--- layout: documentation title: FGSS001 - ZWave --- {% include base.html %} # FGSS001 Smoke Sensor This describes the Z-Wave device *FGSS001*, manufactured by *[Fibargroup](http://www.fibaro.com/)* with the thing type UID of ```fibaro_fgss001_00_000```. The device is in the category of *Smoke Detector*, defining Smoke detectors. ![FGSS001 product image](https://opensmarthouse.org/zwavedatabase/134/image/) The FGSS001 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices. The FGSS001 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the *Wakeup Information* section below for further information. ## Overview The Fibaro Smoke Sensor is a universal, optical Z-Wave smoke sensor. The device can be hard wired (12 or 24 VDC) or battery operated (battery life 3 years*). Smoke detection is signaled through siren and LED diode blinking. Additionally, the smoke sensor signal can be sent to an alarm system or fire alarm system hub, through a NC (normally closed) contact terminals.  The optical sensor detects smoke at an early stage of fire, often before flames appear and temperature starts to rise significantly. Moreover the device has a built-in temperature sensor, which can also trigger the alarm once the specified temperatute threshold is exceeded.  The Fibaro Smoke Sensor is designed to be placed on a wall or ceiling. LED indicator signals fire, operating mode and used to see if device is within the Z-Wave network. The smoke sensor is designed to operate in confined spaces, under normal conditions (lacking smoke, dust, condensed water vapor) ### Inclusion Information Manual Fibaro Smoke Sensor inclusion: 1. Connect the power source to the Fibaro Smoke Detctor and/or install the battery. Make sure the device is located within direct range of the Z-Wave controller. 2. Set the main controller into the learn mode (see main controller’s operating manual). 3. Quickly, triple click the B-button, located on Fibaro Smoke Sensor’s enclosure. 4. Fibaro Smoke Sensor will be detected and included in the Z-Wave network. ### Exclusion Information 1. Make sure the sensor is connected to power source (battery and/or hard wired). 2. Set the main controller into the learn mode (see main controller’s operating manual) 3. Quickly, triple click the B-button, located on Fibaro Smoke Sensor’s enclosure ### Wakeup Information The FGSS001 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device. If the sensor is already included in the Z-Wave network, wake it up by triple clicking the B-button.. ## Channels The following table summarises the channels available for the FGSS001 -: | Channel Name | Channel ID | Channel Type | Category | Item Type | |--------------|------------|--------------|----------|-----------| | Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature | | Battery Level | battery-level | system.battery_level | Battery | Number | | Clock Time Offset | time_offset | time_offset | Time | Number | | Alarm (smoke) | alarm_smoke | alarm_smoke | Smoke | Switch | | Alarm (general) | alarm_general | alarm_general | Alarm | Switch | | Alarm (heat) | alarm_heat | alarm_heat | Fire | Switch | ### Sensor (temperature) Indicates the current temperature. The ```sensor_temperature``` channel is of type ```sensor_temperature``` and supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Battery Level Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading. The ```system.battery-level``` channel is of type ```system.battery-level``` and supports the ```Number``` item and is in the ```Battery``` category. This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%. ### Clock Time Offset Provides the current time difference for the devices time. The ```time_offset``` channel is of type ```time_offset``` and supports the ```Number``` item and is in the ```Time``` category. ### Alarm (smoke) Indicates if a smoke is triggered. The ```alarm_smoke``` channel is of type ```alarm_smoke``` and supports the ```Switch``` item and is in the ```Smoke``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Alarm (general) Indicates if an alarm is triggered. The ```alarm_general``` channel is of type ```alarm_general``` and supports the ```Switch``` item and is in the ```Alarm``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Alarm (heat) Indicates if a heat alarm is triggered. The ```alarm_heat``` channel is of type ```alarm_heat``` and supports the ```Switch``` item and is in the ```Fire``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ## Device Configuration The following table provides a summary of the 18 configuration parameters available in the FGSS001. Detailed information on each parameter can be found in the sections below. | Param | Name | Description | |-------|-------|-------------| | 1 | Alarm Cancellation Delay | Alarm Cancellation Delay | | 2 | Alarm acoustic and visual signals | Alarm acoustic and visual signals | | 5 | Type of alarm to 1st association group (SMOKE) | Type of alarm to 1st association group (SMOKE) | | 7 | Forced Level of Dimming group 1 | Forced Level of Dimming group 1 | | 10 | Interval between temperature readings | Interval between temperature readings | | 12 | Insensitiveness to temperature changes. | | | 13 | Frame broadcast mode | Frame broadcast mode | | 73 | Temperature measurement compensation | Temperature measurement compensation | | 80 | Z-Wave range test interval | Z-Wave range test interval | | 81 | Temperature alarm threshold | Temperature alarm threshold | | 82 | Smoke Sensor sensitivity | Smoke Sensor sensitivity | | 83 | Black Box sensitivity level | Black Box sensitivity level | | 84 | Malfunction alarm | Malfunction alarm | | 85 | Temperature alarm | Temperature alarm | | 86 | Lack of the Z-Wave range alarm | Lack of the Z-Wave range alarm | | 87 | Low battery alarm | Low battery alarm | | 88 | Temperature measurement compensation for report | Temperature measurement compensation for report | | 89 | Tamper alarm | Activates/inactivates temper switch alarm | | | Wakeup Interval | Sets the interval at which the device will accept commands from the controller | | | Wakeup Node | Sets the node ID of the device to receive the wakeup notifications | ### Parameter 1: Alarm Cancellation Delay Alarm Cancellation Delay Additional delay after an alarm has ceased. The parameter allows you to specify additional time, after which the alarm is cancelled once its violation has ceased. Values in the range 0 to 3600 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_1_2``` and is of type ```INTEGER```. ### Parameter 2: Alarm acoustic and visual signals Alarm acoustic and visual signals parameter allows for LED indicator and acoustic alarm deactivation in case of smoke detection The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | acoustic and visual alarms inactive | | 1 | acoustic alarm inactive, visual alarm active | | 2 | acoustic alarm active, visual alarm inactive | | 3 | acoustic and visual alarms active | The manufacturer defined default value is ```3``` (acoustic and visual alarms active). This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```. ### Parameter 5: Type of alarm to 1st association group (SMOKE) Type of alarm to 1st association group (SMOKE) Allows for choosing a command class used in 1-st Association Group. The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | ALARM SENSOR (SMOKE) | | 255 | BASIC_SET | The manufacturer defined default value is ```255``` (BASIC_SET). This parameter has the configuration ID ```config_5_1``` and is of type ```INTEGER```. ### Parameter 7: Forced Level of Dimming group 1 Forced Level of Dimming group 1 Value of the parameter specifying the forced level of dimming / opening sun blinds when comes 'switch on' / 'open' command to devices from association group no. 1 In the case of alarm frames the alarm priority is specified. Values in the range 1 to 255 may be set. The manufacturer defined default value is ```255```. This parameter has the configuration ID ```config_7_1``` and is of type ```INTEGER```. ### Parameter 10: Interval between temperature readings Interval between temperature readings Interval between successive readings of temperature from all sensors connected to the device in seconds. Note: taking temperature readings from the sensor does not result in sending a temperature condition report to the central hub. Values in the range 1 to 32767 may be set. The manufacturer defined default value is ```300```. This parameter has the configuration ID ```config_10_2``` and is of type ```INTEGER```. ### Parameter 12: Insensitiveness to temperature changes. Values in the range 0 to 100 may be set. The manufacturer defined default value is ```20```. This parameter has the configuration ID ```config_12_1``` and is of type ```INTEGER```. ### Parameter 13: Frame broadcast mode Frame broadcast mode Transmitting the alarm or control frame in 'broadcast' mode (i.e. to all devices within range), information sent in this mode is not repeated by the mesh network. **NOTE**: If the broadcast mode of information transmission is activated for a given  The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Broadcast inactive | | 1 | Smoke mode active, Tamper mode inactive | | 2 | Smoke mode inactive, Tamper mode active | | 3 | Smoke and Tamper broadcast mode active | The manufacturer defined default value is ```0``` (Broadcast inactive). This parameter has the configuration ID ```config_13_1``` and is of type ```INTEGER```. ### Parameter 73: Temperature measurement compensation Temperature measurement compensation Temperature value to be added to or deducted from the current measured temperature measured by internal temperature sensor in order to compensate the difference between air temperature and temperature measured at the ceiling level Available settings: -1000 -/+ 1000 (in 0,1 C steps) Values in the range -1000 to 1000 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_73_2``` and is of type ```INTEGER```. ### Parameter 80: Z-Wave range test interval Z-Wave range test interval Time period between the consecutive Z-Wave network range tests. Available settings: 0 – 144 (10min multiplier) [10min-24h] 0 – Z-Wave network range test inactive Default setting: 1 (10min) Values in the range 0 to 255 may be set. The manufacturer defined default value is ```1```. This parameter has the configuration ID ```config_80_1``` and is of type ```INTEGER```. ### Parameter 81: Temperature alarm threshold Temperature alarm threshold Temperature value, measured by the built-in temperature sensor which the temperature alarm is sent. Available settings: 0,2 - 100 * 0 – temperature alarm inactive * 2 - 100 – (2 - 100 C) Default setting: * 54 (54 C) Values in the range 0 to 100 may be set. The manufacturer defined default value is ```54```. This parameter has the configuration ID ```config_81_1``` and is of type ```INTEGER```. ### Parameter 82: Smoke Sensor sensitivity Smoke Sensor sensitivity There are 3 levels of sensitivity to smoke presence. Level 1 means the highest sensitivity. The following option values may be configured -: | Value | Description | |--------|-------------| | 1 | High | | 2 | Medium | | 3 | Low | The manufacturer defined default value is ```2``` (Medium). This parameter has the configuration ID ```config_82_1``` and is of type ```INTEGER```. ### Parameter 83: Black Box sensitivity level Black Box sensitivity level Parameter specifies temperature and smoke level after which the Black Box starts recording them. The following option values may be configured -: | Value | Description | |--------|-------------| | 1 | High | | 2 | Medium | | 3 | Low | The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_83_1``` and is of type ```INTEGER```. ### Parameter 84: Malfunction alarm Malfunction alarm Time interval in which malfuntion alarm, if detected, is repeated using visual and acoustic alarms. Available settings: * 1 - 255 (100 ms multiplier) [100ms-25,5s] * Default setting: 10 (1s)  Values in the range -126 to 127 may be set. The manufacturer defined default value is ```10```. This parameter has the configuration ID ```config_84_1``` and is of type ```INTEGER```. ### Parameter 85: Temperature alarm Temperature alarm Time interval in which temperature alarm, if detected, is repeated using visual and acoustic alarms. Available settings: * 1 - 255 (100 ms multiplier) [100ms-25,5s] * Default setting: 5 (500ms) Values in the range -126 to 127 may be set. The manufacturer defined default value is ```5```. This parameter has the configuration ID ```config_85_1``` and is of type ```INTEGER```. ### Parameter 86: Lack of the Z-Wave range alarm Lack of the Z-Wave range alarm Time interval in which lack of the Z-Wave network alarm, if detected, is repeated using visual and acoustic alarms. Available settings: * 1 - 17280 (5s multiplier) [5s-24h] * Default setting: 360 (30min) Values in the range 1 to 17280 may be set. The manufacturer defined default value is ```360```. This parameter has the configuration ID ```config_86_2``` and is of type ```INTEGER```. ### Parameter 87: Low battery alarm Low battery alarm Time interval in which low battery alarm, if detected, is repeated using visual and acoustic alarms. Available settings: * 1 - 17280 (5s multiplier) [5s-24h] * Default setting: 360 (30min) Values in the range 1 to 17280 may be set. The manufacturer defined default value is ```360```. This parameter has the configuration ID ```config_87_2``` and is of type ```INTEGER```. ### Parameter 88: Temperature measurement compensation for report Temperature measurement compensation for report Consider temperature measurement compensation (parameter 73) when sending temperature report. The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Ignore temperature compensation | | 1 | Include temperature compensation | The manufacturer defined default value is ```0``` (Ignore temperature compensation). This parameter has the configuration ID ```config_88_1``` and is of type ```INTEGER```. ### Parameter 89: Tamper alarm Activates/inactivates temper switch alarm The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Tamper alarm inactive | | 1 | Tamper alarm active, with cancellation option | | 2 | Tamper alarm active, without cancellation option | The manufacturer defined default value is ```1``` (Tamper alarm active, with cancellation option). This parameter has the configuration ID ```config_89_1``` and is of type ```INTEGER```. ### Wakeup Interval The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications. This setting is defined in *seconds*. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances. Note that this setting does not affect the devices ability to send sensor data, or notification events. This parameter has the configuration ID ```wakeup_interval``` and is of type ```INTEGER```. ### Wakeup Node When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact. This parameter has the configuration ID ```wakeup_node``` and is of type ```INTEGER```. ## Association Groups Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic. The FGSS001 supports 3 association groups. ### Group 1: Fire Status Association group 1 supports 5 nodes. ### Group 2: TMP Button Association group 2 supports 5 nodes. ### Group 3: Device Status Association group 3 supports 1 node. ## Technical Information ### Endpoints #### Endpoint 0 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SENSOR_MULTILEVEL_V1| | | COMMAND_CLASS_CRC_16_ENCAP_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_BATTERY_V1| | | COMMAND_CLASS_WAKE_UP_V1| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| | | COMMAND_CLASS_TIME_PARAMETERS_V1| | | COMMAND_CLASS_SENSOR_ALARM_V1| | ### Documentation Links * [User Manual](https://opensmarthouse.org/zwavedatabase/134/reference/FGSS-001-Smoke-Sensor-en-2-1-2-3.pdf) --- Did you spot an error in the above definition or want to improve the content? You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/134).