7.2 KiB
| layout | title |
|---|---|
| documentation | PSR03-1C - ZWave |
{% include base.html %}
PSR03-1C Panic Button
This describes the Z-Wave device PSR03-1C, manufactured by Philio Technology Corp with the thing type UID of philio_psr031c_00_000.
The device is in the category of Battery, defining Batteries, Energy Storages.
The PSR03-1C supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The PSR03-1C does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
Overview
Inclusion Information
- Put the Z-Wave Controller in inclusion mode.
2. Press panic key three times within 1.5 seconds to enter inclusion mode.
- After successful inclusion, the device will wake to receive the
setting command from Z-Wave Controller in about 20 seconds.
Exclusion Information
-
Put the Z-Wave Controller in exclusion mode.
-
Press panic key three times within 1.5 seconds to enter exclusion mode.
3. Node ID has been excluded.
Wakeup Information
The PSR03-1C does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
General Usage Information
Channels
The following table summarises the channels available for the PSR03-1C -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Alarm (emergency) | alarm_emergency | alarm_emergency | Alarm | Switch |
| Battery Level | battery-level | system.battery_level | Battery | Number |
Alarm (emergency)
Indicates Police, Fire, or Medical services should be contacted.
The alarm_emergency channel is of type alarm_emergency and supports the Switch item and is in the Alarm category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | EMERGENCY |
| OFF | OK |
Battery Level
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
Device Configuration
The following table provides a summary of the 1 configuration parameters available in the PSR03-1C. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 10 | Auto Report Battery Time | Auto Report Battery Time |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
Parameter 10: Auto Report Battery Time
Auto Report Battery Time The interval time for auto report the battery level. 0 means turn off auto report battery. Each tick means 30 minutes. The default value is 12(6 hours). Values in the range 0 to 127 may be set.
The manufacturer defined default value is 12.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Wakeup Interval
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
Wakeup Node
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The PSR03-1C supports 1 association group.
Group 1: Emergency Alarm
Emergency Alarm
Association group 1 supports 4 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V4 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SECURITY_V1 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.