openhab-docs/_addons_bindings/zwave/doc/mobilus/m35ezrs_0_0.md

layout	title
documentation	EZRS - ZWave

{% include base.html %}

EZRS Mobilus Tubular Motor

This describes the Z-Wave device EZRS, manufactured by MOBILUS MOTOR Spólka z o.o. with the thing type UID of mobilus_m35ezrs_00_000.

The device is in the category of Blinds, defining Roller shutters, window blinds, etc..

The EZRS supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

Tubular motor mob.iq EZRS M35 10/14 by Mobilus Motor Company is a modern radio controllable drive, designed to drive rolling shields. This device has a number of innovative solutions, including:

SENSO technology

• programming of endpoints automatically or using the remote control, 
• operation regardless of the used hangers type, 
• bidirectional obstacles detection which eliminates failures due to obstacles (each failure will be reported to controller as an alarm)
• saving your time due to lack of supervision of your shutters - obstacle detection system, insensitive to minor disruption during work.

Communication standard

But the most important feature of our motor is the usage of Z-Wave technology as the communication standard. It provides inter alia

• easy procedure of connection the device to the network,
• bidirectional communication between the motor operator and control device - therefore the user has the opportunity to receive a variety of information about the motor operator (location, work errors, obstacles encountered in the blinds way of work), 
• automatic creation of network of devices, so there is no need for additional radio signal repeaters, 
• compatibility with third party control devices - Z-Wave is a mature standard for radio communication, chosen by over two hundred manufacturers of devices intended to create an intelligent home control systems.

Technical parameters

• fi roller tube diameter of 35 mm,
• torque: 10 Nm, 
• revolutions per minute: 14 rpm, 
• supply voltage 230 V.

Inclusion Information

1. Plug mob.iq [ M35 EZRS ] motor to the power supply according to schema at the end of instruction. Green diode in PROGRAMMING BUTTON is on. In the other case you need to exclude motor from Z-Wave network according to point 4 of this instruction.
2. Turn your controller into INCLUDE mode (see instruction of your controller).
3. Press the PROGRAMMING BUTTON on mob.iq [ M35 EZRS ] motor.
4. Motor is detected by controller and included into Z-Wave network - the led diode is off.

Exclusion Information

1. Turn your controller into exclude mode (see instruction of your controller).
2. Press the PROGRAMMING BUTTON on mob.iq [ M35 EZRS ] motor.
3. Motor is detected by controller and excluded from Z-Wave network - the led diode is on.

Channels

The following table summarises the channels available for the EZRS -:

Channel Name	Channel ID	Channel Type	Category	Item Type
Switch	switch_binary	switch_binary	Switch	Switch
Dimmer [Deprecated]	switch_dimmer	switch_dimmer	DimmableLight	Dimmer
Blinds Control	blinds_control	blinds_control	Blinds	Rollershutter
Alarm (system)	alarm_system	alarm_system		Switch

Switch

Switch the power on and off.

The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.

Dimmer [Deprecated]

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.

Note: This channel is marked as deprecated so should not be used.

Blinds Control

Provides start / stop control of blinds.

The blinds_control channel is of type blinds_control and supports the Rollershutter item and is in the Blinds category.

Alarm (system)

Indicates if a system alarm is triggered.

The alarm_system channel is of type alarm_system and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the Switch item type -:

Value	Label
OFF	OK
ON	Alarm

Device Configuration

The following table provides a summary of the 2 configuration parameters available in the EZRS. Detailed information on each parameter can be found in the sections below.

Param	Name	Description
12	Motor state mode	Allows to change motor state (normal/calibration/discalibration mode)
13	BASIC SET Respone	Allows to change motor behavior after receiving BASIC_SET with value 0xFF

Parameter 12: Motor state mode

Allows to change motor state (normal/calibration/discalibration mode)

The following option values may be configured -:

Value	Description
0	Normal mode (default)
1	Calibration mode
2	Discalibration mode

The manufacturer defined default value is 0 (Normal mode (default)).

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 13: BASIC SET Respone

Allows to change motor behavior after receiving BASIC_SET with value 0xFF

The following option values may be configured -:

Value	Description
0	last known non-zero position (default)
1	max open

The manufacturer defined default value is 0 (last known non-zero position (default)).

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The EZRS supports 3 association groups.

Group 1: I ASSOCIATION GROUP

Allows to send information about failures, errors and alarms directly to the controller (max. 5 devices).

Association group 1 supports 5 nodes.

Group 2: II ASSOCIATION GROUP

Allows to send direct steering commands between SLAVE devices without participation of PRIMARY controller (max. 5 devices).

Association group 2 supports 5 nodes.

Group 3: III ASSOCIATION GROUP

Allows to send direct steering commands (BASIC_SET with value 0xFF) to other devices if error is detected (max. 5 devices).

Association group 3 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class	Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_ALARM_V8
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_NODE_NAMING_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_SECURITY_V1

Documentation Links

• Manual

---

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.