---
layout: documentation
title: SmartDimmer - ZWave
---

{% include base.html %}

# SmartDimmer RAone SmartDimmer
This describes the Z-Wave device *SmartDimmer*, manufactured by *INNOVUS* with the thing type UID of ```innovus_00110001_01_000```.
This version of the device is limited to firmware versions above 1.0

The SmartDimmer supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

No device information is provided in the database. Consider [updating the database](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/62) to improve the documentation.

## Channels

The following table summarises the channels available for the SmartDimmer -:

| Channel | Channel Id | Category | Item Type |
|---------|------------|----------|-----------|
| Dimmer | switch_dimmer | DimmableLight | Dimmer | 
| Sensor (Power in watts) | sensor_power | Energy | Number | 
| Electric meter (kWh) | meter_kwh | Energy | Number | 
| Electric meter (watts) | meter_watts | Energy | Number | 

### Dimmer

The brightness channel allows to control the brightness of a light.
            It is also possible to switch the light on and off.

The ```switch_dimmer``` channel supports the ```Dimmer``` item and is in the ```DimmableLight``` category.

### Sensor (Power in watts)

Indicates the energy consumption (kWh).

The ```sensor_power``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (kWh)

Indicates the energy consumption (kWh).

The ```meter_kwh``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (watts)

Indicates the instantaneous power consumption.

The ```meter_watts``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.



## Device Configuration

The following table provides a summary of the 12 configuration parameters available in the SmartDimmer.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 0 | Maximum dim level | Maximum dim level |
| 1 | Report node | Report Node, reports changes in level to this node id. Disabled if 0. |
| 2 | B&O IR support | B&O IR support is disabled if 0 otherwise enabled. |
| 3 | Dimming type | Dimming Type, trailing edge enabled if 0 otherwise leading edge enabled. |
| 4 | Dimming level duration | Dimming level duration |
| 5 | Set level duration | Default Set Level Duration, how long time it takes to set one level in 0.01s. |
| 6 | Long dim duration | Long dim duration |
| 7 | Touch press time | Touch press time |
| 8 | Touch Multiple Press Time | No specific usage in this product |
| 9 | Touch Hold Time | Touch Hold Time |
| 10 | Network Update Interval | Network Update Interval |
| 11 | Rediscover Interval | Rediscover Interval, time between rediscoveries in 256 seconds. Disabled if 0. |
|  | Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |

### Parameter 0: Maximum dim level

Maximum dim level
Maximum Level, a limit on the maximum level the dimmer can reach. Levels larger than 99 will simply be interpreted as 99 ie. no limit.
Values in the range 0 to 99 may be set.

The manufacturer defined default value is ```99```.

This parameter has the configuration ID ```config_0_1``` and is of type ```INTEGER```.


### Parameter 1: Report node

Report Node, reports changes in level to this node id. Disabled if 0.

Values in the range 0 to 255 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_1_1``` and is of type ```INTEGER```.


### Parameter 2: B&O IR support

B&O IR support is disabled if 0 otherwise enabled.

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disabled |
| 1 | Enabled |

The manufacturer defined default value is ```1``` (enabled).

This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```.


### Parameter 3: Dimming type

Dimming Type, trailing edge enabled if 0 otherwise leading edge enabled.

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Trailing edge |
| 1 | Leading edge |

The manufacturer defined default value is ```1``` (Leading edge).

This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```.


### Parameter 4: Dimming level duration

Dimming level duration
Default Dimming Level Duration, how long time it takes to dim one level in 0.01s.
Values in the range 1 to 255 may be set.

The manufacturer defined default value is ```8```.

This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```.


### Parameter 5: Set level duration

Default Set Level Duration, how long time it takes to set one level in 0.01s.

Values in the range 1 to 255 may be set.

The manufacturer defined default value is ```1```.

This parameter has the configuration ID ```config_5_1``` and is of type ```INTEGER```.


### Parameter 6: Long dim duration

Long dim duration
Long Dim Duration, time to use dimming to level 0 when double clicking. Format is the same as multilevel switch duration.
Values in the range 0 to 255 may be set.

The manufacturer defined default value is ```158```.

This parameter has the configuration ID ```config_6_1``` and is of type ```INTEGER```.


### Parameter 7: Touch press time

Touch press time
Touch Press Time, time for presses to register as separate and not part of a sequence, measured in 0.01s. 0 is interpreted as a 1.
Values in the range 1 to 255 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_7_1``` and is of type ```INTEGER```.


### Parameter 8: Touch Multiple Press Time

No specific usage in this product
Touch Multiple Press Time, has no specific usage is this product, shouldn't be changed.
Values in the range 0 to 255 may be set.

The manufacturer defined default value is ```100```.

This parameter has the configuration ID ```config_8_1``` and is of type ```INTEGER```.


### Parameter 9: Touch Hold Time

Touch Hold Time
Touch Hold Time, time for presses to register as being held down in 0.01s. 0 is interpreted as a 1.
Values in the range 0 to 255 may be set.

The manufacturer defined default value is ```40```.

This parameter has the configuration ID ```config_9_1``` and is of type ```INTEGER```.


### Parameter 10: Network Update Interval

Network Update Interval
Network Update Interval, time between network updates in 256 seconds. Disabled if 0.
Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```168```.

This parameter has the configuration ID ```config_10_2``` and is of type ```INTEGER```.


### Parameter 11: Rediscover Interval

Rediscover Interval, time between rediscoveries in 256 seconds. Disabled if 0.

Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```2362```.

This parameter has the configuration ID ```config_11_2``` and is of type ```INTEGER```.

### Switch All Mode

Set the mode for the switch when receiving SWITCH ALL commands.

The following option values may be configured -:
| Value  | Description |
|--------|-------------|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |

This parameter has the configuration ID ```switchall_mode``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The SmartDimmer supports 1 association group.

### Group 1: Dimmer


Association group 1 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1| Linked to BASIC|
| COMMAND_CLASS_SWITCH_ALL_V1| |
| COMMAND_CLASS_SWITCH_TOGGLE_BINARY_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V1| |
| COMMAND_CLASS_METER_V2| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_POWERLEVEL_V1| |
| COMMAND_CLASS_PROTECTION_V1| |
| COMMAND_CLASS_NODE_NAMING_V1| |
| COMMAND_CLASS_ASSOCIATION_V1| |

### Documentation Links

* [Technical documentation](https://www.cd-jackson.com/zwave_device_uploads/62/smartdimmer-00110001-tech.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/62).