OpenHAB
/
openhab-docs
mirror of https://github.com/openhab/openhab-docs.git
1
0
Fork 0
Code Issues Projects Releases Wiki Activity
openhab-docs/_addons_bindings/zwave/doc/leviton/zw15rz_0_0.md

5.1 KiB
Raw Permalink Blame History

layout title
documentation ZW15R - ZWave

{% include base.html %}

ZW15R Tamper-Resistant Z-Wave Outlet - Model ZW15R

This describes the Z-Wave device ZW15R, manufactured by Leviton with the thing type UID of leviton_zw15rz_00_000.

The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.

ZW15R product image

The ZW15R supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

The Decora Smart branded Z-Wave enabled outlet is designed for use with modern Z-Wave hubs.

This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. Your outlet will act as a repeater in the network to increase the reliability of the network.

Inclusion Information

  1. To enter programming mode, hold the button for 7seconds.  The status light will turn amber. Release and the status light will blink.
  2. Follow the Z-Wave controller instructions to enter inclusion mode.
  3. Tap the button one time.  The status light will quickly flash green.
  4. The Z-Wave controller will confirm successful inclusion to the network.

Exclusion Information

  1. To enter programming mode, hold the button for 7seconds.  The status light will turn amber. Release and the status light will blink.
  2. Follow Z-Wave controller directions to enter exclusion mode.
  3. Tap the the top of the paddle 1 time. The status light will quickly flash green.
  4. The Z-Wave controller will remove the device from the network.

When removing a device from a network it is best practice to use the exclusion process. In situations where a device needs to be returned to factory default follow the following steps. A reset should only be used when a controller is inoperable or missing.

  1. After holding the button for 7 seconds, the status light will turn amber. Continue holding the button for another 7 seconds (total of 14 seconds). Light will quickly flash red/amber.
  2. Release the button and the device will reset.

General Usage Information

Channels

The following table summarises the channels available for the ZW15R -:

Channel Name Channel ID Channel Type Category Item Type
Switch switch_binary switch_binary Switch Switch

Switch

Switch the power on and off.

The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.

Device Configuration

The following table provides a summary of the 1 configuration parameters available in the ZW15R. Detailed information on each parameter can be found in the sections below.

Param Name Description
7 Status LED Configuration Allow turning the status LED to various modes (off, status, locator)

Parameter 7: Status LED Configuration

Allow turning the status LED to various modes (off, status, locator) 0 = LED Off

254 = Status Mode

255 = Locater Mode Values in the range 0 to 255 may be set.

The manufacturer defined default value is 255.

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZW15R supports 1 association group.

Group 1: Controller

Lifeline Command Class: 0x5A01, 0x2503 and Ox8703

Association group 1 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SCENE_ACTIVATION_V1
COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1
COMMAND_CLASS_TRANSPORT_SERVICE_V1
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_SUPERVISION_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_INDICATOR_V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_SECURITY_V1
COMMAND_CLASS_SECURITY_2_V1

Documentation Links

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.