Due to buggy flow control logic in the UARTE, the stop signal
is not being set as it is supposed to when the the module is
not ready to receive data.
This commit signals the sender to halt transmitting when a DMA
buffer is full and only continue again when the atomic FIFO
buffer has been emptied. This allows platforms with hardware
flow control to minimize all buffers and rely on flow control
instead.
The preprocessor based macro check #if evaluates all
enums as 0 and hence the code does not get compiled.
Since move this to a runtime check where the pin variable
can be correctly evaluated.
Delete mbed_overrides.c as it has a target specific mbed_sdk_init() to
resolve linking problem.
This is a follow on patch to:
https://github.com/ARMmbed/mbed-os/pull/8046
While investigating the RX issue on NRF52_DK after SDK 14 updates,
it is observed that the RX FIFO doesn't get filled up, when the
flow control is disabled. Hence the readable never returns true.
If using Serial interface, the stdio file handles (0, 1, 2) get opened.
This results in configuring the flow control for STDIO, and it is observed
that the RX FIFO gets filled.
However, if RawSerial is used, the STDIO file handles
don't get opened. During the debug process it was observed that if the
flow control is configured once and then set to disabled, RX worked
as expected.
Alternative to this approach is that user application specifically
enables flow control as done in mbed's Greentea test suite. See https://goo.gl/r8nBYH
See https://goo.gl/8VB2qg step 14 for _initio's description.
See test code to reproduce the issue and test fix here: https://goo.gl/AQU1xG
Description
The change in behavior with NRF52's UART RX is documented here. #6891
This change is a fix for the above issue.
While investigating the RX issue on NRF52_DK after SDK 14 updates,
it is observed that the RX FIFO doesn't get filled up, when the
flow control is disabled. Hence the readable never returns true.
If using Serial interface, the stdio file handles (0, 1, 2) get opened.
This results in configuring the flow control for STDIO, and it is observed
that the RX FIFO gets filled.
However, if RawSerial is used, the STDIO file handles
don't get opened. During the debug process it was observed that if the
flow control is configured once and then set to disabled, RX worked
as expected.
Alternative to this approach is that user application specifically
enables flow control as done in mbed's Greentea test suite. See https://goo.gl/r8nBYH
See https://goo.gl/8VB2qg step 14 for _initio's description.
See test code to reproduce the issue and test fix here: https://goo.gl/AQU1xG
Description
The change in behavior with NRF52's UART RX is documented here. #6891
This change is a fix for the above issue.
--legacyalign, --no_legacyalign are deprecated from ARMC6 compiler, in order to
remove deprecated flags all linker files (GCC and IAR as well to have uniformity)
should strictly align to 8-byte boundary
There are scenarios where putc is called within a critical section, e.g
to log ASSERTs in early initialization code. The interrupts being
disabled here prevents the handlers for the UARTE from executing.
This breaks the tx_in_progress flag based approach. The tx_in_progress
never gets reset. Poll on the TXDRDY instead.
It can be recreated with a simple program as shown here:
*************** Current Behavior ****************
++ MbedOS Error Info ++
Error Status: 0x80FF0100 Code: 256 Module: 255
Error Message: F
************** With Fix *************************
++ MbedOS Error Info ++
Error Status: 0x80FF0100 Code: 256 Module: 255
Error Message: Fatal Run-time error
Location: 0x2C0A9
Error Value: 0x0
Current Thread: Id: 0x20005520 Entry: 0x30EBF StackSize: 0x1000 StackMem: 0x20004520 SP: 0x20005490
For more info, visit: https://armmbed.github.io/mbedos-error/?error=0x80FF0100
-- MbedOS Error Info --
nrf failure at .\main.cpp:22
***************************************************
This PR provides implementation of ticker_free() function for the following boards:
ARCH_PRO
EV_COG_AD3029LZ
EV_COG_AD4050LZ
K22F
K64F
K82F
KW24D
KW41Z
LPC546XX
NRF51_DK
NRF52_DK
NUCLEO_F207ZG
NUCLEO_F401RE
NUCLEO_F429ZI
NUCLEO_F746ZG
REALTEK_RTL8195AM
i2c_api implementation for NRF52 does a disable() followed by uninit().
The uniinit() implementation in NRF drivers layer makes another call to
disable. This throws off the state of the I2C instance leading to an
assert. Since the disable is only invoked from the I2C API layer for
Nordic, remove this redundant call.
Signed-off-by: Naveen Kaje <Naveen.Kaje@arm.com>
The ITM must be initialized before the SoftDevice, but due to the
lazy initialization in C++ on (at least) GCC the ITM init call
might happen too late.
This commit moves the initialization code into the NRF52 system
startup file.
Marcus Chang
Naveen Kaje
Ashok Rao
Deepika
Andrew Leech
Maciej Bocianski
Jammu Kekkonen
Yossi Levy
Martin Kojtal
Martin Kojtal
Senthil Ramakrishnan
Cruz Monrreal
Jiwon Yune
Przemyslaw Stekiel
Jiwon Yune
RFulchiero