Since target specific ticker drivers are not ready also features which uses ticker in upper layers may not work correctly and tests for these features.
We need to disable also failing higher level ticker related tests (by adding check if DEVICE_USTICKER symbol is available and raise #error [NOT_SUPPORTED] if not).
Note:
tests-mbed_drivers-rtc is new and uses us ticker to perform a delay.
count_ticks() function counts ticker ticks elapsed during execution of N cycles of empty while loop.
In current version N value (cycles) is given as volatile paramater in order to disable possible compiler optimalisation.
There was a problem with measured time on different compilers and additionally results on ARM compiler were unexpected (the difference beetween measured elapsed ticks for the same number of cycles was to large). This might be caused by the memory access in order to store updated variable in memory. To fix this issue given numer of cycles has been stored into register and register is decremented (no memory access).
With this fix count_ticks(NUM_OF_CYCLES, 1) call returns 2500 +/-1 for us ticker ticks using each compiler (K64F).
On some platforms (e.g. K64F) different counters are used for time measurement and interrupt generation.
Because of that we should relax interrupt test case and give additional time before checking if interrupt handler has been executed.
Since according to the ticker requirements min acceptable counter size is 12 bits (low power timer) for which max count is 4095, then all test cases must be executed in this time window.
HAL ticker layer handles overflow and it is not handled in the target ticker drivers.
Low power ticker time counter is created based on RTC which is driven by 32KHz clock. Additional low power timer is used to generate interrupts.
We need to adapt driver to operate on ticks instead of us.
Perform the following updates:
- provide lp ticker configuration: 32KHz/32 bit counter.
- lp_ticker_init() routine disables lp ticker interrupts .
- adapt the driver functions to operate on ticks instead us.
- adapt comments.
- add us_ticker_free() routine.
The intention was to use ticker_overflow_delta equal to 0 for low power ticker tests and ticker_overflow_delta equal to 50 for high frequency ticker tests. Current implementation is invalid since for devices which provide LOW_POWER_TIMER feature delta is equal to 0 and for devices without this feature delta is equal 50.
Current version:
The function ticker_init resets the internal count and disables the ticker interrupt.
Proposed version:
The function ticker_init allows the ticker to keep counting and disables the ticker interrupt.
This is a result of the following discussion:
https://github.com/ARMmbed/mbed-os/pull/5233#pullrequestreview-86677815
Since target specific ticker drivers are not ready also features which uses ticker in upper layers may not work correctly and tests for these features.
We need to disable also failing higher level ticker related tests (by adding check if DEVICE_USTICKER symbol is available and raise #error [NOT_SUPPORTED] if not).
I implemented the SLEEP feature for Rnesas mbed boards.
The mainly changing is here.
- hal_sleep()
To satisfy the mbed specificationm, I implemented this function newly by using "sleep" that is one of low power mode that is incorporated in our hardware(RZ_A1).
In the "sleep", peripheral and memory state are maintained, and the peripherals continue to work and can generate interrupts.
- hal_deepsleep()
To satisfy the mbed specificationm, I implemented this function newly by combined using "sleep" and "module standby" that is the low power mode that is incorporated in our hardware(RZ_A1).
The "module standby" is peripheral module's powerdown.
Also in case of our "module standby", it need to read register as dummy when access to each register.
These boards will be re-enabled when sleep driver for them is ready.
Note:
This operation is done by removing "SLEEP" feature from target's "device_has" list (in targets.json config file).
For NRF52_DK removing of "SLEEP" feature causes some timing issues which have influence on tests. In order to successfully disable this board we need to disable also related features like "USTICKER", "LOWPOERTIMER" and slightly modify ticker tests, so they will not be executed if usticker support is not available (by default all targets support us ticker).
Sleep - within 10us
Deepsleep - within 10ms
Note about mbed boards with interface, moved to lpc176x, as they are target related,
should be documented in the target documentation.
The tests will come as separate PR, to conform to this updates to sleep API.
There is a configuration problem with UBLOX_C027 cellular because of missing
LWIP memory configuration for the target.
Added configuration for LPC1768, LPC4088, LPC4088_DM targets and changed
NXP to more specific LPC546XX.
- Set network stack to store event queue so that mbed::mbed_event_queue() call
is not needed every time call_in() is called
- Added dns state variables and enum (states are: created, initiated and cancelled)
- Corrected DNS response handling so that if DNS server returns that host name is
unknown the DNS query is not tried again
- Reorder mutexes in nsapi_dns_query_multiple_async()
- Created nsapi_dns_query_async_initiate_next() function to initiate the next
DNS query from the queue after delete of previous query
- Added dsn_timer_running variable to supervise DNS timer start/stop
- Changed cancel function to only mark query as deleted and moved deletion
to timer function. This allows to run socket close on DNS thread
- Added new nsapi error NSAPI_ERROR_TIMEOUT for DNS (and other) timeouts
Bartek Szatkowski
Przemyslaw Stekiel
Steven Cartmell
Russ Butler
TomoYamanaka
Martin Kojtal
adbridge
Cruz Monrreal
Marcus Chang
Martin Kojtal
Marc Emmers
Mika Leppänen
Kari Haapalehto
Alan Chuang
Seppo Takalo