---
layout: documentation
title: 45603 - ZWave
---

{% include base.html %}

# 45603 Fluorescent Light & Appliance Module
This describes the Z-Wave device *45603*, manufactured by *Jasco Products* with the thing type UID of ```ge_45603_00_000```.

The device is in the category of *Power Outlet*, defining Small devices to be plugged into a power socket in a wall which stick there.

![45603 product image](https://opensmarthouse.org/zwavedatabase/42/image/)


The 45603 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

Jasco's Z-Wave Plug-In Lamp and Appliance Module allows you the option to adjust mood lighting for all occasions within your home. Z-Wave is a radio frequency, mesh network technology specifically designed for use in residential lighting control. Every Z-Wave enabled wall switch is capable of relaying commands and utilizes two-way communications to ensure reliable operation throughout the entire home. The open-air, line-of-sight transmission distance is up to 100-Feet between devices.

  * One Z-wave controlled AC outlet
  * Remote ON/OFF control via the Z-Wave controller
  * Manual ON/OFF control with the front panel pushbutton • One Always-ON pass-through AC outlet
  * Space efficient design
  * Does not block the lower outlet when plugged in to the upper outlet of a duplex wall receptacle. (This assumes that the duplex receptacle is mounted with the ground pin down.)
  * Plugs and cords for connected devices route to the side allowing close placement of furniture
  * Z-Wave certified

### Inclusion Information

  1. Plug ZW4101 into outlet
  2. Place controller in inclusion mode
  3. Press button on front of ZW4101

### Exclusion Information

  1. Plug ZW4101 into outlet
  2. Place controller in exclusion mode
  3. Press button on front of ZW4101

## Channels

The following table summarises the channels available for the 45603 -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Switch | switch_binary | switch_binary | Switch | Switch | 

### Switch
Switch the power on and off.

The ```switch_binary``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.



## Device Configuration

The following table provides a summary of the 2 configuration parameters available in the 45603.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 3 | Night Light | Defines the behavior of the blue LED; default has LED on when switch is off. |
| 4 | Invert Switch | Change the top of the switch to OFF and the bottom of the switch to ON. |

### Parameter 3: Night Light

Defines the behavior of the blue LED; default has LED on when switch is off.

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | LED on when switch is OFF |
| 1 | LED on when switch is ON |
| 2 | LED always off |

The manufacturer defined default value is ```0``` (LED on when switch is OFF).

This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```.


### Parameter 4: Invert Switch

Change the top of the switch to OFF and the bottom of the switch to ON.
Note: If you invert the switches and also install the product upside down, remember the load will now be controlled by the right, not the left switch.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | No |
| 1 | Yes |

The manufacturer defined default value is ```0``` (No).

This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.
## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_PROTECTION_V1| |
| COMMAND_CLASS_VERSION_V1| |

### Documentation Links

* [User Manual](https://opensmarthouse.org/zwavedatabase/42/reference/45603-Manual-Eng.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/42).