According to the documentation, `NRF52840_DK` does not support odd parity and 2 stop bits. Skip these test case using #if !defined(TARGET_NRF52840) directive.
This is temporary solution. In the future we shell consider adding `uart_get_capabilities()` function.
-
Increase coverage of the SPI master FPGA test:
- check supported frequencies (based on the device capabilities),
- add support for manual CS handling and test cases,
- add test cases for rx/tx buffers with different length (based on the device capabilities),
- add test case for one symbol transmission,
- add test cases for different symbol sizes (based on the device capabilities).
Tests sequence swaped:
ASYNCHRONOUS_DNS_TIMEOUTS
ASYNCHRONOUS_DNS_INVALID_HOST
This is temporary solution to prevent Jenkins fail until root cause will be fixed.
Enabled heap_and_stack test for baremetal.
Added a test to check that global variables are initialised.
In mbed_sdk_boot:
- Added initialisation for mbed_stack_isr_start/size and mbed_heap_start/size for all toolchains.
- ARM toolchain:
- Added call to mbed_toolchain_init() to initialise global variables.
- Moved microlib initialisation code from mbed_retarget.cpp to mbed_sdk_boot.c.
- IAR toolchain: there is no equivalent to a software init hook that can be called. __low_level_init() was used but since this function is called before RAM initialisation, it cannot be used to initialize global variables. Defined a new __mbed_init() function called from IAR startup file instead.
On some targets with very fast counters used for us ticker (e.g. 26 MHz) tested interrupt delays provided in the ticker_timeout array may be too short (execution of the set_interrupt() function takes longer than the tested delay).
We will skip tested ticker delay if the delay is less than assumed max set_interrupt() function execution time (20 us).
Also, the test array will be extended.
Original default constructor implementation wasn't quite working
properly; it didn't cope with the new "mode_limit" parameter.
Change mechanism so that this now works:
MbedCRC<POLY32_BIT_ANSI_CRC, 32, CrcMode::TABLE> crc;
CRC tests failed to exercise handling of the initial and final-xor
values with respect to reflection parameters. Add tests covering this.
Expected behaviour is that the initial value is always non-reflected and
the final-xor happens after the optional output reflection.
Replace the thread used in the test case teardown with a Ticker to allow
testing with the bare metal profile. This Ticker is used to prevent the
watchdog from resetting the device during the final greentea
communication.
This is because the ESP8266 is now waiting for SEND OK and takes much
more to complete the send_repeat, and echo_burst tests in RAAS.
(but has higher pass ratio).
Update Mbed OS's PSA Crypto service to work with Mbed Crypto 3.x.
- psa_asymmetric_verify() is now called psa_verify_hash().
- psa_asymmetric_sign() is now called psa_sign_hash().
Compatibilty wrappers are provided via crypto_compat.h for source-level
backwards compatibility.
- By default, Mbed OS build tools use standard C library for all supported toolchains.
It is possible to use smaller C libraries by overriding the "target.default_lib" option
with "small". This option is only currently supported for the GCC_ARM toolchain.
This override config option is now extended in the build tool for ARM toolchain.
- Add configuration option to specify libraries supported for each toolchain per targets.
- Move __aeabi_assert function from rtos to retarget code so it’s available for bare metal.
- Use 2 memory region model for ARM toolchain scatter file for the following targets:
NUCLEO_F207ZG, STM32F411xE, STM32F429xI, NUCLEO_L073RZ, STM32F303xE
- Add a warning message in the build tools to deprecate uARM toolchain.
- NewLib-Nano C library is not supporting floating-point and printf with %hhd,%hhu,%hhX,%lld,%llu,%llX
format specifier so skipping those green tea test cases.
New members are added to the network interface
-getaddrinfo
-getaddrinfo_async
gethostbyname is unchanged but gethostbyname_async result param now contains results od DNS records found.
Test cases for sync/async added added to DNS test folder.
* Deprecate RawSerial.
* Introduce UnbufferedSerial to provide unbuffered I/O by implementing
with a FileHandle interface for I/O streams.
* Add Greentea test for the UnbufferedSerial class.
Added missing mbed_error_initialize function call in bare metal boot code which is used
to retrieve the crash report from RAM in case of any previous abnormal re-boot but this function call is present in RTOS boot code.
For consistency with `std::shared_ptr`, and `mbed::Callback`, and as a
potential optimisation aid, give `SharedPtr` a distinct constructor for
`nullptr`.
The fs integration tests requires about 10 little fs blocks.
The qspi erase size is 256K, with the default size of 2MB, this only
allocates 8 little fs blocks. The tests need 10 little fs blocks to
work.
Also Added no-led tags to cypress board that only have 1 LED. The
fs integration tests blinks 2 LEDs.
UDPSocket can be used also similar to TCPSocket using connect(), send() and recv() methods.
This commit adds UDP ECHOTESTS which uses these methods instead of sendto() and recvfrom().
* Use compile-time detection of hardware CRC capability, so unneeded
code and tables do not go into the image.
* Add global JSON config option to allow choice between no tables,
16-entry tables or 256-entry tables for software CRC. Default set
to 16-entry, reducing ROM size from previous 256-entry.
* Allow manual override in template parameter to force software or
bitwise CRC for a particular instance.
* Micro-optimisations, particularly use of `RBIT` instruction and
optimising bitwise computation using inline assembler.
Incompatible changes:
* Remove special-case "POLY_32BIT_REV_ANSI" - users can use standard
POLY_32BIT_ANSI, which now uses the same 16-entry tables by default,
or can use hardware acceleration, which was disabled for
POLY_32BIT_REV_ANSI. MbedCRC<POLY_32BIT_ANSI, 32, CrcMode::TABLE> can
be used to force software like POLY_32BIT_REV_ANSI.
* The precomputed table for POLY_16BIT_IBM had errors - this has been
corrected, but software CRC results will be different from the previous
software calculation.
* < 8-bit CRC results are no longer are shifted up in the output value,
but placed in the lowest bits, like other sizes. This means that code
performing the SD command CRC will now need to use `(crc << 1) | 1`,
rather than `crc | 1`.
* Change "is supported" check to be a macro, so it can be done at
compile-time.
* Eliminate weird shift on 7-bit CRCs.
* Add support for 32-bit CRCs and reversals to TMPM3HQ.
This test is failed since #11721 Bare metal greentea support
on many STM32 boards:
NUCLEO_F072RB, NUCLEO_F070RB
NUCLEO_F411RE, NUCLEO_F439ZI, NUCLEO_F446ZE, DISCO_F407VG
NUCLEO_F303RE
...
In this test case if asynchronous DNS request results does not happen
in requested time, the request must be cancelled to ensure it does not
happen later on when test has exited already.
We've seen couple of crashes in CI tests which indicate this kind of behaviour
but this is very difficult to reproduce.
MBED_DEPRECATE macros is added to string-based APIs.
New, non-string-based APIs are added in their place.
Wiced binaries rebuilt
Any existing stubs or mocks are adjusted to compile and run with the newly added non-string based functions.
* Use compile-time detection of hardware CRC capability, so unneeded
code and tables do not go into the image.
* Add global JSON config option to allow choice between no tables,
16-entry tables or 256-entry tables for software CRC. Default set
to 16-entry, reducing ROM size from previous 256-entry.
* Allow manual override in template parameter to force software or
bitwise CRC for a particular instance.
* Micro-optimisations, particularly use of `RBIT` instruction and
optimising bitwise computation using inline assembler.
Incompatible changes:
* Remove special-case "POLY_32BIT_REV_ANSI" - users can use standard
POLY_32BIT_ANSI, which now uses the same 16-entry tables by default,
or can use hardware acceleration, which was disabled for
POLY_32BIT_REV_ANSI. MbedCRC<POLY_32BIT_ANSI, 32, CrcMode::TABLE> can
be used to force software like POLY_32BIT_REV_ANSI.
* The precomputed table for POLY_16BIT_IBM had errors - this has been
corrected, but software CRC results will be different from the previous
software calculation.
* < 8-bit CRC results are no longer are shifted up in the output value,
but placed in the lowest bits, like other sizes. This means that code
performing the SD command CRC will now need to use `(crc << 1) | 1`,
rather than `crc | 1`.
* Change "is supported" check to be a macro, so it can be done at
compile-time.
* Eliminate weird shift on 7-bit CRCs.
* Add support for 32-bit CRCs and reversals to TMPM3HQ.
Chun-Chieh Li
Przemyslaw Stekiel
Qinghao Shi
Martin Kojtal
Kevin Bracey
Tymoteusz Bloch
Ari Parkkila
jeromecoutant
Michal Paszta
Anna Bridge
Evelyne Donnaes
Rajkumar Kanagaraj
Filip Jagodzinski
Hugues Kamba
cyliangtw
Jaeden Amero
Kimmo Vaisanen
YARB(Cypress)
Chris Trowbridge
Shuopeng Deng
Marcin Tomczyk
Veijo Pesonen
Alexandre Bourdiol
MarceloSalazar
Kyle Kearney