions above 5.11

The device is in the category of *Wall Switch*, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

![HS-WD200+ product image](https://opensmarthouse.org/zwavedatabase/1040/image/)


The HS-WD200+ supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

HS-WD200+ is a Z-Wave wall dimmer that’s designed for wireless on-off-dim control of connected dimmable lighting loads.

### Inclusion Information

Put your Z-Wave controller into inclusion mode, tap the paddle of your new HomeSeer dimmer to begin the inclusion process. This will take a few moments to complete.

### Exclusion Information

Put your Z-Wave controller into exclusion mode, tap the paddle of your new HomeSeer dimmer to begin the inclusion process. This will take a few moments to complete.

## Channels

The following table summarises the channels available for the HS-WD200+ -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer | 
| Scene Number | scene_number | scene_number |  | Number | 
| Sets switch mode of operation | config_decimal | config_decimal |  | Number | 
| Normal mode LED colour | config_decimal | config_decimal |  | Number | 
| Status mode LED 1 Colour | config_decimal | config_decimal |  | Number | 
| Sets LED operation (in normal mode) | config_decimal | config_decimal |  | Number | 
| Sets paddle’s load orientation  | config_decimal | config_decimal |  | Number | 
| Status mode LED 2 Colour | config_decimal | config_decimal |  | Number | 
| Status mode LED 3 Colour | config_decimal | config_decimal |  | Number | 
| Status mode LED 4 Colour | config_decimal | config_decimal |  | Number | 
| Status mode LED 5 Colour | config_decimal | config_decimal |  | Number | 
| Status mode LED 6 Colour | config_decimal | config_decimal |  | Number | 
| Status mode LED 7 Colour | config_decimal | config_decimal |  | Number | 
| Status mode LEDs Blink frequency | config_decimal | config_decimal |  | Number | 

### Dimmer
The brightness channel allows to control the brightness of a light.
            It is also possible to switch the light on and off.

The ```switch_dimmer``` channel is of type ```switch_dimmer``` and supports the ```Dimmer``` item and is in the ```DimmableLight``` category.

### Scene Number
Triggers when a scene button is pressed.

The ```scene_number``` channel is of type ```scene_number``` and supports the ```Number``` item.
This channel provides the scene, and the event as a decimal value in the form ```<scene>.<event>```. The scene number is set by the device, and the event is as follows -:

| Event ID | Event Description  |
|----------|--------------------|
| 0        | Single key press   |
| 1        | Key released       |
| 2        | Key held down      |
| 3        | Double keypress    |
| 4        | Tripple keypress   |
| 5        | 4 x keypress       |
| 6        | 5 x keypress       |

### Sets switch mode of operation
0=Normal mode (load status) 1=Status mode (custom status) 

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Normal mode LED colour
Sets the Normal mode LED colour

Possible values: 0-6

0=White, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 1 Colour
LED 1 is the Bottom LED

Possible values: 0-7

0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Sets LED operation (in normal mode)
0= LED ON if load is OFF

1= LED OFF if load is OFF

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Sets paddle’s load orientation 
0 = Top of Paddle turns load ON

1 = Bottom of Paddle turns load ON 

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 2 Colour
Possible values: 0-7

 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 3 Colour
Possible values: 0-7

 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 4 Colour
Possible values: 0-7

 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 5 Colour
Possible values: 0-7

 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 6 Colour
Possible values: 0-7

 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LED 7 Colour
LED 7 is the top LED

 Possible values: 0-7

 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.

### Status mode LEDs Blink frequency
Sets the dimmer Blink frequency for All LEDs in Status mode 

 Possible values: 0, 1-255

0=No blink, 1=100ms ON then 100ms OFF

Generic class for configuration parameter.

The ```config_decimal``` channel is of type ```config_decimal``` and supports the ```Number``` item.



## Device Configuration

The following table provides a summary of the 21 configuration parameters available in the HS-WD200+.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 3 | Bottom LED Operation | Sets the operation of the bottom LED |
| 4 | Orientation | Set paddle load orientation |
| 11 | Remote Ramp Rate | Set dimmer ramp rate for remote control |
| 12 | Local Ramp Rate | Set dimmer ramp rate for local control |
| 13 | Status Mode | Set dimmer display mode |
| 14 | Load Status LED Color | Set the LED color when displaying load status |
| 21 | Status LED 1 Color | Status LED 1 Color (bottom) |
| 22 | Status LED 2 Color | Status LED 2 Color |
| 23 | Status LED 3 Color | Status LED 3 Color |
| 24 | Status LED 4 Color | Status LED 4 Color |
| 25 | Status LED 5 Color | Status LED 5 Color |
| 26 | Status LED 6 Color | Status LED 6 Color |
| 27 | Status LED 7 Color | Status LED 7 Color (top) |
| 30 | Blink Frequency | Set blink frequency when displaying custom status |
| 31 | LED 1 Blink Status | LED 1 Blink Status (bottom) |
| 31 | LED 2 Blink Status | LED 2 Blink Status |
| 31 | LED 3 Blink Status | LED 3 Blink Status |
| 31 | LED 4 Blink Status | LED 4 Blink Status |
| 31 | LED 5 Blink Status | LED 5 Blink Status |
| 31 | LED 6 Blink Status | LED 6 Blink Status |
| 31 | LED 7 Blink Status | LED 7 Blink Status (top) |
|  | Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |

### Parameter 3: Bottom LED Operation

Sets the operation of the bottom LED

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Bottom LED ON if load is OFF |
| 1 | Bottom LED OFF if load is OFF |

The manufacturer defined default value is ```1``` (Bottom LED OFF if load is OFF).

This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```.


### Parameter 4: Orientation

Set paddle load orientation

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Top of Paddle turns load ON |
| 1 | Bottom of Paddle turns load ON |

The manufacturer defined default value is ```0``` (Top of Paddle turns load ON).

This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```.


### Parameter 11: Remote Ramp Rate

Set dimmer ramp rate for remote control

Values in the range 0 to 90 may be set.

The manufacturer defined default value is ```3```.

This parameter has the configuration ID ```config_11_1``` and is of type ```INTEGER```.


### Parameter 12: Local Ramp Rate

Set dimmer ramp rate for local control

Values in the range 0 to 90 may be set.

The manufacturer defined default value is ```3```.

This parameter has the configuration ID ```config_12_1``` and is of type ```INTEGER```.


### Parameter 13: Status Mode

Set dimmer display mode

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Load Status |
| 1 | Custom Status |

The manufacturer defined default value is ```0``` (Load Status).

This parameter has the configuration ID ```config_13_1``` and is of type ```INTEGER```.


### Parameter 14: Load Status LED Color

Set the LED color when displaying load status

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | White |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |

The manufacturer defined default value is ```0``` (White).

This parameter has the configuration ID ```config_14_1``` and is of type ```INTEGER```.


### Parameter 21: Status LED 1 Color

Status LED 1 Color (bottom)

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_21_1``` and is of type ```INTEGER```.


### Parameter 22: Status LED 2 Color

Status LED 2 Color

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_22_1``` and is of type ```INTEGER```.


### Parameter 23: Status LED 3 Color

Status LED 3 Color

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_23_1``` and is of type ```INTEGER```.


### Parameter 24: Status LED 4 Color

Status LED 4 Color

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_24_1``` and is of type ```INTEGER```.


### Parameter 25: Status LED 5 Color

Status LED 5 Color

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_25_1``` and is of type ```INTEGER```.


### Parameter 26: Status LED 6 Color

Status LED 6 Color

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_26_1``` and is of type ```INTEGER```.


### Parameter 27: Status LED 7 Color

Status LED 7 Color (top)

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off |
| 1 | Red |
| 2 | Green |
| 3 | Blue |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
| 7 | White |

The manufacturer defined default value is ```0``` (Off).

This parameter has the configuration ID ```config_27_1``` and is of type ```INTEGER```.


### Parameter 30: Blink Frequency

Set blink frequency when displaying custom status

The following option values may be configured, in addition to values in the range 0 to 255 -:

| Value  | Description |
|--------|-------------|
| 0 | No Blink |
| 1 | Blink 100ms ON, 100ms OFF |
| 2 | Blink 200ms ON, 200ms OFF |
| 3 | Blink 300ms ON, 300ms OFF |
| 4 | Blink 400ms ON, 400ms OFF |
| 5 | Blink 500ms ON, 500ms OFF |

The manufacturer defined default value is ```0``` (No Blink).

This parameter has the configuration ID ```config_30_1``` and is of type ```INTEGER```.


### Parameter 31: LED 1 Blink Status

LED 1 Blink Status (bottom)

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000001``` and is of type ```INTEGER```.


### Parameter 31: LED 2 Blink Status

LED 2 Blink Status

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000002``` and is of type ```INTEGER```.


### Parameter 31: LED 3 Blink Status

LED 3 Blink Status

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000004``` and is of type ```INTEGER```.


### Parameter 31: LED 4 Blink Status

LED 4 Blink Status

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000008``` and is of type ```INTEGER```.


### Parameter 31: LED 5 Blink Status

LED 5 Blink Status

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000010``` and is of type ```INTEGER```.


### Parameter 31: LED 6 Blink Status

LED 6 Blink Status

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000020``` and is of type ```INTEGER```.


### Parameter 31: LED 7 Blink Status

LED 7 Blink Status (top)

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Solid |
| 1 | Blink |

The manufacturer defined default value is ```0``` (Solid).

This parameter has the configuration ID ```config_31_1_00000040``` and is of type ```INTEGER```.

### Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -:
| Value  | Description |
|--------|-------------|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |

This parameter has the configuration ID ```switchall_mode``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The HS-WD200+ supports 2 association groups.

### Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Lifeline association only supports the "manual reset" event.

Association group 1 supports 5 nodes.

### Group 2: Companion Sync

Any device added to group 2 will be controlled. This allows other WX200 devices to used as companion switches. LEDS will be kept in sync.

Association group 2 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3| Linked to BASIC|
| COMMAND_CLASS_SWITCH_ALL_V1| |
| COMMAND_CLASS_SCENE_ACTIVATION_V1| |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| |
| COMMAND_CLASS_CENTRAL_SCENE_V3| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_VERSION_V2| |

### Documentation Links

* [HS-WD200+ Product Manual](https://opensmarthouse.org/zwavedatabase/1040/reference/HS-WD200-Manual-5a.pdf)
* [HS-WD200+ Product Manual (Updated)](https://opensmarthouse.org/zwavedatabase/1040/reference/HS-WS200-Manual-v7a.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/1040).