3.5.1 Dev update

README.md

@@ -128,6 +128,10 @@ NEED TO FIX FOR THIS RELEASE.
 * check rs serial adapter is active if light color mode 11 is used.
 -->
 
+
+# Updates in 2.5.1 (dev)
+* Added scheduling of pump after events (Power On, Freeze Protect, Boost)
+
 # Updates in 2.5.0
 * PDA panel Rev 6.0 or newer that do not have a Jandy iAqualink device attached can use the AqualinkTouch protocol rather than PDA protocol.
   * This is faster, more reliable and does not intefear with the physical PDA device (like existing implimentation) 

release/aqualinkd.conf

@@ -161,6 +161,15 @@ rs485_frame_delay = 0
 # If you used the install script and didn;t receive any cron warnings, you should be good to go.
 enable_scheduler = yes
 
+# Check if button_01 (usually Pump) is scheduled to run after an event that may have turned it off, and set it to run.
+# Only for RS panels, Will not work for PDA panles.
+# Example below is if pump is off due to power reset, freezeprotect/swg boots turned off between 6am and 11pm turn the pump on.
+#scheduler_check_pumpon_hour = 6
+#scheduler_check_pumpoff_hour = 23
+#scheduler_check_poweron = yes
+#scheduler_check_freezeprotectoff = yes
+#scheduler_check_boostoff = yes
+
 # Put AqualinkD to sleep when in PDA mode after inactivity. 
 # Ignore if you are not using PDA mode.
 # If you have Jandy PDA then this MUST be set to yes as the controller can only support one PDA.

source/allbutton.c

@@ -9,6 +9,7 @@
 #include "devices_jandy.h"
 #include "allbutton_aq_programmer.h"
 #include "color_lights.h"
+#include "aq_scheduler.h"
 
 /* Below can also be called from serialadapter.c */
 void processLEDstate(struct aqualinkdata *aq_data, unsigned char *packet, logmask_t from)
@@ -223,8 +224,14 @@ void _processMessage(char *message, struct aqualinkdata *aq_data, bool reset)
     aq_data->last_display_message[1] = '\0';
 
     // Anything that wasn't on during the last set of messages, turn off
-    if ((msg_loop & MSG_FREEZE) != MSG_FREEZE)
+    if ((msg_loop & MSG_FREEZE) != MSG_FREEZE) {
-       aq_data->frz_protect_state = default_frz_protect_state;
+      if (aq_data->frz_protect_state != default_frz_protect_state) {
+        LOG(ALLB_LOG,LOG_INFO, "Freeze protect turned off\n");
+        event_happened_set_device_state(FREEZE_PROTECT_OFF, aq_data);
+        // Add code to check Pump if to turn it on (was scheduled) ie time now is inbetween ON / OFF schedule 
+      }
+      aq_data->frz_protect_state = default_frz_protect_state;
+    }
 
     if ((msg_loop & MSG_SERVICE) != MSG_SERVICE &&
         (msg_loop & MSG_TIMEOUT) != MSG_TIMEOUT ) {
@@ -277,6 +284,11 @@ void _processMessage(char *message, struct aqualinkdata *aq_data, bool reset)
     }
     */
     if ((msg_loop & MSG_BOOST) != MSG_BOOST) {
+      if (aq_data->boost == true) {
+        LOG(ALLB_LOG,LOG_INFO, "Boost turned off\n");
+        event_happened_set_device_state(BOOST_OFF, aq_data);
+        // Add code to check Pump if to turn it on (was scheduled) ie time now is inbetween ON / OFF schedule
+      }
       aq_data->boost = false;
       aq_data->boost_msg[0] = '\0';
       aq_data->boost_duration = 0;
@@ -420,7 +432,8 @@ void _processMessage(char *message, struct aqualinkdata *aq_data, bool reset)
   else if (stristr(msg, LNG_MSG_FREEZE_PROTECTION_ACTIVATED) != NULL)
   {
     msg_loop |= MSG_FREEZE;
-    aq_data->frz_protect_state = default_frz_protect_state;
+    //aq_data->frz_protect_state = default_frz_protect_state;
+    aq_data->frz_protect_state = ON;
     //freeze_msg_count = 0;
     strcpy(aq_data->last_display_message, msg); // Also display the message on web UI
   }
@@ -502,6 +515,7 @@ void _processMessage(char *message, struct aqualinkdata *aq_data, bool reset)
     {
       //LOG(ALLBUTTON,LOG_NOTICE, "Standard protocol initialization complete\n");
       queueGetProgramData(ALLBUTTON, aq_data);
+      event_happened_set_device_state(POWER_ON, aq_data);
       //queueGetExtendedProgramData(ALLBUTTON, aq_data, _aqconfig_.use_panel_aux_labels);
       _initWithRS = true;
     }

source/aq_scheduler.c

@@ -27,6 +27,7 @@
 #include "aqualink.h"
 #include "aq_scheduler.h"
 #include "config.h"
+#include "aq_panel.h"
 //#include "utils.h"
 
 
@@ -287,3 +288,47 @@ int build_schedules_js(char* buffer, int size)
 
   return length;
 }
+
+bool event_happened_set_device_state(reset_event_type type, struct aqualinkdata *aq_data)
+{
+  // Check time is between hours.
+  bool scheduledOn = false;
+
+  time_t now = time(NULL);
+  struct tm *tm_struct = localtime(&now);
+
+  int hour = tm_struct->tm_hour;
+  if (hour >= _aqconfig_.sched_chk_pumpon_hour && hour < _aqconfig_.sched_chk_pumpoff_hour ) {
+    scheduledOn = true;
+  }
+
+  // Check event type.
+  switch(type){
+    case POWER_ON:
+      if (scheduledOn && _aqconfig_.sched_chk_poweron && aq_data->aqbuttons[0].led->state == OFF) {
+        LOG(SCHD_LOG,LOG_INFO, "Powered on, schedule is set for pump running and pump is off, turning pump on\n");
+        panel_device_request(aq_data, ON_OFF, 0, true, NET_TIMER);
+      } else {
+        LOG(SCHD_LOG,LOG_DEBUG, "Powered on, schedule is not set and/or pump is already on, leaving\n");
+      }
+    break;
+    case FREEZE_PROTECT_OFF:
+      if (scheduledOn && _aqconfig_.sched_chk_freezeprotectoff && aq_data->aqbuttons[0].led->state == OFF) {
+        LOG(SCHD_LOG,LOG_INFO, "Freeze Protect off, schedule is set for pump running and pump is off, turning pump on\n");
+        panel_device_request(aq_data, ON_OFF, 0, true, NET_TIMER);
+      } else {
+        LOG(SCHD_LOG,LOG_DEBUG, "Freeze Protect off, schedule is not set and/or pump is already on, leaving\n");
+      }
+    break;
+    case BOOST_OFF:
+      if (scheduledOn && _aqconfig_.sched_chk_boostoff && aq_data->aqbuttons[0].led->state == OFF) {
+        LOG(SCHD_LOG,LOG_INFO, "Boost off, schedule is set for pump running and pump is off, turning pump on\n");
+        panel_device_request(aq_data, ON_OFF, 0, true, NET_TIMER);
+      } else {
+        LOG(SCHD_LOG,LOG_DEBUG, "Boost off, schedule is not set and/or pump is already on, leaving\n");
+      }
+    break;
+  }
+
+  return true;
+}

source/aq_scheduler.h

@@ -25,6 +25,14 @@ typedef struct aqs_cron
 
 int build_schedules_js(char* buffer, int size);
 int save_schedules_js(const char* inBuf, int inSize, char* outBuf, int outSize);
+
+typedef enum reset_event_type{
+  POWER_ON,
+  FREEZE_PROTECT_OFF,
+  BOOST_OFF
+} reset_event_type;
+
+bool event_happened_set_device_state(reset_event_type type, struct aqualinkdata *aq_data);
 //void read_schedules();
 //void write_schedules();
 

source/aqualink.h

@@ -228,7 +228,7 @@ typedef enum {
   NET_API, 
   NET_WS, 
   NET_DZMQTT,
-  NET_TIMER,       // Not used yet, need to change aq_timer.c
+  NET_TIMER,       // Timer or Scheduler (eg poweron/freezeprotect check)
   UNACTION_TIMER
 } request_source;
 

source/config.c

@@ -155,6 +155,13 @@ void init_parameters (struct aqconfig * parms)
 #endif
 
   parms->enable_scheduler = true;
+
+  parms->sched_chk_poweron = false;
+  parms->sched_chk_freezeprotectoff = false;
+  parms->sched_chk_boostoff = false;
+  parms->sched_chk_pumpon_hour = 0;
+  parms->sched_chk_pumpoff_hour = 0;
+
   parms->ftdi_low_latency = true;
   parms->frame_delay = 0;
   parms->device_pre_state = true;
@@ -682,6 +689,21 @@ bool setConfigValue(struct aqualinkdata *aqdata, char *param, char *value) {
   } else if (strncasecmp (param, "enable_scheduler", 16) == 0) {
     _aqconfig_.enable_scheduler = text2bool(value);
     rtn=true;
+  } else if (strncasecmp (param, "scheduler_check_poweron", 23) == 0) {
+    _aqconfig_.sched_chk_poweron = text2bool(value);
+    rtn=true;
+  } else if (strncasecmp (param, "scheduler_check_freezeprotectoff", 32) == 0) {
+    _aqconfig_.sched_chk_freezeprotectoff = text2bool(value);
+    rtn=true;
+  } else if (strncasecmp (param, "scheduler_check_boostoff", 24) == 0) {
+    _aqconfig_.sched_chk_boostoff = text2bool(value);
+    rtn=true;
+  } else if (strncasecmp (param, "scheduler_check_pumpon_hour", 27) == 0) {
+    _aqconfig_.sched_chk_pumpon_hour = strtoul(value, NULL, 10);
+    rtn=true;
+  } else if (strncasecmp (param, "scheduler_check_pumpoff_hour", 28) == 0) {
+    _aqconfig_.sched_chk_pumpoff_hour = strtoul(value, NULL, 10);
+    rtn=true;
   } else if (strncasecmp (param, "ftdi_low_latency", 16) == 0) {
     _aqconfig_.ftdi_low_latency = text2bool(value);
     rtn=true;

source/config.h

@@ -105,6 +105,11 @@ struct aqconfig
   bool mqtt_timed_update;
   bool sync_panel_time;
   bool enable_scheduler;
+  bool sched_chk_poweron;
+  bool sched_chk_freezeprotectoff;
+  bool sched_chk_boostoff;
+  int  sched_chk_pumpon_hour;
+  int  sched_chk_pumpoff_hour;
   bool ftdi_low_latency;
   int frame_delay;
   bool device_pre_state;