openhab-docs/_addons_bindings/zwave/doc/shelly/wavepmmini_0_0.md

layout	title
documentation	Wave PM Mini - ZWave

{% include base.html %}

Wave PM Mini Z-Wave smart power meter, 1 channel 16 A

This describes the Z-Wave device Wave PM Mini, manufactured by Shelly with the thing type UID of shelly_wavepmmini_00_000.

The device is in the category of Battery, defining Batteries, Energy Storages.

The Wave PM Mini supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

The Device is a small form factor smart power meter, which allows remote monitoring of an electric appliance's power consumption with a load of up to 16 A.

Inclusion Information

1. Connect the Device to a power supply.
2. Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network.
3. Enable add/remove mode on the gateway.
4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.
5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode.
6. The blue LED will be blinking in Mode 2 during the adding process.
7. The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

Exclusion Information

1. Connect the Device to a power supply.
2. Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave® network.
3. Enable add/remove mode on the gateway.
4. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue.
5. Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the LEARN MODE.
6. The blue LED will be blinking in Mode 2 during the removing process.
7. The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave® network.

Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode.

General Usage Information

Channels

The following table summarises the channels available for the Wave PM Mini -:

Channel Name	Channel ID	Channel Type	Category	Item Type
Electric meter (kWh)	meter_kwh	meter_kwh	Energy	Number
Electric meter (watts)	meter_watts	meter_watts	Energy	Number
Reset the total power consumption	meter_reset	meter_reset	Energy	Switch
Alarm (heat)	alarm_heat	alarm_heat	Fire	Switch
Alarm (power)	alarm_power	alarm_power	Energy	Switch

Electric meter (kWh)

Indicates the energy consumption (kWh).

The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Electric meter (watts)

Indicates the instantaneous power consumption.

The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

Reset the total power consumption

Reset the meter.

The meter_reset channel is of type meter_reset and supports the Switch item and is in the Energy category.

Alarm (heat)

Indicates if a heat alarm is triggered.

The alarm_heat channel is of type alarm_heat and supports the Switch item and is in the Fire category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value	Label
OFF	OK
ON	Alarm

Alarm (power)

Indicates if a power alarm is triggered.

The alarm_power channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value	Label
OFF	OK
ON	Alarm

Device Configuration

The following table provides a summary of the 6 configuration parameters available in the Wave PM Mini. Detailed information on each parameter can be found in the sections below.

Param	Name	Description
36	O (O1) Power report on change	Minimum change in consumed power that will result in sending a new report to the gateway.
39	Minimum time between reports (O) O1	Minimum time that must elapse before a new power report on O (O1) is sent to the gateway.
120	Factory Reset	Reset to factory default settings and removed from the Z-Wave network
201	Serial Number 1	Part of device’s serial number.
202	Serial Number 2	Part of device’s serial number.
203	Serial Number 3	Part of device’s serial number.

Parameter 36: O (O1) Power report on change

Minimum change in consumed power that will result in sending a new report to the gateway. 0 - reports are disabled
1-100 (1-100%) - change in power

NOTE: Regardless of the power consumption change in percentage, the report will not be sent more frequently than defined by Parameter No. 39. Values in the range 0 to 100 may be set.

The manufacturer defined default value is 50.

This parameter has the configuration ID config_36_1 and is of type INTEGER.

Parameter 39: Minimum time between reports (O) O1

Minimum time that must elapse before a new power report on O (O1) is sent to the gateway. 0 - reports are disabled
1-120 (1-120s) - report interval

NOTE: This Parameter is in relation to Parameter No. 36.

NOTE: Setting the value to less than 30s can cause the Z-Wave network congestion state (slow Device response and decreased network stability). Values in the range 0 to 120 may be set.

The manufacturer defined default value is 30.

This parameter has the configuration ID config_39_1 and is of type INTEGER.

Parameter 120: Factory Reset

Reset to factory default settings and removed from the Z-Wave network 0 - Don’t do Factory reset
1 - Do the Factory resetThis is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_120_1 and is of type INTEGER.

Parameter 201: Serial Number 1

Part of device’s serial number. This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 0 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_201_4 and is of type INTEGER. This is a read only parameter.

Parameter 202: Serial Number 2

Part of device’s serial number. This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 0 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_202_4 and is of type INTEGER. This is a read only parameter.

Parameter 203: Serial Number 3

Part of device’s serial number. This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 0 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_203_4 and is of type INTEGER. This is a read only parameter.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.

Technical Information

Endpoints

Endpoint 0

Command Class	Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_METER_V3
COMMAND_CLASS_TRANSPORT_SERVICE_V1
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_SUPERVISION_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_ALARM_V8
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_INDICATOR_V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_SECURITY_V1
COMMAND_CLASS_SECURITY_2_V1

Documentation Links

• Shelly Wave PM Mini user guide

---

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.