---
layout: documentation
title: AZL7434 - ZWave
---

{% include base.html %}

# AZL7434 In-wall Switch
This describes the Z-Wave device *AZL7434*, manufactured by *[Vision Security](http://www.visionsecurity.com.tw/)* with the thing type UID of ```vision_azl7434_05_001```.
This version of the device is limited to firmware version 5.1

The device is in the category of *Wall Switch*, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

![AZL7434 product image](https://opensmarthouse.org/zwavedatabase/558/image/)


The AZL7434 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

In-wall switch 1-relay

### Inclusion Information

Press 3 times on Program button within 2 seconds or turn on the wall switch 3 times within 2 seconds.

### Exclusion Information

Press 3 times on Program button within 2 seconds or turn on the wall switch within 2 seconds

## Channels

The following table summarises the channels available for the AZL7434 -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Switch | switch_binary | switch_binary | Switch | Switch | 

### Switch
Switch the power on and off.

The ```switch_binary``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.



## Device Configuration

The following table provides a summary of the 2 configuration parameters available in the AZL7434.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 1 | Mode | Mode |
| 2 | Switch Type | Switch Type |
|  | Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |

### Parameter 1: Mode

Mode
Configuration Value:

"1" -To Control Light with 1 Wall Switch & to Control Light With 2 WallSwitches.

"2"-To Control Light with 1 Wall Switch That Has Light Indicator (factory default).
Values in the range 1 to 2 may be set.

The manufacturer defined default value is ```2```.

This parameter has the configuration ID ```config_1_1``` and is of type ```INTEGER```.


### Parameter 2: Switch Type

Switch Type
Configuration Value:

"1" –With common on/off type switch button used(factory default).

"2"–With momentary type switch button used.
Values in the range 1 to 2 may be set.

The manufacturer defined default value is ```1```.

This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```.

### Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -:
| Value  | Description |
|--------|-------------|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |

This parameter has the configuration ID ```switchall_mode``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The AZL7434 supports 1 association group.

### Group 1: Group 1


Association group 1 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|
| COMMAND_CLASS_SWITCH_ALL_V1| |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_VERSION_V2| |
| COMMAND_CLASS_SECURITY_V1| |

### Documentation Links

* [User Manual](https://opensmarthouse.org/zwavedatabase/558/reference/AZL7434-In-wall-Switch.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/558).