This PR is to fix the issues in LwIP for AutoIP which is required for passing Bonjour Conformance Test for mDNS. Following gives the summary of the changes/fixes added.
Changes:
1. Following issues are fixed in LwIP for AutoIP.
- Fixed bug in max conflict rate limiting: According to RFC section RFC 3927 Section 2.2.1 conflict probe interval should be increased to 60 seconds, once conflict count reaches after MAX_CONFLICTS (i.e., 10) counts. The initial value of 'autoip->tried_llipaddr' is 0. Hence the probe interval (i.e., autoip->ttw) should be increased to 60 secs when 'autoip->tried_llipaddr >= MAX_CONFLICTS'
- Added code to free 'autoip' client in autoip_stop() API: New 'autoip' client is allocated in autoip_start() API, and the client is not freed during autoip_stop(). This would result in memory leak, if not freed. Updated autoip_stop() API to take care of releasing the memory allocated for 'autoip' client.
2. Introduced a configurable macro "MBED_CONF_LWIP_DHCP_TIMEOUT" in "lwipopts.h" to configure DHCP timeout based on the usecase requirement. For example: bonjour conformance test would need a DHCP timeout value which is grater than 320 secs to run mDNS probing test to verify protocol compilance of the implementation.
Tested the fixes using Bonjour Conformance Test tool Version 1.5.0 for IPv4. It has successfully passed Bonjour Conformance Test.
- Reduce heap footprint by storing only single block when receiving a blockwise message.
* User is now responsible of freeing the data by calling sn_coap_protocol_block_remove() and must not free the payload separately.
- Bug fix: Request blockwise transfer if incoming payload length is too large and when it comes without block indication.
These provide information to allow Cypress graphical configuration tools
to avoid conflicting usage of hardware resources which are managed by
firware included with the BSP.
When flashing a binary STLink won't skip writing padding which happens
to be the same value as flash's erase value. STM32L4 based targets
have an additional 8-bit of embedded ECC for each 64-bit word of data.
The initial value, when a sector is erased, for the ECC bits is 0xFF.
When you write the erase value to a given address these bits gets
modified to something different due to the ECC algoritm in use. The
visible bits are intact but difference in ECC value prevents flipping
any 1's to 0's. Only way to proceed is to erase the whole sector.
tuples will be useful for things like `mbed::Event` and
`mbed::Callback` - storing parameter packs from variadic templates.
Create a C++14(ish) `<tuple>` for ARMC5, and a `<mstd_tuple>` that
adds `apply` and `make_from_tuple` from C++17.
In custom wiring, there can be a power pin to power on/off the modem. This
commit supports it and allows for the following configurations:
- power pin name
- power pin polarity
- power on/off delay time
New ATHandler functions taken into use for rest of the targets (BG96 was updated initially) to reduce code size. This means basically that new functions using variadic list approach are taken into use and with those one can usually write AT commands in single line instead of multiple lines.
Only internal changes and API's are not modified.
Changes:
1. Following issues are fixed in LwIP for AutoIP.
a) Fixed bug in max conflict rate limitting.
- According to RFC section RFC 3927 Section 2.2.1 conflict probe interval
should be increased to 60 seconds, once conflict count reaches after
MAX_CONFLICTS (i.e., 10) counts.
- The initial value of 'autoip->tried_llipaddr' is 0. Hence the probe
interval (i.e., autoip->ttw) should be increased to 60 secs
when 'autoip->tried_llipaddr >= MAX_CONFLICTS'
b) Added code to free 'autoip' client in autoip_stop() API.
- New 'autoip' client is allocated in autoip_start() API, and the client
is not freed during autoip_stop(). This would result in memory leak
if not freed.
- Updated autoip_stop() API to take care of releasing the memory allocated
for 'autoip' client.
2. Introduced a configurable macro "MBED_CONF_LWIP_DHCP_TIMEOUT" in "lwipopts.h"
to configure DHCP timeout based on the usecase requirement. For example:
bonjour conformance test would need a DHCP timeout value which is grater than
320 secs to run mDNS probing test to verify protocol compilance of the implementation.
[Warning] tcm_heap.c@70,18: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'MemChunk * {aka struct _MemChunk *}' [-Wformat=]
[Warning] tcm_heap.c@70,28: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'MemChunk * {aka struct _MemChunk *}' [-Wformat=]
Signed-off-by: Tony Wu <tonywu@realtek.com>
Qinghao Shi
Mahesh Mahadevan
Marcelo Salazar
Martin Kojtal
Antti Yli-Tokola
Sathish Kumar Mani
Arto Kinnunen
Ryan Morse
Malavika Sajikumar
Shuopeng Deng
Kyle Kearney
Yogesh Pande
Jammu Kekkonen
Dominika Maziec
Kevin Bracey
Chun-Chieh Li
Jarkko Paso
Antti Kauppila
Tony Wu