12 KiB
| layout | title |
|---|---|
| documentation | FT121 - ZWave |
{% include base.html %}
FT121 LED RGBWW Strip
This describes the Z-Wave device FT121, manufactured by Fantem with the thing type UID of oomi_ft121_00_000.
The device is in the category of Light Bulb, defining Devices that illuminate something, such as bulbs, etc..
The FT121 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
The LED Strip is a multi-colored LED Strip which allows control of color temperature (warm/cold white), RGB, and dimming via Z-Wave commands.
Inclusion Information
Set your Z-Wave controller into pairing mode. Press the Action Button located on the back of the LED Strip's white controller box once (The network LED will blink green as an indication it is pairing insecurely, please refer to section "Enabling Security Encryption" in the Advanced Function section of the manual to pair it securely). If the LED Strip has been successfully added to your Z-Wave network, its Network LED will become solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the instructions above from step 1.
Exclusion Information
Set your Z-Wave controller into device removal mode. Press the Action Button located on the back of the LED Strip's white controller box once. If the LED Strip has been successfully removed from your Z-Wave network, its Network LED will remain colorful gradient. If the removal was unsuccessful, the Network LED will still be solid, repeat the instructions above from step 1.
Channels
The following table summarises the channels available for the FT121 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Color Control | color_color | color_color | ColorLight | Color |
| Color Temperature | color_temperature | color_temperature | ColorLight | Dimmer |
Dimmer
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Color Control
The color channel allows to control the color of a light. It is also possible to dim values and switch the light on and off.
The color_color channel is of type color_color and supports the Color item and is in the ColorLight category.
Color Temperature
The color temperature channel allows to set the color temperature of a light from 0 (cold) to 100 (warm).
The color_temperature channel is of type color_temperature and supports the Dimmer item and is in the ColorLight category.
Device Configuration
The following table provides a summary of the 16 configuration parameters available in the FT121. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 20 | LED Strip state at Power ON | LED Strip state at Power ON |
| 32 | Enable/Disable Report on color change. | Enable/Disable Report on color change. |
| 34 | Brightness Level Control | Brightness Level Control |
| 35 | Display mode of Cold/warm white | Display mode of Cold/warm white |
| 37 | Colour Change Speed Level | Colour Change Speed Level |
| 37 | Time Base of Colour Change Speed | Time Base of Colour Change Speed |
| 37 | Cycle Count | Cycle Count |
| 37 | Brightness | Brightness |
| 37 | Colour Display Cycle | Colour Display Cycle |
| 37 | Colour Change Speed Option | Colour Change Speed Option |
| 37 | Colour Transition Style | Colour Transition Style |
| 40 | Colorful mode configuration | Colorful mode configuration |
| 80 | Notification (Group 1) when state changes | Notification (Group 1) when state changes |
| 112 | Dimmer mode | Dimmer mode |
| 252 | Configuration lock | Configuration lock |
| 255 | Reset to defaults | Reset to defaults |
Parameter 20: LED Strip state at Power ON
LED Strip state at Power ON
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Last State (default) |
| 0 | Remove Me |
| 1 | Always On |
| 2 | Always Off |
The manufacturer defined default value is 0 (Remove Me).
This parameter has the configuration ID config_20_1 and is of type INTEGER.
Parameter 32: Enable/Disable Report on color change.
Enable/Disable Report on color change.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable (default) |
| 1 | Hail CC |
The manufacturer defined default value is 0 (Disable (default)).
This parameter has the configuration ID config_32_1 and is of type INTEGER.
Parameter 34: Brightness Level Control
Brightness Level Control Enable/disable to turn on the last brightness level of the LED Strip when using the Color Switch Set CC to change its color. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable (default) |
| 1 | Enable |
The manufacturer defined default value is 0 (Disable (default)).
This parameter has the configuration ID config_34_1 and is of type INTEGER.
Parameter 35: Display mode of Cold/warm white
Display mode of Cold/warm white
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Arbitrary combination (default) |
| 1 | Complementary combination |
The manufacturer defined default value is 0 (Arbitrary combination (default)).
This parameter has the configuration ID config_35_1 and is of type INTEGER.
Parameter 37: Colour Change Speed Level
Colour Change Speed Level
- 0 = Constant speed
- 1 - 30 = Accelerate/decelerate speed from level 1 to 30
- 31 = Inactive (keep the current configuration values) Values in the range 0 to 31 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_37_4_0000001F and is of type INTEGER.
Parameter 37: Time Base of Colour Change Speed
Time Base of Colour Change Speed Time Base of Colour Change Speed The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Time base is 1s. |
| 1 | Time base is 10ms. |
| 2 | Time base is 100ms. |
The manufacturer defined default value is 0 (Time base is 1s.).
This parameter has the configuration ID config_37_4_000000E0 and is of type INTEGER.
Parameter 37: Cycle Count
Cycle Count
- 0 = Unlimited
- 1 - 254 = Total number of cycles before stopping
- 255 = Inactive (keep the current configuration values) Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_37_4_0000FF00 and is of type INTEGER.
Parameter 37: Brightness
Brightness
- 1 = Min level.
- 99 = Max level Values in the range 1 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_37_4_00FF0000 and is of type INTEGER.
Parameter 37: Colour Display Cycle
Colour Display Cycle
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Inactive |
| 1 | Rainbow Mode |
| 2 | Multi Colour Mode |
| 3 | Random Mode |
| 4 | Single Colour Mode. |
The manufacturer defined default value is 0 (Inactive).
This parameter has the configuration ID config_37_4_07000000 and is of type INTEGER.
Parameter 37: Colour Change Speed Option
Colour Change Speed Option Colour Change Speed Option Values in the range 0 to 15 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_37_4_38000000 and is of type INTEGER.
Parameter 37: Colour Transition Style
Colour Transition Style
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Smooth Colour Transition |
| 1 | Fade Out Fade In Transition |
The manufacturer defined default value is 0 (Smooth Colour Transition).
This parameter has the configuration ID config_37_4_40000000 and is of type INTEGER.
Parameter 40: Colorful mode configuration
Colorful mode configuration Set-only parameter The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Default |
| 1 | Rainbow mode |
| 2 | Multi color mode |
| 3 | Fade out and fade in (Red) |
| 4 | Fade out and fade in (Green) |
| 5 | Fade out and fade in (Blue) |
The manufacturer defined default value is 0 (Default).
This parameter has the configuration ID config_40_1_wo and is of type INTEGER.
This is a write only parameter.
Parameter 80: Notification (Group 1) when state changes
Notification (Group 1) when state changes
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Nothing |
| 1 | Hail CC (default) |
| 2 | Basic CC report |
The manufacturer defined default value is 1 (Hail CC (default)).
This parameter has the configuration ID config_80_1 and is of type INTEGER.
Parameter 112: Dimmer mode
Dimmer mode
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Parabolic curve |
| 1 | Index curve |
| 2 | (Parabolic * Index)/2 |
| 3 | Linear |
The manufacturer defined default value is 2 ((Parabolic * Index)/2).
This parameter has the configuration ID config_112_1 and is of type INTEGER.
Parameter 252: Configuration lock
Configuration lock This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Configuration allowed (default) |
| 1 | Configuration locked |
The manufacturer defined default value is 0 (Configuration allowed (default)).
This parameter has the configuration ID config_252_1 and is of type INTEGER.
Parameter 255: Reset to defaults
Reset to defaults This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 0 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_255_0 and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The device does not support associations.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_COLOR_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.