9.3 KiB
| layout | title |
|---|---|
| documentation | ZW3010 - ZWave |
{% include base.html %}
ZW3010 In-Wall Smart Dimmer ZW3010 / 39351
This describes the Z-Wave device ZW3010, manufactured by Honeywell with the thing type UID of honeywell_zw3010_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The ZW3010 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
- WIRELESSLY CONTROL & SCHEDULE LIGHTS AND OTHER DEVICES– Wirelessly control switch from anywhere through your smartphone, tablet, PC or Z-Wave remote. Schedule timed events for connected devices and customize scenes for day or night, home or away - Switch can also be operated manually
- REQUIRES A Z-WAVE CERTIFIED HUB - Compatible with the following Z-Wave Hubs: Honeywell, Ring, SmartThings, Wink, HomeSeer, Fibaro, Trane, Nexia, ADT, Vera, and more.
- ALEXA COMPATIBLE (HUB REQUIRED) - Requires an Alexa supported hub for voice control with Amazon Echo Products (Alexa device and hub are sold separately). CANNOT connect directly with ECHO PLUS or other Alexa products (Only ZigBee products can connect directly to Echo Plus).
- IN-WALL INSTALLATION WITH HARD WIRED CONNECTIONS (NEUTRAL WIRE REQUIRED) – Replace your existing switch in as little as 15 minutes. Works with all LED, CFL, halogen and incandescent bulbs, and other devices.
- INCLUDES CHANGEABLE PADDLE COLORS – Includes white and light almond paddles to match any home décor. Features a blue LED indicator light to locate the switch in a dark room. Wall plate is NOT included.
Inclusion Information
Once the controller is ready to add your device, press and release the top or bottom of the smart fan control switch (rocker) to add it in the network.
Exclusion Information
NOTE: See Parameter 19 to set alternate exclusion mode
Once the controller is ready to add your device, press and release the top or bottom of the smart fan control switch (rocker) to add it in the network.
General Usage Information
Factory Reset
Quickly press ON (top) button three times, then immediately press the OFF (Bottom) button three times. The LED will flash ON/OFF five times when completed successfully.
Note: This should only be used if your network’s primary controller is missing or otherwise inoperable.
Channels
The following table summarises the channels available for the ZW3010 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | scene_number | Number |
Dimmer
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Scene Number
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
This channel provides the scene, and the event as a decimal value in the form <scene>.<event>. The scene number is set by the device, and the event is as follows -:
| Event ID | Event Description |
|---|---|
| 0 | Single key press |
| 1 | Key released |
| 2 | Key held down |
| 3 | Double keypress |
| 4 | Tripple keypress |
| 5 | 4 x keypress |
| 6 | 5 x keypress |
Device Configuration
The following table provides a summary of the 7 configuration parameters available in the ZW3010. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | LED Status | LED Status |
| 6 | Dim up/down rate | Dim up/down rate |
| 16 | Switch Mode | Switch Mode |
| 19 | Alternate Exclusion | Alternate Exclusion |
| 30 | Minimum Dim Threshold | Minimum Dim Threshold |
| 31 | Maximum Brightness Threshold | Maximum Brightness Threshold |
| 32 | Default Brightness Level | Default Brightness Level |
Parameter 3: LED Status
LED Status
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Device is ON, LED is OFF; device is OFF, LED is ON |
| 1 | Device is ON, LED is ON; device is OFF, LED is OFF |
| 2 | LED always OFF |
| 3 | LED always ON |
The manufacturer defined default value is 0 (Device is ON, LED is OFF; device is OFF, LED is ON).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Parameter 6: Dim up/down rate
Dim up/down rate Adjust the speed at which the ramps to a specific value other than 0 and FF The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Quickly |
| 1 | Slowly |
The manufacturer defined default value is 0 (Quickly).
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Parameter 16: Switch Mode
Switch Mode Turn your dimmer into an On/Off switch with switch mode The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Dimmer Mode |
| 1 | Switch Mode |
The manufacturer defined default value is 0 (Dimmer Mode).
This parameter has the configuration ID config_16_1 and is of type INTEGER.
Parameter 19: Alternate Exclusion
Alternate Exclusion Never accidentally remove a device with alternate exclusion.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Normal, Press Any Button on the device |
| 1 | Alternate |
The manufacturer defined default value is 0 (Normal, Press Any Button on the device).
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Parameter 30: Minimum Dim Threshold
Minimum Dim Threshold Set the minimum dimmer threshold when manually or remotely controlled Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_30_1 and is of type INTEGER.
Parameter 31: Maximum Brightness Threshold
Maximum Brightness Threshold Set the maximum brightness threshold when manually or remotely controlled Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_31_1 and is of type INTEGER.
Parameter 32: Default Brightness Level
Default Brightness Level Set the default brightness level that the dimmer will turn on when being controlled manually
- 0 = Default
- 1 - 99 = percentage Values in the range 0 to 99 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_32_1 and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZW3010 supports 3 association groups.
Group 1: Lifeline
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Z-Wave Plus Lifeline, Multilevel Switch Report
Association group 1 supports 5 nodes.
Group 2: Basic Set Local Load
Support Basic Set and is controlled with the local load Supports Basic Set and is controlled with local load
Association group 2 supports 5 nodes.
Group 3: Basic Set Double Press
Supports Basic Set and is controlled by double pressing the On or Off button Basic Set and is controlled by double pressing the ON or OFF button
Association group 3 supports 5 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_APPLICATION_STATUS_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_CENTRAL_SCENE_V3 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.