---
layout: documentation
title: SR-ZV9092A - ZWave
---

{% include base.html %}

# SR-ZV9092A Z-Wave Heating Thermostat
This describes the Z-Wave device *SR-ZV9092A*, manufactured by *Namron* with the thing type UID of ```namron_zv9092a_00_000```.

The device is in the category of *HVAC*, defining Air condition devices, Fans.

![SR-ZV9092A product image](https://opensmarthouse.org/zwavedatabase/1499/image/)


The SR-ZV9092A supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

Z-Wave 16A underfloor heating thermostat with a touch panel. Both internal and external temperature sensor supported.

### Inclusion Information

### Method 1:

Select **ZWAVE INFO** on Home Interface to enter into Z-Wave network management. Select **Add**, then short press button , the device will send out an inclusion request, **Status** will show “Inclusion...”. If there is no response from a gateway within 30 seconds, or if the inclusion failed, **Status** will show “Fail”. If included successfully, **Status** will show “Inclusion OK” and the device ID.

### Method 2:

Set the gateway into inclusion mode, make sure the device is already removed from previous network and reset the power of the device. The device will be included automatically.

### Exclusion Information

Select **Remove**, then short press button, the device will send out an exclusion request, **Status** will show “Exclusion...". If there is no response from a gateway within 30 seconds, or exclusion failed, **Status** will show “Fail”. If excluded successfully, **Status** will show “Exclusion OK” and the device ID will be displayed as 0.

### General Usage Information



## Channels

The following table summarises the channels available for the SR-ZV9092A -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature | 
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number | 
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number | 
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number | 
| Electric meter (amps) | meter_current | meter_current | Energy | Number | 
| Thermostat mode | thermostat_mode | thermostat_mode | Temperature | Number | 
| Operating State | thermostat_state | thermostat_state | Temperature | Number | 
| Setpoint (heating) | thermostat_setpoint | thermostat_setpoint | Heating | Number:Temperature | 
| Setpoint (dry air) | thermostat_setpoint | thermostat_setpoint | Heating | Number:Temperature | 
| Setpoint (auto) | thermostat_setpoint | thermostat_setpoint | Heating | Number:Temperature | 
| Setpoint (away) | thermostat_setpoint | thermostat_setpoint | Heating | Number:Temperature | 
| Alarm (heat) | alarm_heat | alarm_heat | Fire | Switch | 
| Alarm (power) | alarm_power | alarm_power | Energy | Switch | 
| Clock Time Offset | time_offset | time_offset | Time | Number | 
| Sensor (temperature) 1 | sensor_temperature1 | sensor_temperature | Temperature | Number:Temperature | 
| Thermostat mode 1 | thermostat_mode1 | thermostat_mode | Temperature | Number | 
| Operating State 1 | thermostat_state1 | thermostat_state | Temperature | Number | 
| Setpoint (heating) 1 | thermostat_setpoint1 | thermostat_setpoint | Heating | Number:Temperature | 
| Setpoint (dry air) 1 | thermostat_setpoint1 | thermostat_setpoint | Heating | Number:Temperature | 
| Setpoint (auto) 1 | thermostat_setpoint1 | thermostat_setpoint | Heating | Number:Temperature | 
| Setpoint (away) 1 | thermostat_setpoint1 | thermostat_setpoint | Heating | Number:Temperature | 
| Sensor (temperature) 2 | sensor_temperature2 | sensor_temperature | Temperature | Number:Temperature | 

### Sensor (temperature)
Indicates the current temperature.

The ```sensor_temperature``` channel is of type ```sensor_temperature``` and supports the ```Number:Temperature``` item and is in the ```Temperature``` category.

### Electric meter (kWh)
Indicates the energy consumption (kWh).

The ```meter_kwh``` channel is of type ```meter_kwh``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (watts)
Indicates the instantaneous power consumption.

The ```meter_watts``` channel is of type ```meter_watts``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (volts)
Indicates the instantaneous voltage.

The ```meter_voltage``` channel is of type ```meter_voltage``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (amps)
Indicates the instantaneous current consumption.

The ```meter_current``` channel is of type ```meter_current``` and supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Thermostat mode
Sets the thermostat.

The ```thermostat_mode``` channel is of type ```thermostat_mode``` and supports the ```Number``` item and is in the ```Temperature``` category.
The following state translation is provided for this channel to the ```Number``` item type -:

| Value | Label     |
|-------|-----------|
| 0 | Off |
| 1 | Heat |
| 2 | Cool |
| 3 | Auto |
| 4 | Aux Heat |
| 5 | Resume |
| 6 | Fan Only |
| 7 | Furnace |
| 8 | Dry Air |
| 9 | Moist Air |
| 10 | Auto Changeover |
| 11 | Heat Economy |
| 12 | Cool Economy |
| 13 | Away |

### Operating State
Sets the thermostat operating state.

The ```thermostat_state``` channel is of type ```thermostat_state``` and supports the ```Number``` item and is in the ```Temperature``` category.
The following state translation is provided for this channel to the ```Number``` item type -:

| Value | Label     |
|-------|-----------|
| 0 | Idle |
| 1 | Heating |
| 2 | Cooling |
| 3 | Fan Only |
| 4 | Pending Heat |
| 5 | Pending Cool |
| 6 | Vent / Economiser |

### Setpoint (heating)
Sets the thermostat setpoint.

The ```thermostat_setpoint``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Setpoint (dry air)
Sets the thermostat setpoint.

The ```thermostat_setpoint``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Setpoint (auto)
Sets the thermostat setpoint.

The ```thermostat_setpoint``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Setpoint (away)
Sets the thermostat setpoint.

The ```thermostat_setpoint``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Alarm (heat)
Indicates if a heat alarm is triggered.

The ```alarm_heat``` channel is of type ```alarm_heat``` and supports the ```Switch``` item and is in the ```Fire``` category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the ```Switch``` item type -:

| Value | Label     |
|-------|-----------|
| OFF | OK |
| ON | Alarm |

### Alarm (power)
Indicates if a power alarm is triggered.

The ```alarm_power``` channel is of type ```alarm_power``` and supports the ```Switch``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the ```Switch``` item type -:

| Value | Label     |
|-------|-----------|
| OFF | OK |
| ON | Alarm |

### Clock Time Offset
Provides the current time difference for the devices time.

The ```time_offset``` channel is of type ```time_offset``` and supports the ```Number``` item and is in the ```Time``` category.

### Sensor (temperature) 1
Indicates the current temperature.

The ```sensor_temperature1``` channel is of type ```sensor_temperature``` and supports the ```Number:Temperature``` item and is in the ```Temperature``` category.

### Thermostat mode 1
Sets the thermostat.

The ```thermostat_mode1``` channel is of type ```thermostat_mode``` and supports the ```Number``` item and is in the ```Temperature``` category.
The following state translation is provided for this channel to the ```Number``` item type -:

| Value | Label     |
|-------|-----------|
| 0 | Off |
| 1 | Heat |
| 2 | Cool |
| 3 | Auto |
| 4 | Aux Heat |
| 5 | Resume |
| 6 | Fan Only |
| 7 | Furnace |
| 8 | Dry Air |
| 9 | Moist Air |
| 10 | Auto Changeover |
| 11 | Heat Economy |
| 12 | Cool Economy |
| 13 | Away |

### Operating State 1
Sets the thermostat operating state.

The ```thermostat_state1``` channel is of type ```thermostat_state``` and supports the ```Number``` item and is in the ```Temperature``` category.
The following state translation is provided for this channel to the ```Number``` item type -:

| Value | Label     |
|-------|-----------|
| 0 | Idle |
| 1 | Heating |
| 2 | Cooling |
| 3 | Fan Only |
| 4 | Pending Heat |
| 5 | Pending Cool |
| 6 | Vent / Economiser |

### Setpoint (heating) 1
Sets the thermostat setpoint.

The ```thermostat_setpoint1``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Setpoint (dry air) 1
Sets the thermostat setpoint.

The ```thermostat_setpoint1``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Setpoint (auto) 1
Sets the thermostat setpoint.

The ```thermostat_setpoint1``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Setpoint (away) 1
Sets the thermostat setpoint.

The ```thermostat_setpoint1``` channel is of type ```thermostat_setpoint``` and supports the ```Number:Temperature``` item and is in the ```Heating``` category.

### Sensor (temperature) 2
Indicates the current temperature.

The ```sensor_temperature2``` channel is of type ```sensor_temperature``` and supports the ```Number:Temperature``` item and is in the ```Temperature``` category.



## Device Configuration

The following table provides a summary of the 22 configuration parameters available in the SR-ZV9092A.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 2 | MaxCurrent | Overcurrent Protection |
| 3 | Feedback | Vibration and buzzer level |
| 4 | Recovery | Recovery after loss of power |
| 6 | MaxTemp | Overtemperature protection |
| 7 | Hysteresis | Temperature hysteresis |
| 8 | AutoModeControl | Auto mode temperature control |
| 9 | ExtSensorType | Floor temperature sensor type |
| 10 | Sensor | Temperature sensor selection |
| 11 | IntTempCorr | Room/internal temperature sensor correction |
| 12 | ExtTempCorr | Floor/external temperature sensor correction |
| 13 | DryingDuration | Drying mode duration |
| 14 | PostDryMode | Mode after drying cycle |
| 16 | ReportHysteresis | Temperature report hysteresis |
| 17 | ReportInterval | Periodic report interval for temperature and humidity |
| 18 | PowerReportHysteresis | Power report hysteresis |
| 19 | CurrentReportHysteresis | Current report hysteresis |
| 20 | VoltageReportHysteresis | Voltage report hysteresis |
| 21 | MeterReportInterval | Periodic report interval for the meter |
| 22 | Brightness | OLED display brightness |
| 23 | DisplaySensor | Display temperature sensor |
| 24 | TimeZone | Time zone UTC offset |
| 27 | DisplayAutoOff | Display auto off |

### Parameter 2: MaxCurrent

Overcurrent Protection
Maximum overcurrent detection value in A. When the detected current is over this value, the device will turn off the relay and send **NOTIFICATION CC**.

****: Disable overcurrent detection  
**5-16**: Maximum allowed current
Values in the range 0 to 16 may be set.

The manufacturer defined default value is ```16```.

This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```.


### Parameter 3: Feedback

Vibration and buzzer level
Vibration and buzzer level triggered by pressing buttons:

****: Disabled  
**1**: Low Level  
**2**: High Level
The following option values may be configured, in addition to values in the range 0 to 2 -:

| Value  | Description |
|--------|-------------|
| 0 | Disabled |
| 1 | Low |
| 2 | High |

The manufacturer defined default value is ```1``` (Low).

This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```.


### Parameter 4: Recovery

Recovery after loss of power
Whether to recover to settings from before power failure or power reset:

****: Use default settings  
**1**: Recover to settings before power failure or power reset
The following option values may be configured, in addition to values in the range 0 to 1 -:

| Value  | Description |
|--------|-------------|
| 0 | Use default settings |
| 1 | Recover to settings before power failure or power reset |

The manufacturer defined default value is ```1``` (Recover to settings before power failure or power reset).

This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```.


### Parameter 6: MaxTemp

Overtemperature protection
Maximum temperature detection value in °C. When either temperature sensor is above this value, the device will turn off the relay and send **NOTIFICATION CC**:

****: Disabled  
**20-60**: The maximum temperature in °C
Values in the range 0 to 60 may be set.

The manufacturer defined default value is ```45```.

This parameter has the configuration ID ```config_6_1``` and is of type ```INTEGER```.


### Parameter 7: Hysteresis

Temperature hysteresis
Temperature control hysteresis value setting, range is 0.5 °C to 2 °C with a unit of 0.1 °C:

**5**: Control hysteresis is 0.5 °C  
**6-19**: Control hysteresis is 0.6-1.9 °C  
**20**: Control hysteresis is 2 °C
Values in the range 5 to 20 may be set.

The manufacturer defined default value is ```5```.

This parameter has the configuration ID ```config_7_1``` and is of type ```INTEGER```.


### Parameter 8: AutoModeControl

Auto mode temperature control
Auto mode (energy save mode) temperature schedule:

****: Use schedule set by user  
**1**: Use **Energy\_Save\_Heating** temperature set by **THERMOSTAT\_SETPOINT\_SET**
The following option values may be configured, in addition to values in the range 0 to 1 -:

| Value  | Description |
|--------|-------------|
| 0 | Use schedule set by user |
| 1 | Use Energy\_Save\_Heating temperature set by THERMOSTAT\_SETPOINT\_SET |

The manufacturer defined default value is ```0``` (Use schedule set by user).

This parameter has the configuration ID ```config_8_1``` and is of type ```INTEGER```.


### Parameter 9: ExtSensorType

Floor temperature sensor type
Floor temperature sensor type:

**1**: NTC/10K B(25/50°C)=3950  
**2**: NTC/15K B(25/50°C)=3950  
**3**: NTC/50K B(25/50°C)=3950  
**4**: NTC/100K B(25/50°C)=3950  
**5**: NTC/12K B(25/50°C)=3950
The following option values may be configured, in addition to values in the range 1 to 5 -:

| Value  | Description |
|--------|-------------|
| 1 | NTC/10K B(25/50°C)=3950 |
| 2 | NTC/15K B(25/50°C)=3950 |
| 3 | NTC/50K B(25/50°C)=3950 |
| 4 | NTC/100K B(25/50°C)=3950 |
| 5 | NTC/12K B(25/50°C)=3950 |

The manufacturer defined default value is ```1``` (NTC/10K B(25/50°C)=3950).

This parameter has the configuration ID ```config_9_1``` and is of type ```INTEGER```.


### Parameter 10: Sensor

Temperature sensor selection
Temperature control reference sensor selection:

**1**: Room/internal sensor  
**2**: Floor/external sensor  
**3**: Room/internal and floor/external sensor
The following option values may be configured, in addition to values in the range 1 to 3 -:

| Value  | Description |
|--------|-------------|
| 1 | Room/internal sensor |
| 2 | Floor/external sensor |
| 3 | Room/internal and floor/external sensor |

The manufacturer defined default value is ```1``` (Room/internal sensor).

This parameter has the configuration ID ```config_10_1``` and is of type ```INTEGER```.


### Parameter 11: IntTempCorr

Room/internal temperature sensor correction
Room/internal sensor temperature correction from -10 to 10 with 0.5 °C unit. This makes the effective range -5 °C to +5 °C.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode.
Values in the range -10 to 10 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_11_1``` and is of type ```INTEGER```.


### Parameter 12: ExtTempCorr

Floor/external temperature sensor correction
Floor/external sensor temperature correction from -10 to 10 with 0.5 °C unit. This makes the effective range -5 °C to +5 °C.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode.
Values in the range -10 to 10 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_12_1``` and is of type ```INTEGER```.


### Parameter 13: DryingDuration

Drying mode duration
Set how long the drying mode lasts, from 5 to 100 minutes.
Values in the range 5 to 100 may be set.

The manufacturer defined default value is ```30```.

This parameter has the configuration ID ```config_13_1``` and is of type ```INTEGER```.


### Parameter 14: PostDryMode

Mode after drying cycle
Set the mode after the drying mode ends:

****: Off  
**1**: Manual mode (Comfort mode)  
**2**: Auto mode (Energy Save mode)  
**3**: Away mode
Values in the range 1 to 3 may be set.

The manufacturer defined default value is ```2```.

This parameter has the configuration ID ```config_14_1``` and is of type ```INTEGER```.


### Parameter 16: ReportHysteresis

Temperature report hysteresis
Temperature report hysteresis setting, range is 0.1 °C to 1 °C with a unit of 0.1 °C:

****: Reporting disabled  
**2-10**: Report hysteresis is 0.1-1 °C
Values in the range 0 to 10 may be set.

The manufacturer defined default value is ```2```.

This parameter has the configuration ID ```config_16_1``` and is of type ```INTEGER```.


### Parameter 17: ReportInterval

Periodic report interval for temperature and humidity
Time interval for periodic report of temperature and humidity in seconds.

****: Periodic report disabled  
**30-28800**: Time interval is between 30 seconds and 8 hours
Values in the range 0 to 28800 may be set.

The manufacturer defined default value is ```300```.

This parameter has the configuration ID ```config_17_2``` and is of type ```INTEGER```.


### Parameter 18: PowerReportHysteresis

Power report hysteresis
Power report hysteresis setting in watts:

****: Reporting disabled  
**1-100**: Report hysteresis is 1-100 watt.
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```5```.

This parameter has the configuration ID ```config_18_1``` and is of type ```INTEGER```.


### Parameter 19: CurrentReportHysteresis

Current report hysteresis
Current report hysteresis setting in 0.1 ampere:

****: Reporting disabled  
**1-10**: Report hysteresis is 0.1-1 ampere.
Values in the range 0 to 10 may be set.

The manufacturer defined default value is ```10```.

This parameter has the configuration ID ```config_19_1``` and is of type ```INTEGER```.


### Parameter 20: VoltageReportHysteresis

Voltage report hysteresis
Voltage report hysteresis setting in volt:

****: Reporting disabled  
**1-10**: Report hysteresis is 1-10 volt.
Values in the range 0 to 10 may be set.

The manufacturer defined default value is ```2```.

This parameter has the configuration ID ```config_20_1``` and is of type ```INTEGER```.


### Parameter 21: MeterReportInterval

Periodic report interval for the meter
Time interval for periodic report of meter:

**60-2678400**: Time interval is between 1 minute and 31 days
Values in the range 60 to 2678400 may be set.

The manufacturer defined default value is ```600```.

This parameter has the configuration ID ```config_21_4``` and is of type ```INTEGER```.


### Parameter 22: Brightness

OLED display brightness
OLED display brightness when operating the device:

****: Low level**  
1**: Mid level**  
2**: High level
The following option values may be configured, in addition to values in the range 0 to 2 -:

| Value  | Description |
|--------|-------------|
| 0 | Low |
| 1 | Medium |
| 2 | High |

The manufacturer defined default value is ```1``` (Medium).

This parameter has the configuration ID ```config_22_1``` and is of type ```INTEGER```.


### Parameter 23: DisplaySensor

Display temperature sensor
Defines which temperature sensor will be displayed on the Home page:

****: Room/internal temperature  
**1**: Floor/external temperature
The following option values may be configured, in addition to values in the range 0 to 1 -:

| Value  | Description |
|--------|-------------|
| 0 | Room/internal temperature |
| 1 | Floor/external temperature |

The manufacturer defined default value is ```0``` (Room/internal temperature).

This parameter has the configuration ID ```config_23_1``` and is of type ```INTEGER```.


### Parameter 24: TimeZone

Time zone UTC offset
The time zone offset from UTC in hours, from -12 to 12.
Values in the range -12 to 12 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_24_1``` and is of type ```INTEGER```.


### Parameter 27: DisplayAutoOff

Display auto off
Enable or disable the display Auto off function when the interface is in standby:

****: Disabled  


**1**: Enabled
The following option values may be configured, in addition to values in the range 0 to 1 -:

| Value  | Description |
|--------|-------------|
| 0 | Disabled |
| 1 | Enabled |

The manufacturer defined default value is ```0``` (Disabled).

This parameter has the configuration ID ```config_27_1``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The SR-ZV9092A supports 2 association groups.

### Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Lifeline
1. Send Command Class **DEVICE\_RESET\_LOCALLY_NOTIFICATION** to associated devices of this group when factory reset the device.

2. Send Command Class **THERMOSTAT\_SETPOINT\_REPORT**, **THERMOSTAT\_MODE\_REPORT**, **THERMOSTAT\_OPERATING\_STATE_REPORT** to associated devices of this group when operation mode and temperature change.

3 .Send Command Class **NOTIFICATION_REPORT** to associated devices of this group when overcurrent or overheat detected.

4. Send Command Class **METER_REPORT** to associated devices of this group to report metering parameters.

Profile: AGI\_LIFE\_LINE (0x0001)

Association group 1 supports 1 node.

### Group 2: HeatSet

Heat set
Transfer Command Class **THERMOSTAT\_SETPOINT\_SET**, **THERMOSTAT\_MODE\_SET** to control other temperature control devices when operation changes.

Association group 2 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5| |
| COMMAND_CLASS_METER_V3| |
| COMMAND_CLASS_THERMOSTAT_MODE_V3| |
| COMMAND_CLASS_THERMOSTAT_OPERATING_STATE_V1| |
| COMMAND_CLASS_THERMOSTAT_SETPOINT_V2| |
| COMMAND_CLASS_TRANSPORT_SERVICE_V2| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_V4| |
| COMMAND_CLASS_SUPERVISION_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_ALARM_V8| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_VERSION_V3| |
| COMMAND_CLASS_TIME_PARAMETERS_V1| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |
| COMMAND_CLASS_SECURITY_V1| |
| COMMAND_CLASS_SECURITY_2_V1| |
#### Endpoint 1

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5| |
| COMMAND_CLASS_THERMOSTAT_MODE_V3| |
| COMMAND_CLASS_THERMOSTAT_OPERATING_STATE_V1| |
| COMMAND_CLASS_THERMOSTAT_SETPOINT_V2| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |
| COMMAND_CLASS_SECURITY_V1| |
#### Endpoint 2

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |
| COMMAND_CLASS_SECURITY_V1| |

### Documentation Links

* [User Manual](https://opensmarthouse.org/zwavedatabase/1499/reference/4512744_Namron_Termostat_Touch_Z-WAVE_16A_User_Manual.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/1499).