---
layout: documentation
title: 10002041-130 - ZWave
---

{% include base.html %}

# 10002041-130 iO Cover for the Simon 100 schuko plug socket
This describes the Z-Wave device *10002041-130*, manufactured by *SimonTech S.L.U* with the thing type UID of ```simontech_10002041130_00_000```.

The device is in the category of *Power Outlet*, defining Small devices to be plugged into a power socket in a wall which stick there.

![10002041-130 product image](https://opensmarthouse.org/zwavedatabase/999/image/)


The 10002041-130 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

Once plugged to 10002432-039 This Front permits the direct control of a load plugged toggling it each time that the pushbutton is. It is also possible to control the load using Z- Wave devices.

### Inclusion Information

KeyPad long press (2s<t<30s) -> Central LED blinks until release of Pushbutton -> The Node Information Frame is sent via Z- Wave.

### Exclusion Information

KeyPad long press (2s<t<30s) -> Central LED blinks until release of Pushbutton -> The Node Information Frame is sent via Z- Wave.

## Channels

The following table summarises the channels available for the 10002041-130 -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Switch | switch_binary | switch_binary | Switch | Switch | 
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number | 
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number | 
| Electric meter (amps) | meter_current | meter_current | Energy | Number | 

### Switch
Switch the power on and off.

The ```switch_binary``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.

### Electric meter (watts)
Indicates the instantaneous power consumption.

The ```meter_watts``` channel is of type ```meter_watts``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (volts)
Indicates the instantaneous voltage.

The ```meter_voltage``` channel is of type ```meter_voltage``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (amps)
Indicates the instantaneous current consumption.

The ```meter_current``` channel is of type ```meter_current``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.



## Device Configuration

The following table provides a summary of the 13 configuration parameters available in the 10002041-130.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 1 | Association LED | Turns ON/OFF the Association LED |
| 2 | Custom consumption limit | Custom consumption limit |
| 3 | Beacon | Beacon LEDs |
| 10 | Delay ON | Delay |
| 11 | Activation TIME | Activation TIME |
| 13 | Lock Input |  |
| 15 | Reset | Reset default |
| 16 | Delay OFF | Delay OFF |
| 17 | Post Reset State | Load state after reset |
| 19 | Action When Pressing | Action when pressing |
| 20 | Identify | The center LED flashes |
| 21 | Charge Status | Charge status (read-only) |
| 27 | Long Press Key | Determines function of long press |

### Parameter 1: Association LED

Turns ON/OFF the Association LED

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Default |
| 255 | Center LED ON |

The manufacturer defined default value is ```0``` (Default).

This parameter has the configuration ID ```config_1_1_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 2: Custom consumption limit

Custom consumption limit
0x0001 - 0xFFFF -> Sets the power in Watts that is supported. (once the load is over, it is disconnected).
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Default |
| 255 | Power in Watts |

The manufacturer defined default value is ```0``` (Default).

This parameter has the configuration ID ```config_2_2``` and is of type ```INTEGER```.


### Parameter 3: Beacon

Beacon LEDs
0x01-0x63 (1-100%) -> Sets the intensity of the beacon LEDs.
The following option values may be configured, in addition to values in the range 0 to 99 -:

| Value  | Description |
|--------|-------------|
| 0 | Disables the beacon function |

The manufacturer defined default value is ```0``` (Disables the beacon function).

This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```.


### Parameter 10: Delay ON

Delay
  * 0x00 -> (Default) Disables timing
  * 0x01-0x7F -> Sets a timing with a range of (1-127sec)
  * 0x80-0xFE -> Sets a timing with range of (1-127min)
Values in the range 0 to 254 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_10_1``` and is of type ```INTEGER```.


### Parameter 11: Activation TIME

Activation TIME
  * 0x00 -> (Default) Disables timing
  * 0x01-0x7F -> Sets a timing with a range of (1-127sec)
  * 0x80-0xFE -> Sets a timing with range of (1-127min)
Values in the range 0 to 254 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_11_1``` and is of type ```INTEGER```.


### Parameter 13: Lock Input



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Default |
| 255 | Disables pushbutton |

The manufacturer defined default value is ```0``` (Default).

This parameter has the configuration ID ```config_13_1``` and is of type ```INTEGER```.


### Parameter 15: Reset

Reset default

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | All parameters except Long Pulse Lock. |
| 39015 | Restored to default |

The manufacturer defined default value is ```0``` (All parameters except Long Pulse Lock.).

This parameter has the configuration ID ```config_15_2_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 16: Delay OFF

Delay OFF
  * 0x00 -> (Default) Disables timing
  * 0x01-0x7F -> Sets a timing with a range of (1-127sec)
  * 0x80-0xFE -> Sets a timing with range of (1-127min)
Values in the range 0 to 254 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_16_1``` and is of type ```INTEGER```.


### Parameter 17: Post Reset State

Load state after reset

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Off After Reset |
| 255 | Activated After Reset |

The manufacturer defined default value is ```255``` (Activated After Reset).

This parameter has the configuration ID ```config_17_1``` and is of type ```INTEGER```.


### Parameter 19: Action When Pressing

Action when pressing

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Toggle |
| 1 | On |
| 2 | Off |

The manufacturer defined default value is ```0``` (Toggle).

This parameter has the configuration ID ```config_19_1``` and is of type ```INTEGER```.


### Parameter 20: Identify

The center LED flashes

Values in the range 255 to 255 may be set.

The manufacturer defined default value is ```255```.

This parameter has the configuration ID ```config_20_1_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 21: Charge Status

Charge status (read-only)

Values in the range 0 to 0 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_21_2``` and is of type ```INTEGER```.
This is a read only parameter.


### Parameter 27: Long Press Key

Determines function of long press

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Default |
| 255 | Reset Config Parameters |

The manufacturer defined default value is ```0``` (Default).

This parameter has the configuration ID ```config_27_1``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The 10002041-130 supports 2 association groups.

### Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Group 1 (Lifeline)
**COMMAND\_CLASS\_BASIC_REPORT**

It is sent to the associated nodes when the load changes state:

  * ON -> 0xFF
  * OFF -> 0x00

**COMMAND\_CLASS\_METER\_REPORT\_V4**

It is sent to the associated nodes when the power consumed varies more than 10%

Electric meter, Consumed, Watts, Size 4, Precision 1, Value (W)

**COMMAND\_CLASS\_DEVICE\_RESET\_LOCALLY_ NOTIFICATION**

The associated nodes are sent when the device is deleted from the Z-Wave network

Association group 1 supports 3 nodes.

### Group 2: ctrl

Group 2 (Control)
COMMAND\_CLASS\_BASIC_REPORT

It is sent to the associated nodes when the load changes state:

  * ON -> 0xFF
  * OFF -> 0x00

Association group 2 supports 20 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| |
| COMMAND_CLASS_METER_V3| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_VERSION_V2| |

### Documentation Links

* [User Manual](https://opensmarthouse.org/zwavedatabase/999/reference/escaneig-20190125-1000.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/999).