--- layout: documentation title: FGK101 - ZWave --- {% include base.html %} # FGK101 Door Opening Sensor This describes the Z-Wave device *FGK101*, manufactured by *[Fibargroup](http://www.fibaro.com/)* with the thing type UID of ```fibaro_fgk101_03_002```. This version of the device is limited to firmware versions above 3.2 The device is in the category of *Door*, defining Door sensors. ![FGK101 product image](https://opensmarthouse.org/zwavedatabase/381/image/) The FGK101 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices. The FGK101 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the *Wakeup Information* section below for further information. ## Overview **FIBARO Door/Window Sensor** is a wireless, battery powered reed sensor compatible with the Z-Wave standard. Changing the device’s status will automatically send signal to the Z-Wave controller and associated devices.  Sensor can be used to trigger scenes and everywhere there is a need for information about opening or closing of doors, windows, garage doors, etc. Opening is detected by separating the sensor’s body and the magnet. In addition the FIBARO Door/Window Sensor supports one DS18B20 temperature sensor and has one potential free input. ### Inclusion Information Quickly, three times press the TMP button.  ### Exclusion Information Quickly, three times press the TMP button.  ### Wakeup Information The FGK101 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour. The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device. To wake up the sensor manually, click one of the TMP buttons (while the other button is pressed). ## Channels The following table summarises the channels available for the FGK101 -: | Channel Name | Channel ID | Channel Type | Category | Item Type | |--------------|------------|--------------|----------|-----------| | Scene Number | scene_number | scene_number | | Number | | Binary Sensor | sensor_binary | sensor_binary | | Switch | | Sensor (Temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature | | Door Sensor | sensor_door | sensor_door | Door | Contact | | Tamper Alarm | alarm_tamper | alarm_tamper | | Switch | | Battery Level | battery-level | system.battery_level | Battery | Number | | Alarm (general) | alarm_general | alarm_general | Alarm | Switch | ### Scene Number Triggers when a scene button is pressed. The ```scene_number``` channel is of type ```scene_number``` and supports the ```Number``` item. ### Binary Sensor Indicates if a sensor has triggered. The ```sensor_binary``` channel is of type ```sensor_binary``` and supports the ```Switch``` item. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | ON | Triggered | | OFF | Untriggered | ### Sensor (Temperature) Indicates the current temperature. The ```sensor_temperature``` channel is of type ```sensor_temperature``` and supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Door Sensor Indicates if the door/window is open or closed. The ```sensor_door``` channel is of type ```sensor_door``` and supports the ```Contact``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Contact``` item type -: | Value | Label | |-------|-----------| | OPEN | Open | | CLOSED | Closed | ### Tamper Alarm Indicates if the tamper alarm is triggered. The ```alarm_tamper``` channel is of type ```alarm_tamper``` and supports the ```Switch``` item. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Battery Level Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading. The ```system.battery-level``` channel is of type ```system.battery-level``` and supports the ```Number``` item and is in the ```Battery``` category. This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%. ### Alarm (general) Indicates if an alarm is triggered. The ```alarm_general``` channel is of type ```alarm_general``` and supports the ```Switch``` item and is in the ```Alarm``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ## Device Configuration The following table provides a summary of the 23 configuration parameters available in the FGK101. Detailed information on each parameter can be found in the sections below. | Param | Name | Description | |-------|-------|-------------| | 1 | Operations mode | Parameter defines device operation mode | | 2 | Door/Window or alarm status | Parameter defines state of the sensor when the magnet ... | | 3 | Visual LED indications | This parameter defines events indicated by the visual ... | | 4 | Range test after double click | Allows to enable activation of Z-Wave range test with ... | | 10 | 2nd association group triggers | Parameter defines events which result in sending on/off ... | | 11 | Commands sent to 2nd association group | Command frames sent to devices added to the 2nd association group. | | 12 | ON command sent to 2nd assoc. group | Value of ON command frame sent to 2nd association group | | 13 | OFF command sent to 2nd assoc. group | The value of 0 turns OFF the device, 255 turns it ON. | | 14 | Time delay of ON command frame | Time period after which ON command frame will be sent. | | 15 | Time delay of OFF command frame | Time period after which OFF command frame will be sent. | | 20 | Type of sent alarm frames | Type of control frames transmitted to the main controller ... | | 30 | Delay of tamper alarm cancellation | Time period after which a tamper alarm will be cancelled. | | 31 | Reporting tamper alarm cancellation | Reporting cancellation of tamper alarm to the controller ... | | 50 | Interval of temperature measurements | This parameter defines how often the temperature will ... | | 51 | Temperature reports threshold | This parameter defines the change of temperature in ... | | 52 | Interval of temperature reports | This parameter determines how often the temperature ... | | 53 | Temperature offset | The value to be added to the actual temperature, measured ... | | 54 | Temperature alarm reports | Temperature alarms reported to the Z-Wave controller. | | 55 | High temperature alarm threshold | If temperature is higher than set value, overheat ... | | 56 | Low temperature alarm threshold | If temperature is lower than the set value, underheat ... | | 70 | Scene activation functionality | The device can trigger scenes using scene IDs assigned ... | | 71 | Alarm broadcast | Settings for broadcasting ON/OFF commands, sensor ... | | 72 | Associations in Z-Wave network Security Mode | This parameter defines how commands are sent in ... | | | Wakeup Interval | Sets the interval at which the device will accept commands from the controller | | | Wakeup Node | Sets the node ID of the device to receive the wakeup notifications | ### Parameter 1: Operations mode Parameter defines device operation mode Available settings: 0 - Door/Window Sensor or external alarm sensor 1 - external button Values in the range 0 to 1 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_1_1``` and is of type ```INTEGER```. ### Parameter 2: Door/Window or alarm status Parameter defines state of the sensor when the magnet ... ... is close. If the alarm sensor is connected, it determines the output type. Parameter inactive in external button mode (parameter 1 set to 1). Available settings: 0 - Door/Window Sensor or external alarm sensor 1 - external button Values in the range 0 to 1 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```. ### Parameter 3: Visual LED indications This parameter defines events indicated by the visual ... ... LED indicator. Disabling events might extend battery life. Available settings: 0 - no indications 1 - indication of opening/closing status change (input IN) 2 - indication of wake up (1 x click or periodical) 4 - indication of device tampering Values in the range 0 to 6 may be set. The manufacturer defined default value is ```6```. This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```. ### Parameter 4: Range test after double click Allows to enable activation of Z-Wave range test with ... ... double click of a TMP button. Available settings: 0 - disabled 1 - enabled Values in the range 0 to 1 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```. ### Parameter 10: 2nd association group triggers Parameter defines events which result in sending on/off ... ... commands to devices added to the 2nd association group. These commands are sent alternately to switch the devices on and off. Commands represent the values of BASIC SET command frames. Parameter is inactive in external button mode (parameter 1 set to 1). Available settings: 0 - switch after opening and closing 1 - switch after opening 2 - switch after closing Values in the range 0 to 2 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_10_1``` and is of type ```INTEGER```. ### Parameter 11: Commands sent to 2nd association group Command frames sent to devices added to the 2nd association group. Available settings: 0 - ON 1 - OFF 2 - ON & OFF Values in the range 0 to 2 may be set. The manufacturer defined default value is ```2```. This parameter has the configuration ID ```config_11_1``` and is of type ```INTEGER```. ### Parameter 12: ON command sent to 2nd assoc. group Value of ON command frame sent to 2nd association group The value of 0 turns OFF the device, 255 turns it On. In case of associating the Dimmer or Roller Shutter module, values 1-99 allow to set an associated device to a specifed level. Values in the range 0 to 255 may be set. The manufacturer defined default value is ```255```. This parameter has the configuration ID ```config_12_2``` and is of type ```INTEGER```. ### Parameter 13: OFF command sent to 2nd assoc. group The value of 0 turns OFF the device, 255 turns it ON. In case of associating the Dimmer or Roller Shutter module, values 1-99 allow to set an associated device to a specified level The value of 0 turns OFF the device, 255 turns it On. In case of associating the Dimmer or Roller Shutter module, values 1-99 allow to set an associated device to a specifed level. Values in the range 0 to 255 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_13_2``` and is of type ```INTEGER```. ### Parameter 14: Time delay of ON command frame Time period after which ON command frame will be sent. Values in the range 0 to 32400 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_14_2``` and is of type ```INTEGER```. ### Parameter 15: Time delay of OFF command frame Time period after which OFF command frame will be sent. Values in the range 0 to 32400 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_15_2``` and is of type ```INTEGER```. ### Parameter 20: Type of sent alarm frames Type of control frames transmitted to the main controller ... ... and 3rd association group “Alarm”. If an external sensor is connected to IN input, it is possible to choose its functionality. Otherwise it is recommended to set this parameter to default value. Available settings: 0 - Door/Window Sensor (General Purpose Alarm) 1 - smoke sensor (Smoke Alarm) 2 - CO detector (CO Alarm) 3 - CO2 detector (CO2 Alarm) 4 - high temperature sensor (Heat Alarm) 5 - flood sensor (Water Alarm) Values in the range 0 to 5 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_20_1``` and is of type ```INTEGER```. ### Parameter 30: Delay of tamper alarm cancellation Time period after which a tamper alarm will be cancelled. Values in the range 0 to 32400 may be set. The manufacturer defined default value is ```5```. This parameter has the configuration ID ```config_30_2``` and is of type ```INTEGER```. ### Parameter 31: Reporting tamper alarm cancellation Reporting cancellation of tamper alarm to the controller ... ... and 5th association group. Available settings: 0 - do not send tamper cancellation report 1 - send tamper cancellation report Values in the range 0 to 1 may be set. The manufacturer defined default value is ```1```. This parameter has the configuration ID ```config_31_1``` and is of type ```INTEGER```. ### Parameter 50: Interval of temperature measurements This parameter defines how often the temperature will ... ... be measured. The shorter the time, the more frequently the temperature will be measured, but the battery life will shorten. Available settings: 0 - temperature measurements disabled 5-32400 - time in seconds Values in the range 0 to 32400 may be set. The manufacturer defined default value is ```300```. This parameter has the configuration ID ```config_50_2``` and is of type ```INTEGER```. ### Parameter 51: Temperature reports threshold This parameter defines the change of temperature in ... ...comparison with last reported, resulting in temperature report being sent to the main controller. Available settings: 0 - temperature reports based on threshold disabled 1-300 - temperature threshold (0.1-30°C, 0.1°C step) Values in the range 0 to 300 may be set. The manufacturer defined default value is ```10```. This parameter has the configuration ID ```config_51_2``` and is of type ```INTEGER```. ### Parameter 52: Interval of temperature reports This parameter determines how often the temperature ... ...  reports will be sent to the main controller. Available settings: 0 - periodic temperature reports disabled 5-32400 - time in seconds Values in the range 0 to 32400 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_52_2``` and is of type ```INTEGER```. ### Parameter 53: Temperature offset The value to be added to the actual temperature, measured ... ... by the sensor (temperature compensation). Available settings: -1000-1000 (-100-100°C, 0.1°C step) Values in the range -1000 to 1000 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_53_4``` and is of type ```INTEGER```. ### Parameter 54: Temperature alarm reports Temperature alarms reported to the Z-Wave controller. Thresholds are set in parameters 55 and 56. Available settings: 0 - temperature alarms disabled 1 - high temperature alarm 2 - low temperature alarm 3 - high and low temperature alarms enabled Values in the range 0 to 3 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_54_1``` and is of type ```INTEGER```. ### Parameter 55: High temperature alarm threshold If temperature is higher than set value, overheat ... ... notification will be sent and high temperature scene will be triggered (if activated). Available settings: 0-1000 (0-100°C, 0.1°C step) Values in the range 0 to 1000 may be set. The manufacturer defined default value is ```540```. This parameter has the configuration ID ```config_55_2``` and is of type ```INTEGER```. ### Parameter 56: Low temperature alarm threshold If temperature is lower than the set value, underheat ... ... notification will be sent and low temperature scene will be triggered (if activated). Available settings: -300-700 (-30-70°C, 0.1°C step) Values in the range -300 to 700 may be set. The manufacturer defined default value is ```40```. This parameter has the configuration ID ```config_56_2``` and is of type ```INTEGER```. ### Parameter 70: Scene activation functionality The device can trigger scenes using scene IDs assigned ... ... to different events. To deactivate all scenes set the value to 0. To activate all scenes set the value to 3903. Available settings: 1 - [ID 10] opening door/window (single click) 2 - [ID 11] closing door/window (single click) 4 - [ID 12] holding 8 - [ID 13] releasing 16 - [ID 14] double click 32 - [ID 15] triple click 256 - [ID 50] high temperature - door/window opened 512 - [ID 50] high temperature - door/window closed 1024 - [ID 51] low temperature - door/window opened 2048 - [ID 51] low temperature - door/window closed Values in the range 0 to 2048 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_70_2``` and is of type ```INTEGER```. ### Parameter 71: Alarm broadcast Settings for broadcasting ON/OFF commands, sensor ... ... alarm and tamper alarm. Value other than 0 means alarms are sent in Broadcast Mode, to all devices only within the range of the device. They are not repeated by the mesh network. Available settings: 0 - broadcasts inactive 1 - ON/OFF commands broadcast active 2 - sensor alarm broadcast active 4 - tamper alarm broadcast active Values in the range 0 to 4 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_71_1``` and is of type ```INTEGER```. ### Parameter 72: Associations in Z-Wave network Security Mode This parameter defines how commands are sent in ... ... specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st group “Lifeline”. Available settings: 0 - none of the groups sent as secure 1 - 2nd group ”Control” sent as secure 2 - 3rd group ”Alarm” sent as secure 4 - 4th group “Sensor ZW3” sent as secure 8 - 5th group “Tamper ZW3” sent as secure 15 - (all) Values in the range 0 to 15 may be set. The manufacturer defined default value is ```15```. This parameter has the configuration ID ```config_72_1``` and is of type ```INTEGER```. ### Wakeup Interval The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications. This setting is defined in *seconds*. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances. Note that this setting does not affect the devices ability to send sensor data, or notification events. This parameter has the configuration ID ```wakeup_interval``` and is of type ```INTEGER```. ### Wakeup Node When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact. This parameter has the configuration ID ```wakeup_node``` and is of type ```INTEGER```. ## Association Groups Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic. The FGK101 supports 5 association groups. ### Group 1: Lifeline The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Association group 1 supports 1 node. ### Group 2: Control Association group 2 supports 5 nodes. ### Group 3: Alarm Association group 3 supports 5 nodes. ### Group 4: Sensor ZW3 Association group 4 supports 5 nodes. ### Group 5: Tamper ZW3 Association group 5 supports 5 nodes. ## Technical Information ### Endpoints #### Endpoint 0 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_APPLICATION_STATUS_V1| | | COMMAND_CLASS_SCENE_ACTIVATION_V1| | | COMMAND_CLASS_SENSOR_BINARY_V1| | | COMMAND_CLASS_SENSOR_MULTILEVEL_V5| | | COMMAND_CLASS_CRC_16_ENCAP_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V1| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_BATTERY_V1| | | COMMAND_CLASS_WAKE_UP_V2| | | COMMAND_CLASS_ASSOCIATION_V1| | | COMMAND_CLASS_VERSION_V1| | | COMMAND_CLASS_SENSOR_ALARM_V1| | ### Documentation Links * [User Manual](https://opensmarthouse.org/zwavedatabase/381/reference/FGK-10x-EN-T-v2-0.pdf) --- Did you spot an error in the above definition or want to improve the content? You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/381).