--- layout: documentation title: 014G0210 - ZWave --- {% include base.html %} # 014G0210 HC-Z Hydronic Floor Heating Controller This describes the Z-Wave device *014G0210*, manufactured by *Danfoss* with the thing type UID of ```danfoss_014g0210_00_000```. The device is in the category of *Radiator Control*, defining Controls on radiators used to heat up rooms. ![014G0210 product image](https://www.cd-jackson.com/zwave_device_uploads/935/935_default.jpg) The 014G0210 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network. ## Overview Product information "Danfoss HC10 (Hydronic contoller for 10 outputs)" The Danfoss HC (Hydronic Controller) is part of the wireless Z-wave controlsystems for heating systems in residential homes. The Danfoss HC allows the control of warmwater floor heating systems. The system offers a big bandwidth of advanced functions for optimal comfort and energy savings and allows a single room temperature control. The Danfoss HC includes among other things: 10 short circiut safe outputs for 24V actuator drives NC or NO, Relays for pump and boilercontrol, self-testing program, regulation by ON/OFF- or PWM-principle (pulse width modulation) etc. The system can exist of multiple Danfoss HC for bigger systems with more than 10 actuators drives. The Danfoss HC has a direct connector to a power supply of 230V. Because of that you do not need an additional transformer but all actuator drives will be supplied with 24V power.  **Features:** * Controlling of warmwater floor heating systems * 10 short circuit protected outputs with LED notice * Output for 24V actuator drive NC or NO * Guarantee of valve function at alle outputs even when there is temperatur control, every 14 day valve movement for ca. 12 minutes * Regulation by PWM-principle (pulse width modulation) * Relays for pump regulation with automatic 1 minute pump start-up on every third day, to avoid damages during the Standby time periods * Relays for boiler regulation, only active during warming needs * Automatic self diagnostics to show lost connection to the device * Wireless technologie: Z-Wave ### Inclusion Information To include the Hydronic Controller in Z-Wave follow the procedure: * Verify Hydronic Controller indicates "not included" on the MMI. * Activate "Inclusion" on the Z-Wave Controller * Press the button on the Hydronic Controller * Observe Hydronic Controller indicate included on the MMI ### Exclusion Information Exclusion can be done in two ways: **1. Initiated from the Controller** * Verify Hydronic Controller indicate "Included" on the MMI. "Fault" indication also covers "Included". * Activate "Exclusion" on the controller * Press the button on the Hydronic Controller * Observe Hydronic Controller indicate not included in a network on the MMI. **2. Initiated from the Hydronic Controller by a factory reset to default** * Verify the Hydronic Controller indicate "Included" or "Fault" on the MMI * Remove the mains power from the Hydronic Controller * Wait for 15 seconds * Press and hold the button while applying mains power. LED will light RED while leaving network. * Observe the Hydronic Controller indicate not included in a network on the MMI ## Channels The following table summarises the channels available for the 014G0210 -: | Channel | Channel Id | Category | Item Type | |---------|------------|----------|-----------| | Switch | switch_binary | Switch | Switch | | Thermostat mode | thermostat_mode | Temperature | Number | | Setpoint (heating) | thermostat_setpoint | Temperature | Number:Temperature | | Alarm | alarm_general | Door | Switch | | Thermostat mode 1 | thermostat_mode1 | Temperature | Number | | Setpoint (heating) 1 | thermostat_setpoint1 | Temperature | Number:Temperature | | Alarm 1 | alarm_general1 | Door | Switch | | Indicator 1 | indicator_flash1 | | Number | | Thermostat mode 2 | thermostat_mode2 | Temperature | Number | | Setpoint (heating) 2 | thermostat_setpoint2 | Temperature | Number:Temperature | | Alarm 2 | alarm_general2 | Door | Switch | | Thermostat mode 3 | thermostat_mode3 | Temperature | Number | | Setpoint (heating) 3 | thermostat_setpoint3 | Temperature | Number:Temperature | | Alarm 3 | alarm_general3 | Door | Switch | | Thermostat mode 4 | thermostat_mode4 | Temperature | Number | | Setpoint (heating) 4 | thermostat_setpoint4 | Temperature | Number:Temperature | | Alarm 4 | alarm_general4 | Door | Switch | | Thermostat mode 5 | thermostat_mode5 | Temperature | Number | | Setpoint (heating) 5 | thermostat_setpoint5 | Temperature | Number:Temperature | | Alarm 5 | alarm_general5 | Door | Switch | | Thermostat mode 6 | thermostat_mode6 | Temperature | Number | | Setpoint (heating) 6 | thermostat_setpoint6 | Temperature | Number:Temperature | | Alarm 6 | alarm_general6 | Door | Switch | | Thermostat mode 7 | thermostat_mode7 | Temperature | Number | | Setpoint (heating) 7 | thermostat_setpoint7 | Temperature | Number:Temperature | | Alarm 7 | alarm_general7 | Door | Switch | | Thermostat mode 8 | thermostat_mode8 | Temperature | Number | | Setpoint (heating) 8 | thermostat_setpoint8 | Temperature | Number:Temperature | | Alarm 8 | alarm_general8 | Door | Switch | | Thermostat mode 9 | thermostat_mode9 | Temperature | Number | | Setpoint (heating) 9 | thermostat_setpoint9 | Temperature | Number:Temperature | | Alarm 9 | alarm_general9 | Door | Switch | | Thermostat mode 10 | thermostat_mode10 | Temperature | Number | | Setpoint (heating) 10 | thermostat_setpoint10 | Temperature | Number:Temperature | | Alarm 10 | alarm_general10 | Door | Switch | | Switch 11 | switch_binary11 | Switch | Switch | | Switch 12 | switch_binary12 | Switch | Switch | ### Switch Switch the power on and off. The ```switch_binary``` channel supports the ```Switch``` item and is in the ```Switch``` category. ### Thermostat mode Sets the thermostat. The ```thermostat_mode``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) Sets the thermostat setpoint. The ```thermostat_setpoint``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm Indicates if an alarm is triggered. The ```alarm_general``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 1 Sets the thermostat. The ```thermostat_mode1``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 1 Sets the thermostat setpoint. The ```thermostat_setpoint1``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 1 Indicates if an alarm is triggered. The ```alarm_general1``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Indicator 1 Sets the number of indicator flash cycles. The ```indicator_flash1``` channel supports the ```Number``` item. ### Thermostat mode 2 Sets the thermostat. The ```thermostat_mode2``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 2 Sets the thermostat setpoint. The ```thermostat_setpoint2``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 2 Indicates if an alarm is triggered. The ```alarm_general2``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 3 Sets the thermostat. The ```thermostat_mode3``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 3 Sets the thermostat setpoint. The ```thermostat_setpoint3``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 3 Indicates if an alarm is triggered. The ```alarm_general3``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 4 Sets the thermostat. The ```thermostat_mode4``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 4 Sets the thermostat setpoint. The ```thermostat_setpoint4``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 4 Indicates if an alarm is triggered. The ```alarm_general4``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 5 Sets the thermostat. The ```thermostat_mode5``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 5 Sets the thermostat setpoint. The ```thermostat_setpoint5``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 5 Indicates if an alarm is triggered. The ```alarm_general5``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 6 Sets the thermostat. The ```thermostat_mode6``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 6 Sets the thermostat setpoint. The ```thermostat_setpoint6``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 6 Indicates if an alarm is triggered. The ```alarm_general6``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 7 Sets the thermostat. The ```thermostat_mode7``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 7 Sets the thermostat setpoint. The ```thermostat_setpoint7``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 7 Indicates if an alarm is triggered. The ```alarm_general7``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 8 Sets the thermostat. The ```thermostat_mode8``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 8 Sets the thermostat setpoint. The ```thermostat_setpoint8``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 8 Indicates if an alarm is triggered. The ```alarm_general8``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 9 Sets the thermostat. The ```thermostat_mode9``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 9 Sets the thermostat setpoint. The ```thermostat_setpoint9``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 9 Indicates if an alarm is triggered. The ```alarm_general9``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Thermostat mode 10 Sets the thermostat. The ```thermostat_mode10``` channel supports the ```Number``` item and is in the ```Temperature``` category. The following state translation is provided for this channel to the ```Number``` item type -: | Value | Label | |-------|-----------| | 0 | Off | | 1 | Heat | | 2 | Cool | | 3 | Auto | | 4 | Aux Heat | | 5 | Resume | | 6 | Fan Only | | 7 | Furnace | | 8 | Dry Air | | 9 | Moist Air | | 10 | Auto Changeover | | 11 | Heat Economy | | 12 | Cool Economy | | 13 | Away | ### Setpoint (heating) 10 Sets the thermostat setpoint. The ```thermostat_setpoint10``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category. ### Alarm 10 Indicates if an alarm is triggered. The ```alarm_general10``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Switch 11 Switch the power on and off. The ```switch_binary11``` channel supports the ```Switch``` item and is in the ```Switch``` category. ### Switch 12 Switch the power on and off. The ```switch_binary12``` channel supports the ```Switch``` item and is in the ```Switch``` category. ## Device Configuration The following table provides a summary of the 3 configuration parameters available in the 014G0210. Detailed information on each parameter can be found in the sections below. | Param | Name | Description | |-------|-------|-------------| | 1 | Valve Type | Type of Valve being controlled | | 2 | Heat Load Strategy | Set Head Load Strategy (0 = Stacking, 1 = Spreading) | | 3 | PWM period | Pulse-width modulation period | ### Parameter 1: Valve Type Type of Valve being controlled Parameter 1: Valve type: * 0 = Normal Closed (NC) default * 1 = Normal Open (NO) Mix of NC and NO types of valves is not supported Most systems use NC valves The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | NC | | 1 | NO | The manufacturer defined default value is ```0``` (NC). This parameter has the configuration ID ```config_1_1``` and is of type ```INTEGER```. ### Parameter 2: Heat Load Strategy Set Head Load Strategy (0 = Stacking, 1 = Spreading) Heat load strategy: * 0 = Stacking (default) * 1 = Spreading **Stacking**: * All endpoints where there are heat demand open at the same time at the start of each PWM period * Stacking is the default strategy **Spreading**: * The opening of valves is spread over the PWM period and may stretch into the next PWM period * Spreading is used in effort to: * Spread the demand for hot water over the PWM period * Spread the power demand for the valves (actuators) * Valves from different producers require different amount of energy. The power supply in the HC has limited capacity, and may not be able to feed all the valves at the same time (more about that later in ”Current limitation”) The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Stacking (Default) | | 1 | Spreading | The manufacturer defined default value is ```0``` (Stacking (Default)). This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```. ### Parameter 3: PWM period Pulse-width modulation period The PWM period can be set to 15, 30 or 60 seconds Set using the Configuration Command Class on each endpoint * 60 minutes PWM period * Is the default value * Intended for heavy floors * Thick concrete floors * Floors where the hot water pipes lie deep * 15 minutes PWM period * Intended for light floors * Wood floors * Floors where the hot water pipes lie close to the surface Based on the setpoint (target temperature) and the current room temperature, the HC control algorithm calculates how long portion of each PWM period the valve should be open to get to and maintain the target temperature The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | 15 minutes | | 1 | 30 minutes | | 2 | 60 minutes | The manufacturer defined default value is ```2``` (60 minutes). This parameter has the configuration ID ```config_3_1``` and is of type ```INTEGER```. ## Association Groups Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic. The 014G0210 supports 1 association group. ### Group 1: Lifeline The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. One group supported: 1 with profile "General-Life-line" * Lifeline for endpoints * Unsolicited reports: * Device Reset Locally Notification * Notification Report (Thermostat 1 only) Association group 1 supports 1 node. ## Technical Information ### Endpoints #### Endpoint 0 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| | | COMMAND_CLASS_SENSOR_MULTILEVEL_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| | | COMMAND_CLASS_MULTI_CHANNEL_V2| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 1 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 2 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 3 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 4 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 5 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 6 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 7 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 8 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 9 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 10 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_THERMOSTAT_MODE_V1| | | COMMAND_CLASS_THERMOSTAT_SETPOINT_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V7| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_INDICATOR_V1| | | COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2| | #### Endpoint 11 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| | #### Endpoint 12 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| | ### Documentation Links * [Quickstat Guide](https://www.cd-jackson.com/zwave_device_uploads/935/z-wave-danfoss-link-hc10-hydronic-controller-10-outputs-quickstart-guide.pdf) --- Did you spot an error in the above definition or want to improve the content? You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/935).