OpenHAB
/
openhab-docs
mirror of https://github.com/openhab/openhab-docs.git
1
0
Fork 0
Code Issues Projects Releases Wiki Activity
openhab-docs/_addons_bindings/zwave/doc/lscontrol/es861c_0_0.md

7.1 KiB
Raw Permalink Blame History

layout title
documentation ES861C - ZWave

{% include base.html %}

ES861C Temperature Sensor

This describes the Z-Wave device ES861C, manufactured by LS Control with the thing type UID of lscontrol_es861c_00_000.

The device is in the category of Sensor, defining Device used to measure something.

ES861C product image

The ES861C does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.

Overview

Temperature Sensor

Inclusion Information

Internal Button

Exclusion Information

Internal Button

Wakeup Information

The ES861C does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.

The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Not Provided

General Usage Information

The sync button is inside the case, and to open the case you need to pop off the little plastic bump on the top to gain access to the screw which holds the thing together

Channels

The following table summarises the channels available for the ES861C -:

Channel Name Channel ID Channel Type Category Item Type
Sensor (temperature) sensor_temperature sensor_temperature Temperature Number:Temperature
Battery Level battery-level system.battery_level Battery Number

Sensor (temperature)

Indicates the current temperature.

The sensor_temperature channel is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.

Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category. This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.

Device Configuration

The following table provides a summary of the 3 configuration parameters available in the ES861C. Detailed information on each parameter can be found in the sections below.

Param Name Description
1 Delta Percentage 2 % - 56 % -> Delta
2 Celsius/Fahrenheit 0 - 64 -> Celsius : 64 - 127 -> Fahrenheit
3 Send Setpoint when WakeUp 0 - 64 -> SEND : 64 - 127 -> DO NOT SEND
Wakeup Interval Sets the interval at which the device will accept commands from the controller
Wakeup Node Sets the node ID of the device to receive the wakeup notifications

Parameter 1: Delta Percentage

2 % - 56 % -> Delta

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Celsius/Fahrenheit

0 - 64 -> Celsius : 64 - 127 -> Fahrenheit

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Send Setpoint when WakeUp

0 - 64 -> SEND : 64 - 127 -> DO NOT SEND

Values in the range 0 to 255 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.

This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID wakeup_interval and is of type INTEGER.

Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID wakeup_node and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ES861C supports 1 association group.

Group 1: Status Reports

Association group 1 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_BASIC_V1 Linked to BASIC
COMMAND_CLASS_SENSOR_MULTILEVEL_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_BATTERY_V1
COMMAND_CLASS_WAKE_UP_V1
COMMAND_CLASS_ASSOCIATION_V1
COMMAND_CLASS_VERSION_V1

Documentation Links

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.