---
layout: documentation
title: Schlage - ZWave
---

{% include base.html %}

# Schlage LE130
This describes the Z-Wave device *Schlage*, manufactured by *Trane Corporation* with the thing type UID of ```trane_le130_00_000```.

The device is in the category of *Remote Control*, defining Any portable or hand-held device that controls the status of something, e.g. remote control, keyfob etc..

![Schlage product image](https://www.cd-jackson.com/zwave_device_uploads/845/845_default.jpg)


The Schlage supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is unable to participate in the routing of data from other devices.

## Overview

LE130 REMOTE CONTROLLER FOR SPLIT-TYPE AIR CONDITIONERS

See user guide for IDs specific to each unit

### Inclusion Information

  1. Power on the remote
  2. Put the primary controller into inclusion mode (If you don’t know how to do this, refer to its manual).
  3. Hold down the Fan/Set buttons for 3 seconds
  4. If the inclusion is success, the LED will flash three times and the zwave wireless icon will light on the screen

### Exclusion Information

  1. Power on the remote
  2. Put the primary controller into excluison mode (If you don’t know how to do this, refer to its manual).
  3. Hold down the Fan/Set buttons for 3 seconds
  4. If the exclusion is success, the LED will flash three times and the zwave wireless icon will go out on the screen

## Channels

The following table summarises the channels available for the Schlage -:

| Channel | Channel Id | Category | Item Type |
|---------|------------|----------|-----------|
| Sensor (temperature) | sensor_temperature | Temperature | Number:Temperature | 
| Thermostat mode | thermostat_mode | Temperature | Number | 
| Setpoint (heating) | thermostat_setpoint | Temperature | Number:Temperature | 
| Setpoint (cooling) | thermostat_setpoint | Temperature | Number:Temperature | 
| Thermostat fan mode | thermostat_fanmode |  |  | 
| Battery Level | battery-level | Battery | Number |

### Sensor (temperature)

Indicates the current temperature.

The ```sensor_temperature``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category.

### Thermostat mode

Sets the thermostat.

The ```thermostat_mode``` channel supports the ```Number``` item and is in the ```Temperature``` category.
The following state translation is provided for this channel to the ```Number``` item type -:

| Value | Label     |
|-------|-----------|
| 0 | Off |
| 1 | Heat |
| 2 | Cool |
| 3 | Auto |
| 4 | Aux Heat |
| 5 | Resume |
| 6 | Fan Only |
| 7 | Furnace |
| 8 | Dry Air |
| 9 | Moist Air |
| 10 | Auto Changeover |
| 11 | Heat Economy |
| 12 | Cool Economy |
| 13 | Away |

### Setpoint (heating)

Sets the thermostat setpoint.

The ```thermostat_setpoint``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category.

### Setpoint (cooling)

Sets the thermostat setpoint.

The ```thermostat_setpoint``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category.

### Thermostat fan mode

Channel type information on this channel is not found.

### Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The ```battery-level``` channel supports the ```Number``` item and is in the ```Battery``` category.



## Device Configuration

The device has no configuration parameters defined.

## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.
## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1| |
| COMMAND_CLASS_THERMOSTAT_MODE_V1| |
| COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| |
| COMMAND_CLASS_THERMOSTAT_FAN_MODE_V1| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_BATTERY_V1| |
| COMMAND_CLASS_VERSION_V1| |

### Documentation Links

* [Device Manual](https://www.cd-jackson.com/zwave_device_uploads/845/LE130.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/845).