These targets below just support PRNG, not real TRNG. They cannot annouce TRNG.
- NUMAKER_PFM_NUC472
- NUMAKER_PFM_M487
- NUMAKER_IOT_M487
On targets without TRNG, to run mbedtls applications which require entropy source,
there are two alternatives to TRNG:
- Custom entropy source:
Define MBEDTLS_ENTROPY_HARDWARE_ALT and provide custom mbedtls_hardware_poll(...)
- NV seed:
1. Define MBEDTLS_ENTROPY_NV_SEED
2. Define MBEDTLS_PLATFORM_NV_SEED_READ_MACRO/MBEDTLS_PLATFORM_NV_SEED_WRITE_MACRO and provide custom mbedtls_nv_seed_read(...)/mbedtls_nv_seed_write(...).
3. Don't define MBEDTLS_PSA_INJECT_ENTROPY. Meet mbedtls_psa_inject_entropy(...) undefined and then provide custom one, which must be compatible with mbedtls_nv_seed_read(...)/mbedtls_nv_seed_write(...) above.
4. For development, simulating partial provision process, inject entropy seed via mbedtls_psa_inject_entropy(...) pre-main.
Reasons to remove TRNG support:
1. M252 just has 32KiB SRAM and cannot afford mbedtls application.
2. Implementing TRNG HAL with PRNG H/W has security concern.
Without free-up of peripheral pins, peripheral pins of the same peripheral may
share by multiple ports after port iteration, and this peripheral may fail with
pin interference.
In Nuvoton, only new-design chips support GPIO input pull-high/pull-low modes.
Targets not supporting this feature are listed below:
- NUMAKER_PFM_NANO130
- NUMAKER_PFM_NUC472
- NUMAKER_PFM_M453
Fix logic error on replying NACK at the end of transfer.
This is also to fix FPGA CI test mbed_hal_fpga_ci_test_shield-i2c/
i2c - test single byte read i2c API.
Better IP initialization sequence:
1. Configure IP pins
2. Select IP clock source and then enable it
3. Reset the IP (SYS_ResetModule)
NOTE1: IP reset takes effect regardless of IP clock. So it doesn't matter if
IP clock enable is before IP reset.
NOTE2: Non-configured pins may disturb IP's state, so IP pinout first and then
IP reset.
NOTE3: IP reset at the end of IP initialization sequence can cover unexpected
situation.
Without free-up of peripheral pins, peripheral pins of the same peripheral may
share by multiple ports after port iteration, and this peripheral may fail with
pin interference.
In Nuvoton, only new-design chips support GPIO input pull-high/pull-low modes.
Targets not supporting this feature are listed below:
- NUMAKER_PFM_NANO130
- NUMAKER_PFM_NUC472
- NUMAKER_PFM_M453
Fix logic error on replying NACK at the end of transfer.
This is also to fix FPGA CI test mbed_hal_fpga_ci_test_shield-i2c/
i2c - test single byte read i2c API.
Better IP initialization sequence:
1. Configure IP pins
2. Select IP clock source and then enable it
3. Reset the IP (SYS_ResetModule)
NOTE1: IP reset takes effect regardless of IP clock. So it doesn't matter if
IP clock enable is before IP reset.
NOTE2: Non-configured pins may disturb IP's state, so IP pinout first and then
IP reset.
NOTE3: IP reset at the end of IP initialization sequence can cover unexpected
situation.
Fix SPI module index error in modidx_ns_tab table in CLK_SetModuleClock_S().
Need to update secure image for this bugfix.
This is also to fix FPGA CI test mbed_hal_fpga_ci_test_shield-spi/
SPI - init/free test all pins.
M451 series can classify by M45xD/M45xC and M45xG/M45xE. To support this
classification:
1. Create TARGET_M45xD_M45xC and TARGET_M45xG_M45xE targets.
2. Mark NUMAKER_PFM_M453 belongs to TARGET_M45xG_M45xE by 'extra_labels_add'
in targets.json.
3. Fix pin name table according to the classification.
4. Fix pinmap table according to the classification.
Chun-Chieh Li
Martin Kojtal
int_szyk
cyliangtw