4.7 KiB

Raw Permalink Blame History

layout	title
documentation	DSC25 - ZWave

{% include base.html %}

DSC25 Smart Energy Illuminator G2

This describes the Z-Wave device DSC25, manufactured by AEON Labs with the thing type UID of aeon_dsc25_00_000.

The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.

The DSC25 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.

Overview

Plugin dimmer for a lamp

Inclusion Information

Press the Action Button
If successfully linked, the LED will no longer blink

Exclusion Information

Press the Action Button
If successfully removed, the LED will blink

Wakeup Information

The DSC25 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.

The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Channels

The following table summarises the channels available for the DSC25 -:

Channel Name	Channel ID	Channel Type	Category	Item Type
Dimmer	switch_dimmer	switch_dimmer	DimmableLight	Dimmer

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The following table provides a summary of the 1 configuration parameters available in the DSC25. Detailed information on each parameter can be found in the sections below.

Param	Name	Description
2	Configure Blinking LED
	Switch All Mode	Set the mode for the switch when receiving SWITCH ALL commands

Parameter 2: Configure Blinking LED

Values in the range 1 to 33000 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_2_2 and is of type INTEGER.

Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -:

Value	Description
0	Exclude from All On and All Off groups
1	Include in All On group
2	Include in All Off group
255	Include in All On and All Off groups

This parameter has the configuration ID switchall_mode and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The DSC25 supports 2 association groups.

Group 1: Hail Command / Basic Report

Association group 1 supports 5 nodes.

Group 2: Commands

Association group 2 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V1	Linked to BASIC
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_SCENE_ACTIVATION_V1
COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1
COMMAND_CLASS_METER_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_HAIL_V1
COMMAND_CLASS_ASSOCIATION_V1
COMMAND_CLASS_VERSION_V1

Documentation Links

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.

4.7 KiB Raw Permalink Blame History