9.4 KiB
| layout | title |
|---|---|
| documentation | DSC12 - ZWave |
{% include base.html %}
DSC12 Micro Smart Energy Switch
This describes the Z-Wave device DSC12, manufactured by AEON Labs with the thing type UID of aeon_dsc12_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The DSC12 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
The Aeon Labs Micro SES is a binary power switch device based on Zwave enhanced slave library V5.02P3.
Inclusion Information
Click the button once.
Exclusion Information
Click the button once.
Channels
The following table summarises the channels available for the DSC12 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Sensor (power) | sensor_power | sensor_power | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
Switch
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Sensor (power)
Indicates the energy consumption (kWh).
The sensor_power channel is of type sensor_power and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Electric meter (kWh)
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Electric meter (watts)
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Device Configuration
The following table provides a summary of the 13 configuration parameters available in the DSC12. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 2 | Make Micro Smart Switch Blink | |
| 3 | Current Overload Protection | |
| 80 | Notification on Status Change | |
| 90 | Enable Automated sending of a Report | Automated sending of a Report triggered by minimal change of value. |
| 91 | Minimum Change to send Report (Watt) | |
| 92 | Minimum Change to send Report (%) | |
| 101 | Automatic reports for group 1 | Which reports need to send automatically in timing intervals for group 1 |
| 102 | Automatic reports for group 2 | Which reports need to send automatically in timing intervals for group 2 |
| 103 | Automatic reports for group 3 | Which reports need to send automatically in timing intervals for group 3 |
| 111 | Interval to send out reports of group 1 | |
| 112 | Interval to send out reports of group 2 | |
| 113 | Interval to send out reports of group 3 | |
| 120 | Turn External Button Mode | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Parameter 2: Make Micro Smart Switch Blink
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_2_2 and is of type INTEGER.
Parameter 3: Current Overload Protection
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Deactivate |
| 1 | Activate |
The manufacturer defined default value is 0 (Deactivate).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Parameter 80: Notification on Status Change
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Deactivate |
| 1 | Hail CC Sent |
| 2 | Basic CC Report Sent |
The manufacturer defined default value is 0 (Deactivate).
This parameter has the configuration ID config_80_1 and is of type INTEGER.
Parameter 90: Enable Automated sending of a Report
Automated sending of a Report triggered by minimal change of value. Automated sending of a Report triggered by minimal change of value. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Deactivate |
| 1 | Activate |
The manufacturer defined default value is 0 (Deactivate).
This parameter has the configuration ID config_90_1 and is of type INTEGER.
Parameter 91: Minimum Change to send Report (Watt)
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 25.
This parameter has the configuration ID config_91_2 and is of type INTEGER.
Parameter 92: Minimum Change to send Report (%)
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_92_1 and is of type INTEGER.
Parameter 101: Automatic reports for group 1
Which reports need to send automatically in timing intervals for group 1 Which reports need to send automatically in timing intervals for group 1 Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 4.
This parameter has the configuration ID config_101_4 and is of type INTEGER.
Parameter 102: Automatic reports for group 2
Which reports need to send automatically in timing intervals for group 2 Which reports need to send automatically in timing intervals for group 2 Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 8.
This parameter has the configuration ID config_102_4 and is of type INTEGER.
Parameter 103: Automatic reports for group 3
Which reports need to send automatically in timing intervals for group 3 Which reports need to send automatically in timing intervals for group 3 Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_103_4 and is of type INTEGER.
Parameter 111: Interval to send out reports of group 1
Values in the range 1 to 2678400 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_111_4 and is of type INTEGER.
Parameter 112: Interval to send out reports of group 2
Values in the range 1 to 2678400 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_112_4 and is of type INTEGER.
Parameter 113: Interval to send out reports of group 3
Values in the range 1 to 2678400 may be set.
The manufacturer defined default value is 600.
This parameter has the configuration ID config_113_4 and is of type INTEGER.
Parameter 120: Turn External Button Mode
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Momentary Button Mode |
| 1 | 2 State Switch Mode |
| 2 | 3 Way Switch Mode |
The manufacturer defined default value is 255.
This parameter has the configuration ID config_120_1 and is of type INTEGER.
Switch All Mode
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The DSC12 supports 2 association groups.
Group 1: Target for automatic meter reports
Association group 1 supports 5 nodes.
Group 2: Target for automatic reports
Association group 2 supports 5 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V3 | |
| COMMAND_CLASS_METER_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.