---
layout: documentation
title: ZW97 - ZWave
---

{% include base.html %}

# ZW97 Eva Logik - Outdoor Smart Plug (2 channel)
This describes the Z-Wave device *ZW97*, manufactured by *NIE Technology* with the thing type UID of ```nietech_zw97_00_000```.

The device is in the category of *Power Outlet*, defining Small devices to be plugged into a power socket in a wall which stick there.

![ZW97 product image](https://opensmarthouse.org/zwavedatabase/1256/image/)


The ZW97 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

**Specifications**

Model: ZW97   
Power: 120VAC, 60Hz   
Loading : 15 Amp Smart Outlet*2   
Total(Both Outlets): 15 Amp   
Max Frequency: 908.42 MHz   
Operating Temperature: -4° F~122° F

**Introduction**

The EVA LOGIK ZW97 is a Z-Wave enabled 15A receptacle designed for using of most residential lighting and motor applications. It's compatible with LED, halogen, incandescent, xenon, fluorescent and compact fluorescent bulbs.The ZW97 fully works with the Fibaro, Smartthings, Wink hub as well as all other certified Z-Wave controllers.

One Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LED. Total load capacity for both outlets is 15A(1800W) Resistive.

### Inclusion Information

**Add to Z-Wave Network**

Put the Z-wave interface controller into “Add” mode, triple press the Program button (A). It will be included to network. (Once your controller confirmed, refresh the Z-Wave network to optimize performance. )

### Exclusion Information

**Remove from Z-Wave Network**

Put the Z-Wave interface controller into "Remove" mode, triple press the Program button (A). It will be excluded to network.

## Channels

The following table summarises the channels available for the ZW97 -:

| Channel Name | Channel ID | Channel Type | Category | Item Type |
|--------------|------------|--------------|----------|-----------|
| Switch | switch_binary | switch_binary | Switch | Switch | 
| Switch 1 | switch_binary1 | switch_binary | Switch | Switch | 
| Switch 2 | switch_binary2 | switch_binary | Switch | Switch | 

### Switch
Switch the power on and off.

The ```switch_binary``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.

### Switch 1
Switch the power on and off.

The ```switch_binary1``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.

### Switch 2
Switch the power on and off.

The ```switch_binary2``` channel is of type ```switch_binary``` and supports the ```Switch``` item and is in the ```Switch``` category.



## Device Configuration

The device has no configuration parameters defined.

## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.
## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_MULTI_CHANNEL_V2| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_VERSION_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |
#### Endpoint 1

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |
#### Endpoint 2

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC|
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1| |
| COMMAND_CLASS_ASSOCIATION_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3| |

### Documentation Links

* [Eva Logik ZW97 Product Manual](https://opensmarthouse.org/zwavedatabase/1256/reference/ZW97-manual-2019-12-24.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](https://opensmarthouse.org/zwavedatabase/1256).