---
layout: documentation
title: ZW500D - ZWave
---

{% include base.html %}

# ZW500D Dimmer
This describes the Z-Wave device *ZW500D*, manufactured by *Wenzhou MTLC Electric Appliances Co.,Ltd.* with the thing type UID of ```enerwave_zw500d_00_000```.

The device is in the category of *Wall Switch*, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

![ZW500D product image](https://opensmarthouse.org/zwavedatabase/299/image/)


The ZW500D supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

The ZW500D Dimmer Switch is a perfect wireless manual and remote on/off/dim/ bright control replacement of regular on/off and dimmer switch, controlling incandescent, dimmable LED and CFL. This ZW500D dimmer switch is fully compatible with other Z-Wave devices, provides programmable function creating a perfect ambiance such as scenes, association, schedule event, etc. Also it can be added to most Z-Wave compliant controllers. Sliding Air-Gap switch to a totally disconnect power while replacing light bulbs and preventing from leakage current from the fixture(s). This ZW500D dimmer works with ZW3K 3-Way Auxiliary Switch that reducing energy consumption, enhancing the value of technology of your home, condominiums and apartment.

### Inclusion Information

When the primary controller sends the program command, press the button

### Exclusion Information

When the primary controller sends the program command, press the button

## Channels

The following table summarises the channels available for the ZW500D -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer | 

### Dimmer
The brightness channel allows to control the brightness of a light.
            It is also possible to switch the light on and off.

The ```switch_dimmer``` channel is of type ```switch_dimmer``` and supports the ```Dimmer``` item and is in the ```DimmableLight``` category.



## Device Configuration

The following table provides a summary of the 2 configuration parameters available in the ZW500D.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 1 | configure LED light state | configure LED light state |
| 2 | Reverse installed direction | Control if switch up is on or off |
|  | Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |

### Parameter 1: configure LED light state

configure LED light state
0 = LED off with load on

1 = LED on with load on
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED off with load on |
| 1 | LED on with load on |

The manufacturer defined default value is ```0``` (LED off with load on).

This parameter has the configuration ID ```config_1_1``` and is of type ```INTEGER```.


### Parameter 2: Reverse installed direction

Control if switch up is on or off
0 = normal install, up is on

1 = invert switch
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | normal install - up is on |
| 1 | invert switch |

The manufacturer defined default value is ```0``` (normal install - up is on).

This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```.

### Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -:
| Value  | Description |
|--------|-------------|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |

This parameter has the configuration ID ```switchall_mode``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZW500D supports 1 association group.

### Group 1: Group 1


Association group 1 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V2| Linked to BASIC|
| COMMAND_CLASS_SWITCH_ALL_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_ASSOCIATION_V1| |
| COMMAND_CLASS_VERSION_V1| |

### Documentation Links

* [User Manual](https://opensmarthouse.org/zwavedatabase/299/reference/ZW500D-11052014.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/299).