In IRQ Handler, to disable some interrupt type of DMA error.
It could avoid unexpected repeated interrupt.The masked bit of
DMA_IE could be recovered in next EMAC IRQ event.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
When IPv6 is prefered it will choose a link local address on a network
that lacks IPv6 over a working IPv4 network, breaking networking.
Change this behaviour to prefer a link local address only as a last
resort.
This also changes LWIP::get_ipv6_addr to not return link local
addresses. Use get_ipv6_link_local_addr instead for this.
Add null check for return values of functions that are mostly (but not
always) checked for null.
E.g., since 98% of calls to protocol_stack_interface_info_get_by_id
check for null, it is likely that the function can return null values in
some cases, and omitting the check could crash the program.
Storing the address of a local variable (`secret_buf`)
in non-local memory (`prf_ptr->secret`) can cause a
dangling pointer bug if the address is used after the function returns.
The member function bringup() of class ThreadInterface redefines
parameter stack's default value to IPV6_STACK from the inherited default value
DEFAULT_STACK (in Interface).
The default value will be resolved statically, not by dispatch, so this
can cause confusion.
Similar arguments apply to LoWPANNDInterface and WisunInterface.
Virtual functions are resolved statically (not dynamically) in
constructors and destructors for the same class. The call should be made
explicitly static by qualifying it using the scope resolution operator.
If user sets the default interface ID for a socket (e.g. using setsockopt
with SOCKET_INTERFACE_SELECT), the default interface should take over
other interface selection mechanisms as a interface is bound to the socket.
This applies for both IPv6 local and global scopes for unicast messages
but not for multicast messages as these are bound to a multicast interface
using SOCKET_IPV6_MULTICAST_IF socket option.
- add board specific EMAC setup to connectivity/drivers/emac/TARGET_STM/TARGET_STM32H7
- stm32h7_eth_init.c was derived from the NUCLEO-H743ZI2 code whilst comparing to the output of STM32CubeIDE
- complete board specific code in targets/TARGET_STM/TARGET_STM32H7/TARGET_STM32H723xG
- PeripheralPins.c and PinNames.h were created by targets/TARGET_STM/tools/STM32_gen_PeripheralPins.py
- ST ZIO connector pins in PinNames.h have been adapted from NUCLEO-H743ZI2
- CONSOLE_TX and CONSOLE_RX have been interchanged in PinNames.h to match the actual board layout
- startup_stm32h723xx.S was derived from startup_stm32h743xx.S
- stm32h723xg.ld was completely rewritten to match the actual MCU including:
- split heap support
- SRAM2 and SRAM4 support
- crash dump support
- proper use of DTCM as stack
- system_clock.c has been changed to support the maximal main clock speed of 550 MHz
- fix handling of HS in FS mode for the target board in targets/TARGET_STM/USBPhy_STM32.cpp
- add board definition to targets/targets.json and correct linker setup for the chip
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
1. Crypto RSA H/W supports 1024/2048/3072/4096 key bits. Fall back to software implementation for other key bits.
2. For decrypt, if MBEDTLS_RSA_NO_CRT isn't defined, go CRT, or normal.
3. For decrypt, when blinding (f_rng != NULL), enable SCAP mode.
4. Recover from Crypto RSA H/W failure:
(1) Enable timed-out wait to escape from RSA H/W trap
(2) On RSA H/W timeout, stop this RSA H/W operation
(3) Fall back to S/W implementation on failure
NOTE: RSA 4096 key bits can fail with default mbedtls configuration MBEDTLS_MPI_MAX_SIZE.
Enlarge MBEDTLS_MPI_MAX_SIZE to 1024 or larger if this feature is required.
NOTE: Fixed in BSP RSA driver, for non-CRT+SCAP mode, temporary buffer for MADDR6 requires to be key length plus 128 bits.
NOTE: Fixed in BSP RSA driver, DMA buffer must be 4-word aligned, or RSA H/W will trap.
1. Prepare crypto common code
2. Support list
- SHA
- ECC
NOTE: AES/RSA are to support in other works
NOTE: Compared to M487, M467's SHA supports context save & restore (DMA Cascade mode) and so no software fallback is needed.
NOTE: M467's ECC, following M487, goes partial-module replacement and it can just improve primitives e.g. point addition/doubling by 2X,
and cannot improve high level point multiplication because MbedTLS doesn’t open it.
To improve performance best, full-module replacement is needed.
NOTE: Continuing above, add support for Montgomery curve
RFC3315 specifies the following: "The relay agent MAY send the Interface-id
option to identify the interface on which the client message was received.
If a relay agent receives a Relay-reply message with an Interface-id
option, the relay agent relays the message to the client through the
interface identified by the option."
The current implementation of the DHCP relay reply handling, the interface
ID field from the server response is ignored. Managing the interface ID
is very important especially as DHCP requests/replies use link-local
addresses. The consequence of this is that the interface must always be
specified because the routing layer cannot guess the correct interface.
Moreover, Mbed provides a mechanism to enable/disable the interface ID
option on a DHCP relay instance, so it is important to fully support it.
The reason why this issue has not been discoverd until now is that the DHCP
relay is mainly used on systems that use only one interface (such as Wi-SUN
routers). By default, when no interface ID is specified for the socket, the
latter will choose 6loWPAN interface by default. This means that if two
interfaces are used on the same device, the 6loWPAN interface is always
selected.
The commit adds code to retrieve the interface-id value contained within
the DHCP relay reply message and write it to a control message header
that is added to the socket message. This tells the socket which
interface to choose. If the interface-id option is not enabled on the
relay, this procedure is simply ignored.
Charles
Martin Kojtal
Lukas Karel
cyliang tw
Jost, Chris
Jookia
Mingjie Shen
Saheer Babu
akiroz
YannCharbon
Daniel Starke
Chun-Chieh Li
Jerome Coutant
Danny Goossen