Following
Merge pull request #4063 from LMESTM/17q2_L4_bootloader
the NUCLEO_L476RG binairies could not boot anymore.
The change done in #4063 was derived from work on NUCLEO_L429ZI target
which supports uvisor. The VECTORS defintiion is introduced as part of
uvisor support and requires further changes in ld file which were missing.
As uvisor is not considered yet, we remove VECTORS for now and will
introduce only when needed.
Remove HAL_Init and related code from SystemInit and move it to
mbed_sdk_init. The function SystemInit is called early in the boot
sequence before RAM is initialized or the VTOR is setup, so it should
not be used to perform the HAL initialization.
This fixes crashes due the vector table being used before it has been
relocated.
This reduces the number of loads inside of the .data copy loop by 3 by using one more register. It should work on any STM32 with at least 5 general-purpose registers. If only 4 are available, then 1 load could still be removed from the original implementation.
1. Add startup code and linker script for IAR and
GCC_ARM compilers.
2. Enable IAR and GCC_ARM compilers in targets.json.
Change-Id: I742a89ae73a4e5ede980a8af0821c3f0e5a461ef
Signed-off-by: Mate Toth-Pal <mate.toth-pal@arm.com>
Based on lwip_ethernetif.c skeleton file,
use init, receive and transfer
functionality of SMSC9220 Ethernet driver
for the lightweight IP stack.
Receive mechanism is interrupt driven.
HW buffer sizes:
Tx = 4608 bytes (MTU)
Rx = 10560 bytes
lwIP fine tuning:
mbed-os/features/FEATURE_LWIP/lwip-interface/lwip/src/include/lwip/opt.h
Change-Id: I0ea95650c65fb32cafb5c2d3dde11420c61dba66
Signed-off-by: Gabor Kertesz <gabor.kertesz@arm.com>
- Creates new target in targets.json
- Creates device specific files under ARM_SSG/CM3DS_MPS2 directory
- Driver layer files under CM3DS_MPS2 are based on Beid target
- Device specific files under CM3DS_MPS2/device are based on CMSIS_5 and Beetle
Change-Id: I29ea7a7f42b11cf25b516cce4b9255ab828ca019
Signed-off-by: Tamas Kaman <Tamas.Kaman@arm.com>
Signed-off-by: Marc Moreno <marc.morenoberengue@arm.com>
Define CMSIS_VECTAB_VIRTUAL for the M0 targets which have a
corresponding driver. The only M0 target missing this is the LPC4330_M0
which is not part of the 2 or 5 release.
Restore cmsis_nvic (cmsis_nvic.c and cmsis_nvic.h) files for the
implementations which use a mechanism other than the VTOR to set
interrupts. These are vendor specific and were done for M0 devices
which do not have a VTOR.
Note - There were two cmsis_nvic files which did not use the VTOR that
which not restored in this patch. This is because these targets were
not M0 devices and could use the new unified implementation instead.
These files are:
targets\TARGET_ARM_SSG\TARGET_MPS2\TARGET_MPS2_M0P\device\cmsis_nvic.c
targets\TARGET_ONSEMI\TARGET_NCS36510\device\cmsis_nvic.c
Note - cmsis_nvic.c and cmsis_nvic.h were initial removed in
(and restored from) the commit:
b97ffe8fdc -
"CMSIS5: Replace target defined NVIC_Set/GetVector with CMSIS implementation"
Note that this could have side effects on the application as it would
not be aware that data has been missed. This may be later solved by
adding an error management parameter to the Serial API in mbed.
The advantage is that the serial link can work again.
The use of mktime was causing a fault when called in interrupt handler because on GCC it lock the mutex protecting the environment, To overcome this issue, this patch add dedicated routine to convert a time_t into a tm and vice versa.
In the process mktime has been optimized and is now an order of magnitude faster than the routines present in the C library.
The Ameba RTC driver converts time_t to
second/minute/hour/day/month/year in rtc_write and back to time_t in
rtc_read. Replace this with an implementation which uses time_t
directly.
* Make memory sections configurable in linker files
* Dynamically determine vector location in flash for NVIC relocation
* Advertise bootloader support in targets.json
When using ARM Compiler 5, the RTX config hard-coded the heap and stack
sizes to specific values. This prevented the RTX HAL from dynamically
allocating unused memory as heap space.
Specifically, the HEAP_START define prevents this logic in RTX_CM_lib.h
from activating. The rest of the defines are also set in that header,
and should be removed from here.
* Using PinName as bitfield doesn't work without warnings, since NC
needs all 32 bits to be represented.
* lp_ticker should not be freed when interrupt is disabled, since this
will kill the timebase.
Add MBED_APP_START and MBED_APP_SIZE to the linker scripts
so the start and size of an image can be specified. This allows the
ROM to be split into a bootloader region and an application region.
Fix vector table
The address of the vector table is hardcoded to the start of flash.
This patch updates make it properly handle updating the VTOR with
a bootloader.
When initializing the RTC on Kinetis devices, handle the case where
the time overflow interrupt is pending and the case where the time
alarm flag is pending. These flags persist across reset and if not
handled will cause a crash when powering up the low power ticker.
This problem manifested as a lp_ticker test failure on the K22F and
K64F on CI only when running a nightly. This problem has been present
but was made obvious by PR #4094 which configures all tickers to
interrupt at least every MBED_TICKER_INTERRUPT_TIMESTAMP_MAX_DELTA
(~31 minutes). This caused the RTC alarm to fire 31 minutes after the lp_ticker
or lp_timeout test and caused the next run of the lp_ticker test to
crash on boot.
TimMasterHandle.Instance initialization can be removed from here,
because it will either have been already done previously,
or it will be done in the us_ticker_init() call immediately below.
Following previous fixes on 16 tickers handling, the overflow flag
condition will not happen anymore, so the work-around in place is
not needed anymore
This commit simplifies ticker interrupt set function and handler.
There were issues around the 16 bits timer wrap-around timing as we were
aligning interrupts with wrap-around limits (0xFFFF) and then reading
TIM_MST->CNT again in timer_update_irq_handler which could lead
to crossing case with the wrap-around (TIM_FLAG_UPDATE) case.
Now we're using the 16 lower bits of the timestamp as the reference from
using in set_compare and never changing it. There is also no need to set
comparator again in timer_update_irq_handler. This is more robust and
also more efficient.
Move to a single more reliable implementation of us_ticker_read()
There were historically 2 versions of us_ticker_read() implementation.
The one removed here was not reliable because us_ticker_read() can be
called in interrupt context which means that TIM_MST->CNT would have
wrapped around while SlaveCounter is not yet updated. So there is a need
to check the TIM_FLAG_UPDATE inside this function, which was not done in
the implementation that is removed here.
There is an easy default implementation of spi_master_block_write that
just calls spi_master_write in a loop, so the default implementation
of spi_master_block_write has been added to all targets.
Martin Kojtal
Yuguo Zou
Andreas Larsson
Laurent MEUNIER
Russ Butler
Mahadevan Mahesh
jeromecoutant
bcostm
Fahrzin Hemmati
Sam Grove
Jimmy Brisson
mattot01
Tamas Ban
gabker01
Tamas Kaman
Aksel Skauge Mellbye
Kevin Gilbert
Andrzej Puzdrowski
Vincent Coubard
Steven Cooreman
kl-cruz
Anna Bridge