4.5 KiB
| layout | title |
|---|---|
| documentation | ACC01 - ZWave |
{% include base.html %}
ACC01 HKZW
This describes the Z-Wave device ACC01, manufactured by Hank with the thing type UID of hank_acc01_00_000.
The device is in the category of Remote Control, defining Any portable or hand-held device that controls the status of something, e.g. remote control, keyfob etc..
The ACC01 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Overview
ACC01 is an IR Transceiver based on Z-Wave technology. It is used for sending IR codes to infrared communicaiton controlling devices suchas TV, air condition, and TV box.
Inclusion Information
Triple click the Z-Button within 1.5 seconds.
For secure inclusion, press and hold the button for 3 seconds.
Exclusion Information
Triple click the Z-Button within 1.5 seconds.
Channels
The following table summarises the channels available for the ACC01 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|
Device Configuration
The following table provides a summary of the 3 configuration parameters available in the ACC01. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 93 | Clear IR information | Clear IR information |
| 254 | Enable/Disable configuration | |
| 255 | Reset & remove from Z-Wave network | Reset & remove from Z-Wave network |
Parameter 93: Clear IR information
Clear IR information
The following option values may be configured, in addition to values in the range 1 to 1431655765 -:
| Value | Description |
|---|---|
| 1431655765 | Clear IR Information |
The manufacturer defined default value is 1.
This parameter has the configuration ID config_93_4 and is of type INTEGER.
Parameter 254: Enable/Disable configuration
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Unlock |
| 1 | Lock |
The manufacturer defined default value is 0 (Unlock).
This parameter has the configuration ID config_254_1 and is of type INTEGER.
Parameter 255: Reset & remove from Z-Wave network
Reset & remove from Z-Wave network This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. The following option values may be configured, in addition to values in the range 1 to 1431655765 -:
| Value | Description |
|---|---|
| 1431655765 | Reset & remove from network |
The manufacturer defined default value is 1.
This parameter has the configuration ID config_255_4 and is of type INTEGER.
Association Groups
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ACC01 supports 1 association group.
Group 1: Lifeline
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Technical Information
Endpoints
Endpoint 0
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SIMPLE_AV_CONTROL_V1 | Linked to BASIC |
Documentation Links
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.