- default value is the same as before patch
- system_stm32f2xx.c file is copied to family level with all other ST cube files
- specific clock configuration is now in a new file: system_clock.c (target level)
In this commit, the analogin_s structure is moved to commonn_objects.h file
to limit the duplicaion.
The ADC handle is moved from a global variable to a struct member of the
analogin object. This allows multiple ADC instances to work correctly.
Note that State needs to be explicitely set to HAL_ADC_STATE_RESET
because the object is not zero initialized.
TXE indicates that a byte can be written to UART register for sending,
while TC indicates that last byte was completely sent. So the TXE flag
can be used in case of interrupt based Serial communication, to allow
faster and efficient application buffer emptying.
Also TXE flag will be erased from the interrupt when writing to register.
In case there is nothing to write in the register, the application is
expected to disable the interrupt.
The RXNE flag is getting cleared when reading Data Register so it should
not be cleared here. Especially in case of high data rate, another byte of
data could have received during irq_handler call and clearing the flag
would read and discard this data which would be lost for application.
Moving some code in common to be able to manage several ADC instances,
or several channels of an instance.
The change involves:
- moving dac_s structure definition to common_object.h
- create TARGET_STM/analogout_api.c and move fully common analog_out
functions in there
- rename analogout_api.c of each target family into analogout_device.c
to keep platform specific code
- update analogout_device.c to rely on obj->handle and obj->channel
- align analogout_init function as much as possible between families in
analogout_device.c files
This commit implements a SPI mode which will offer better performance
thanks to usage of Lower Layer API which use fewer registers access,
at the cost of lower robustness (no error management).
Remove HAL_Init and related code from SystemInit and move it to
mbed_sdk_init. The function SystemInit is called early in the boot
sequence before RAM is initialized or the VTOR is setup, so it should
not be used to perform the HAL initialization.
This fixes crashes due the vector table being used before it has been
relocated.
Note that this could have side effects on the application as it would
not be aware that data has been missed. This may be later solved by
adding an error management parameter to the Serial API in mbed.
The advantage is that the serial link can work again.
As reported in issue #4214, there are seen issues seen first on
NUCLEO_F103RB in case of successive Reads of 1 byte at a time.
This issue is due to a wrong state management in the end of read sequence.
Also F1 i2c driver was not fully aligned to others, which is updated here.
For STM32 targets using a 32-bit timer for the microsecond ticker, the
driver did not properly handle timestamps that are in the past. It
would just blindly set the compare register to the requested timestamp,
resulting in the interrupt being serviced up to 4295 seconds late
(i.e. after the 32-bit timer counts all the way around to hit the
timestamp again).
This problem can easily be reproduced by creating a Timeout object
then calling the timeout's attach_us() member function to attach a
callback with a timeout of 0 us. The callback will not get called for
over 2147 seconds, and possibly up to 4295 seconds late if no other
microsecond ticker events are getting scheduled in the meantime.
Now, after the compare register has been set, the timestamp is checked
against the current time to see if the timestamp is in the past, and
if so, the compare event is manually set.
NOTE: By checking if the timestamp is in the past after configuring the
capture register, we ensure proper handling in the case where the timer
updates past the timestamp while setting the capture register.
Reworked the serial_format() function for STM32F0x
devices to take the format in the form:
data_bits - parity - stop_bits
E.g. 8 - N - 1
where data_bits exclude the parity bit.
Added a case for 7 bits data as at least the chips
STM32F0x1/STM32F0x2/STM32F0x8 support 7 bits data.
Consolidated serial_format() and uart_init()
functions into a general TARGET_STM serial_api.c
file since the functions are common to all STM targets.
Fixes#4189
When we want to activate USE_FULL_ASSERT macro in STM32 CUBE, there is a
need to have the assert map to MBED.
The easiest way to have this definition in a single place for all STM32
HAL and LL files using it, is to add a specific header file where the
porting to MBED is done.
If you are using Ethernet, and not SPI Arduino pins:
=> keep your board with the default configuration
If you are using SPI Arduino pins, and not Ethernet:
=> you should remove the JP6 bridge on the front side of the board
If you need SPI Arduino and Ethernet:
=> you have to patch the NUCLEO board on the back side: set solder bridge SB121 to off, and SB122 to on
=> D11 is no more connected to PA_7 but to PB_5
=> overwrite d11_configuration config value in json file
Revert HRM1017 file source deletion
Added in small comment next to additions
Added mapping to BTN-labelled switches
Added mapping to USER_BUTTON-labelled switches
Undo incorrect mapping to SWIO pin in NORDIC target
Before this patch, many warnings like below were generated
during compilation with ArmCC
[Warning] lwip_ethernet.h@57,0: #3135-D: attribute does not apply to any entity
This happens here as ``--gnu`` option of ArmCC is being used, which
enables the GNU compiler extensions that the ARM compiler supports.
This is solve by adding a extra check on __CCARM .
Jimmy Brisson
jeromecoutant
Laurent MEUNIER
Anna Bridge
Martin Kojtal
Russ Butler
Sam Grove
Bradley Scott
Bartek Szatkowski
Francisco J. Manno
adustm
Michel Jaouen
Kevin Gilbert
Mihail Stoyanov