---
layout: documentation
title: SM-A702A - ZWave
---

{% include base.html %}

# SM-A702A Window/Door Sensor
This describes the Z-Wave device *SM-A702A*, manufactured by *Sigma Designs (Former Zensys)* with the thing type UID of ```sigma_sma702a_00_000```.

The device is in the category of *Sensor*, defining Device used to measure something.

![SM-A702A product image](https://www.cd-jackson.com/zwave_device_uploads/882/882_default.jpg)


The SM-A702A supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is unable to participate in the routing of data from other devices.

The SM-A702A does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the *Wakeup Information* section below for further information.

## Overview

Door/Window sensor with LED indicator, battery powered.

### Inclusion Information

Press Z-Wave button once to wake up the device then once to connect to Z-Wave network

### Exclusion Information

Press Z-Wave button once to wake up the device then once to disconect from Z-Wave network

### Wakeup Information

The SM-A702A does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.

The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.


Press Z-Wave button once to wake up the device

## Channels

The following table summarises the channels available for the SM-A702A -:

| Channel | Channel Id | Category | Item Type |
|---------|------------|----------|-----------|
| Binary Sensor | sensor_binary | Door | Switch | 
| Alarm (general) | alarm_general | Door | Switch | 
| Battery Level | battery-level | Battery | Number |

### Binary Sensor

Indicates if a sensor has triggered.

The ```sensor_binary``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the ```Switch``` item type -:

| Value | Label     |
|-------|-----------|
| ON | Triggered |
| OFF | Untriggered |

### Alarm (general)

Indicates if an alarm is triggered.

The ```alarm_general``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the ```Switch``` item type -:

| Value | Label     |
|-------|-----------|
| OFF | OK |
| ON | Alarm |

### Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The ```battery-level``` channel supports the ```Number``` item and is in the ```Battery``` category.



## Device Configuration

The device has no configuration parameters defined.

## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.
## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_BINARY_V2| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_ALARM_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_BATTERY_V1| |
| COMMAND_CLASS_WAKE_UP_V2| |
| COMMAND_CLASS_ASSOCIATION_V1| |
| COMMAND_CLASS_VERSION_V1| |

### Documentation Links

* [Installation Manual](https://www.cd-jackson.com/zwave_device_uploads/882/SM-A702A.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/882).