10 KiB
| layout | title |
|---|---|
| documentation | 50x5xx - ZWave |
{% include base.html %}
50x5xx Roller shutter push-button
This describes the Z-Wave device 50x5xx, manufactured by Merten with the thing type UID of merten_50x5xx_00_000.
The device is in the category of Blinds, defining Roller shutters, window blinds, etc..
The 50x5xx supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
The roller shutter push-button contains a radio receiver for the Merten CONNECT radio system. If you use the blind control inserts 580699 or 580698, you can operate the connected roller shutter drive remotely using a Merten CONNECT radio transmitter. You can also operate the roller shutters using the rocker on the roller shutter push-button.
You can use the Merten CONNECT radio button, the Merten CONNECT radio remote control or the Merten CONNECT radio central unit as the transmitter.
Inclusion Information
Program (transmits Node info frame)
Triple click on operating surface. Used for include/exclude the device by the primary
Exclusion Information
Reset to the factory settings; exclude
Triple click on operating surface. Used for include/exclude the device by the primary
Channels
The following table summarises the channels available for the 50x5xx -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Blinds Control | blinds_control | blinds_control | Blinds | Rollershutter |
| Sensor (luminance) | sensor_luminance | sensor_luminance | Number | |
| Dimmer 1 | switch_dimmer1 | switch_dimmer | DimmableLight | Dimmer |
| Sensor (luminance) 1 | sensor_luminance1 | sensor_luminance | Number | |
| Dimmer 2 | switch_dimmer2 | switch_dimmer | DimmableLight | Dimmer |
Blinds Control
Provides start / stop control of blinds.
The blinds_control channel is of type blinds_control and supports the Rollershutter item and is in the Blinds category.
Sensor (luminance)
Indicates the current light reading.
The sensor_luminance channel is of type sensor_luminance and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Dimmer 1
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer1 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Sensor (luminance) 1
Indicates the current light reading.
The sensor_luminance1 channel is of type sensor_luminance and supports the Number item. This is a read only channel so will only be updated following state changes from the device.
Dimmer 2
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer2 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Device Configuration
The following table provides a summary of the 11 configuration parameters available in the 50x5xx. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 176 | Changeover delay (motor protection) | Changeover delay (motor protection) |
| 177 | Raising time (Input 1) | Raising time (Input 1) |
| 178 | Raising time (Input 2) | Raising time (Input 2) |
| 179 | Lowering time (input 1) | Lowering time (Input 1) |
| 180 | Lowering time (Input 2) | Lowering time (Input 2) |
| 181 | Inclusion of light sensor | Inclusion of light sensor |
| 182 | Brightness threshold | Brightness threshold |
| 183 | Reaction threshold for raising shutter (Input 1) | Reaction threshold for raising shutter (Inpuit 1) |
| 184 | Reaction threshold for raising shutter (Input 2) | Reaction threshold for raising shutter (Input 2) |
| 185 | Reaction threshold for lowering shutter (Input 1) | Reaction threshold for lowering shutter (Input 1) |
| 186 | Reaction threshold for lowering shutter (Input 2) | Reaction threshold for lowering shutter (Input 2) |
Parameter 176: Changeover delay (motor protection)
Changeover delay (motor protection) Allowed values: 0-255
Changeover delay = Input * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_176_1 and is of type INTEGER.
Parameter 177: Raising time (Input 1)
Raising time (Input 1) Allowed values: 0-255
Raising time = (256 * Input 1 + Input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_177_1 and is of type INTEGER.
Parameter 178: Raising time (Input 2)
Raising time (Input 2) Allowed values: 0-255
Raising time = (256 * Input 1 + Input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_178_1_wo and is of type INTEGER.
This is a write only parameter.
Parameter 179: Lowering time (input 1)
Lowering time (Input 1) Allowed values: 0-255
Lowering time = (256 * Input 1 + Input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_179_1 and is of type INTEGER.
Parameter 180: Lowering time (Input 2)
Lowering time (Input 2) Allowed values: 0-255
Lowering time = (256 * Input 1 + Input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_180_1 and is of type INTEGER.
Parameter 181: Inclusion of light sensor
Inclusion of light sensor
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Auto |
| 1 | Enable |
| 2 | Disable |
The manufacturer defined default value is 0 (Auto).
This parameter has the configuration ID config_181_1 and is of type INTEGER.
Parameter 182: Brightness threshold
Brightness threshold Allowed values: 0-255 Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_182_1 and is of type INTEGER.
Parameter 183: Reaction threshold for raising shutter (Input 1)
Reaction threshold for raising shutter (Inpuit 1) Allowed values: 0-255
(256 * Input 1 + input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_183_1 and is of type INTEGER.
Parameter 184: Reaction threshold for raising shutter (Input 2)
Reaction threshold for raising shutter (Input 2) Allowed values: 0-255
(256 * Input 1 + input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_184_1 and is of type INTEGER.
Parameter 185: Reaction threshold for lowering shutter (Input 1)
Reaction threshold for lowering shutter (Input 1) Allowed values: 0-255
(256 * Input 1 + input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_185_1 and is of type INTEGER.
Parameter 186: Reaction threshold for lowering shutter (Input 2)
Reaction threshold for lowering shutter (Input 2) Allowed values: 0-255
(256 * Input 1 + input 2) * 0.1s Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_186_1 and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 50x5xx supports 1 association group.
Group 1: Other device to be switched
Association group 1 supports 5 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_BASIC_WINDOW_COVERING_V1 | Linked to BASIC |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_PROTECTION_V2 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_SENSOR_CONFIGURATION_V1 |
Endpoint 1
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1 | |
| COMMAND_CLASS_BASIC_WINDOW_COVERING_V1 | Linked to BASIC |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_PROTECTION_V2 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_SENSOR_CONFIGURATION_V1 |
Endpoint 2
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_BASIC_WINDOW_COVERING_V1 | Linked to BASIC |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_PROTECTION_V2 | |
| COMMAND_CLASS_VERSION_V1 |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.