--- layout: documentation title: DB1 - ZWave --- {% include base.html %} # DB1 Alfred DB1 Digital Deadbolt Lock This describes the Z-Wave device *DB1*, manufactured by *Shenzhen Kaadas Intelligent Technology Co., Ltd* with the thing type UID of ```kaadas_db1_00_000```. The device is in the category of *Lock*, defining Devices whose primary pupose is locking something. ![DB1 product image](https://opensmarthouse.org/zwavedatabase/1575/image/) The DB1 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices. ## Overview Lock and unlock your door anywhere and anytime by integrate your lock into your Z-Wave home automation or security system for ultimate convenience. Features Bluetooth technology for added convenience with auto-unlock. ### Inclusion Information -Follow the user guide of hub to enter inclusion mode. -Operate on lock following guide below: 1. 1.Enter master mode(refer to programming instruction) 2. 2.Input “8” to enter “function extension settings” 3. 3.Input “1” to join a network. ### Exclusion Information -Follow the user guide of hub to enter exclusion mode. -Operate on lock following guide below: 1. 1.Enter master mode(refer to programming instruction) 2. 2.Input “8” to enter “function extension settings” 3. 3.Input “2” to log off a network. ### General Usage Information Factory Reset ※Please use this procedure only when the network primary controller is missing or inoperable. -Operations on lock 1. 1.Open the door and keep the lock in ""unlock"" status 2. 2.Open battery box and find the reset button. 3. 3.Use a sharp thing to press and hold the reset button. 4. 4.Keep holding the reset button and remove a battery from battery box then replace it. 5. 5.Keep holding the reset button until hearing voice guide. ## Channels The following table summarises the channels available for the DB1 -: | Channel Name | Channel ID | Channel Type | Category | Item Type | |--------------|------------|--------------|----------|-----------| | Door Lock | lock_door | lock_door | Door | Switch | | Alarm (access) | alarm_access | alarm_access | Door | Switch | | Battery Level | battery-level | system.battery_level | Battery | Number | | Clock Time Offset | time_offset | time_offset | Time | Number | ### Door Lock Lock and unlock the door. The ```lock_door``` channel is of type ```lock_door``` and supports the ```Switch``` item and is in the ```Door``` category. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | ON | Locked | | OFF | Unlocked | ### Alarm (access) Indicates if the access control alarm is triggered. The ```alarm_access``` channel is of type ```alarm_access``` and supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Battery Level Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading. The ```system.battery-level``` channel is of type ```system.battery-level``` and supports the ```Number``` item and is in the ```Battery``` category. This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%. ### Clock Time Offset Provides the current time difference for the devices time. The ```time_offset``` channel is of type ```time_offset``` and supports the ```Number``` item and is in the ```Time``` category. ## Device Configuration The device has no configuration parameters defined. ## Association Groups Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic. The DB1 supports 1 association group. ### Group 1: Lifeline The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Z-Wave Plus Lifeline Association group 1 supports 5 nodes. ## Technical Information ### Endpoints #### Endpoint 0 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_TRANSPORT_SERVICE_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_DOOR_LOCK_V1| | | COMMAND_CLASS_USER_CODE_V1| | | COMMAND_CLASS_SUPERVISION_V1| | | COMMAND_CLASS_ALARM_V8| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_POWERLEVEL_V1| | | COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| | | COMMAND_CLASS_BATTERY_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | | COMMAND_CLASS_TIME_V1| | | COMMAND_CLASS_TIME_PARAMETERS_V1| | | COMMAND_CLASS_SECURITY_V1| | | COMMAND_CLASS_SECURITY_2_V1| | ### Documentation Links * [Overview document](https://opensmarthouse.org/zwavedatabase/1575/reference/Alfred-DB1-C-insert-.pdf) * [Programming Instructions](https://opensmarthouse.org/zwavedatabase/1575/reference/DB1_Programming_Instructions_V22.0_EN.pdf) * [Z-Wave Plus System Integrators Guide](https://opensmarthouse.org/zwavedatabase/1575/reference/Alfred_Z-Wave_Plus_System_Integrators_GuideDB1_V1.2.pdf) --- Did you spot an error in the above definition or want to improve the content? You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/1575).