---
layout: documentation
title: 507801 - ZWave
---

{% include base.html %}

# 507801 CONNECT radio flush-mounted receiver, Roller shutter
This describes the Z-Wave device *507801*, manufactured by *Merten* with the thing type UID of ```merten_507801_00_000```.

The device is in the category of *Blinds*, defining Roller shutters, window blinds, etc..

![507801 product image](https://www.cd-jackson.com/zwave_device_uploads/617/617_default.jpg)


The 507801 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

### Inclusion Information

**Learn mode (for integration into Z-wave systems from other manufacturers):**

Triple click on the switch button within 1.5s

see also http://www.merten.de/uploads/tx\_seqdownload/V5078\_581\_00\_web.pdf

### Exclusion Information

1)

Press the switch button three times in quick succession (within approx 1.5 seconds) (Figure ! B; using an insulated tool such as an insulated phase tester. 

**The LED (Figure !A) flashes at intervals of one second.**

2)

Then press and hold the switch button until the LED stops flashing (approx. 5 seconds).

**The device has now been reset to its factory settings**

see also http://www.merten.de/uploads/tx\_seqdownload/V5078\_581\_00\_web.pdf

## Channels

The following table summarises the channels available for the 507801 -:

| Channel | Channel Id | Category | Item Type |
|---------|------------|----------|-----------|
| Blinds Control | blinds_control1 | Blinds | Rollershutter | 

### Blinds Control

Provides start / stop control of blinds.

The ```blinds_control1``` channel supports the ```Rollershutter``` item and is in the ```Blinds``` category.



## Device Configuration

The device has no configuration parameters defined.

## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The device does not support associations.
## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1| |
| COMMAND_CLASS_BASIC_WINDOW_COVERING_V1| |
| COMMAND_CLASS_MULTI_CHANNEL_V2| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_PROTECTION_V2| |
| COMMAND_CLASS_ASSOCIATION_V1| |
| COMMAND_CLASS_VERSION_V1| |
#### Endpoint 1

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC|
| COMMAND_CLASS_BASIC_WINDOW_COVERING_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_PROTECTION_V2| |
| COMMAND_CLASS_VERSION_V1| |
#### Endpoint 2

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC|
| COMMAND_CLASS_BASIC_WINDOW_COVERING_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_PROTECTION_V2| |
| COMMAND_CLASS_VERSION_V1| |

### Documentation Links

* [User Manual](https://www.cd-jackson.com/zwave_device_uploads/617/V5078-581-00-web.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/617).