OpenHAB
/
openhab-docs
mirror of https://github.com/openhab/openhab-docs.git
1
0
Fork 0
Code Issues Projects Releases Wiki Activity
openhab-docs/_addons_bindings/zwave/doc/nietech/evalogikzw39_0_0.md

4.8 KiB
Raw Permalink Blame History

layout title
documentation ZW39 - ZWave

{% include base.html %}

ZW39 Dimmable Smart Plug

This describes the Z-Wave device ZW39, manufactured by NIE Technology with the thing type UID of nietech_evalogikzw39_00_000.

The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.

ZW39 product image

The ZW39 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

EVA LOGIK ZW39 Plug is a Z-Wave PLUS On/Off + Dimmer Smart Plug-In Module + Z-Wave Range Extender which has one dimming smart plug.

  • Maximum load for the Z-Wave controlled outlet: 2.5A; 300W Incandescent or 100W Dimmable CFL/LED
  • One Z-Wave controlled AC outlet for standard incandescent lighting or dimmable CFL/LEDs
  • Remote ON/OFF and brightness control via the Z-Wave controller
  • Manual ON/OFF and brightness control with the front panel push button
  • Load-sensing turns the light ON if the switch on the connected light is used instead of the remote or push button on the Z-Wave smart switch (default setting is disabled)
  • Space efficient design
  • Does not block the lower outlet when plugged in to the upper outlet of a duplex wall receptacle. (This assumes that the duplex receptacle is mounted with the ground pin down).
  • Plugs and cords for connected devices route to the side allowing close placement

Inclusion Information

  1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.
  2. Once the controller is ready to include your device, quick triple press the button to include it in the network.
  3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.
  4. The device is associated in the same group when it included in setting process.

Now you can control your Z-Wave device according to groups, scenes, schedules and automation programmed. If your controller features remote access, you can now control all devices in Z-Wave network from mobile devices

Exclusion Information

  1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.
  2. Once the controller is ready to Exclude your device, quick triple press the button to exclude it from the network.

Channels

The following table summarises the channels available for the ZW39 -:

Channel Name Channel ID Channel Type Category Item Type
Dimmer switch_dimmer switch_dimmer DimmableLight Dimmer

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.

Device Configuration

The device has no configuration parameters defined.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZW39 supports 1 association group.

Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.

Association group 1 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_SWITCH_ALL_V1
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Documentation Links

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.