--- layout: documentation title: ZW139 - ZWave --- {% include base.html %} # ZW139 Nano Switch Gen5 (without meter) This describes the Z-Wave device *ZW139*, manufactured by *[AEON Labs](http://aeotec.com/)* with the thing type UID of ```aeon_zw139_00_000```. ![ZW139 product image](https://www.cd-jackson.com/zwave_device_uploads/648/648_default.jpg) The ZW139 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network. ## Overview Once installed behind a switch or socket, Nano Switch offers unparalleled wireless control via Z-Wave Plus. It lets you control, automate, and monitor ## Channels The following table summarises the channels available for the ZW139 -: | Channel | Channel Id | Category | Item Type | |---------|------------|----------|-----------| | Switch | switch_binary | Switch | Switch | | Scene Number | scene_number | | Number | | Alarm (heat) | alarm_heat | | Switch | | Clock Time Offset | time_offset | Temperature | Number | ### Switch Switch the power on and off. The ```switch_binary``` channel supports the ```Switch``` item and is in the ```Switch``` category. ### Scene Number Triggers when a scene button is pressed. The ```scene_number``` channel supports the ```Number``` item. ### Alarm (heat) Indicates if a heat alarm is triggered. The ```alarm_heat``` channel supports the ```Switch``` item. This is a read only channel so will only be updated following state changes from the device. The following state translation is provided for this channel to the ```Switch``` item type -: | Value | Label | |-------|-----------| | OFF | OK | | ON | Alarm | ### Clock Time Offset Provides the current time difference for the devices time. The ```time_offset``` channel supports the ```Number``` item and is in the ```Temperature``` category. ## Device Configuration The following table provides a summary of the 14 configuration parameters available in the ZW139. Detailed information on each parameter can be found in the sections below. | Param | Name | Description | |-------|-------|-------------| | 4 | Overheat protection | Overheat protection | | 20 | Output status after re-power | Configure the output status after re-power on it | | 80 | Group 1 notifications | Group 1 notifications when the state of Nano Switch's load is changed | | 81 | Group 3 notifications | Notification to sent for Group 3 when using the external switch 1 | | 82 | Group 4 notifications | Notification to sent for Group 4 when using the external switch 2 | | 83 | Configure the state of LED | Configure the state of LED when it is in 3 modes | | 84 | Night light mode LED state | Set the ON/OFF time of the LED when it is in Night light mode | | 86 | Set appointment 1 | Set the ON time of output load. | | 87 | Set appointment 2 | Set the OFF time of output load | | 120 | External switch mode for S1 | Configure the external switch mode for S1 | | 121 | External switch mode for S2 | Configure the external switch mode for S2 | | 122 | Control destination of external switch | Set the control destination for external switch | | 252 | Lock/unlock configuration parameters | Lock/unlock configuration parameters | | 255 | Reset the Nano Switch | | | | Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands | ### Parameter 4: Overheat protection Overheat protection The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | (Default) Disable | | 1 | Enable | The manufacturer defined default value is ```0``` ((Default) Disable). This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```. ### Parameter 20: Output status after re-power Configure the output status after re-power on it The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Last status | | 1 | Always on | | 2 | Always off | The manufacturer defined default value is ```0``` (Last status). This parameter has the configuration ID ```config_20_1``` and is of type ```INTEGER```. ### Parameter 80: Group 1 notifications Group 1 notifications when the state of Nano Switch's load is changed To set which notification would be sent to the associated devices (Group 1) when the state of Nano Switch's load is changed. The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Send Nothing | | 1 | Send Hail CC | | 2 | Send Basic Report CC | | 3 | Send Hail CC when using the manual switch to change the load | The manufacturer defined default value is ```3``` (Send Hail CC when using the manual switch to change the load). This parameter has the configuration ID ```config_80_1``` and is of type ```INTEGER```. ### Parameter 81: Group 3 notifications Notification to sent for Group 3 when using the external switch 1 To set which notification would be sent to the associated nodes in association Group 3 when using the external switch 1 to switch the loads. The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Send Nothing | | 1 | Send Basic Set CC | The manufacturer defined default value is ```1``` (Send Basic Set CC). This parameter has the configuration ID ```config_81_1``` and is of type ```INTEGER```. ### Parameter 82: Group 4 notifications Notification to sent for Group 4 when using the external switch 2 To set which notification would be sent to the associated nodes in association Group 4 when using the external switch 2 to switch the loads. The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Send Nothing | | 1 | Send Basic Set CC | The manufacturer defined default value is ```1``` (Send Basic Set CC). This parameter has the configuration ID ```config_82_1``` and is of type ```INTEGER```. ### Parameter 83: Configure the state of LED Configure the state of LED when it is in 3 modes Configure the state of LED when it is in 3 modes (Energy mode, Momentary indicate mode, Night light mode) The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Energy mode. The LED will follow the status (on/off) | | 1 | Momentary indicate mode | | 2 | Night light mode. The LED will remain ON state | The manufacturer defined default value is ```0``` (Energy mode. The LED will follow the status (on/off)). This parameter has the configuration ID ```config_83_1``` and is of type ```INTEGER```. ### Parameter 84: Night light mode LED state Set the ON/OFF time of the LED when it is in Night light mode 0 to 60 The minute time of OFF 256 to 316 The hour time of OFF 65536 to 65596 The minute time of ON 16777216 to 16777276 The hour time of ON Values in the range 0 to 16777276 may be set. The manufacturer defined default value is ```301991936```. This parameter has the configuration ID ```config_84_4``` and is of type ```INTEGER```. ### Parameter 86: Set appointment 1 Set the ON time of output load. 65536 to 65543 The day value (Mon to Sun) 16777216 Enable the setting. 256 to 316 The hour value of ON time 16777215 Disable the setting. 0 to 60 The minute value of ON time Values in the range 0 to 0 may be set. The manufacturer defined default value is ```8327680```. This parameter has the configuration ID ```config_86_4``` and is of type ```INTEGER```. ### Parameter 87: Set appointment 2 Set the OFF time of output load 256 to 316 The hour value of ON time 65536 to 65543 The day value (Mon to Sun) 16777215 Disable the setting. 0 to 60 The minute value of ON time 16777216 Enable the setting. Values in the range 0 to 16777216 may be set. The manufacturer defined default value is ```8327680```. This parameter has the configuration ID ```config_87_4``` and is of type ```INTEGER```. ### Parameter 120: External switch mode for S1 Configure the external switch mode for S1 The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Enter automatic identification mode | | 1 | 2-state switch mode | | 2 | 3 way switch mode | | 3 | Momentary push button mode | The manufacturer defined default value is ```0``` (Enter automatic identification mode). This parameter has the configuration ID ```config_120_1``` and is of type ```INTEGER```. ### Parameter 121: External switch mode for S2 Configure the external switch mode for S2 The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Enter automatic identification mode | | 1 | 2-state switch mode | | 2 | 3 way switch mode | | 3 | Momentary push button mode | The manufacturer defined default value is ```0``` (Enter automatic identification mode). This parameter has the configuration ID ```config_121_1``` and is of type ```INTEGER```. ### Parameter 122: Control destination of external switch Set the control destination for external switch The following option values may be configured -: | Value | Description | |--------|-------------| | 1 | control the output loads of itself | | 2 | control the other nodes | | 3 | control the output loads of itself and other nodes | The manufacturer defined default value is ```3``` (control the output loads of itself and other nodes). This parameter has the configuration ID ```config_122_1``` and is of type ```INTEGER```. ### Parameter 252: Lock/unlock configuration parameters Lock/unlock configuration parameters The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Unlock | | 1 | Lock | The manufacturer defined default value is ```0``` (Unlock). This parameter has the configuration ID ```config_252_1``` and is of type ```INTEGER```. ### Parameter 255: Reset the Nano Switch The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | (Default) Reset all configuration parameters | | 1431655765 | Reset and remove from network | The manufacturer defined default value is ```0``` ((Default) Reset all configuration parameters). This parameter has the configuration ID ```config_255_4``` and is of type ```INTEGER```. ### Switch All Mode Set the mode for the switch when receiving SWITCH ALL commands. The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Exclude from All On and All Off groups | | 1 | Include in All On group | | 2 | Include in All Off group | | 255 | Include in All On and All Off groups | This parameter has the configuration ID ```switchall_mode``` and is of type ```INTEGER```. ## Association Groups Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic. The ZW139 supports 4 association groups. ### Group 1: Z-Wave Plus Lifeline When the load state of Nano Switch (turn on/off the load) is changed, the Hail CC and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group. Association group 1 supports 5 nodes. ### Group 2: Forward Group 2 Forward the Basic Set, Switch All, Scene Activation Set to associated nodes in Group 2 when the Dual Nano Switch receives the Basic Set, Switch All, Scene Activation Set commands from main controller. (E.g. Send/forward Basic Set to control the other nodes in association Group 2) Association group 2 supports 5 nodes. ### Group 3: Send Basic Set to Group 3 Send Basic Set (configured by parameter 0x51 ) to the associated nodes in Group 3 when the external switch S1 is operated. Note: The Switch Mode of external switch S1 should be identified successfully, which means that the value of Configuration parameter 0x78 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S1 switch. Association group 3 supports 5 nodes. ### Group 4: Send Basic Set to Group 4 Send Basic Set (enabled by Configuration parameter 0x52) to the associated nodes in Group 4 when the external switch S2 is operated. Note: The Switch Mode of external switch S2 should be identified successfully, which means that the value of Configuration parameter 0x79 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S2 switch. Association group 4 supports 5 nodes. ## Technical Information ### Endpoints #### Endpoint 0 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_SWITCH_BINARY_V1| Linked to BASIC| | COMMAND_CLASS_SWITCH_ALL_V1| | | COMMAND_CLASS_SCENE_ACTIVATION_V1| | | COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1| | | COMMAND_CLASS_ZWAVEPLUS_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | | COMMAND_CLASS_ALARM_V4| | | COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| | | COMMAND_CLASS_POWERLEVEL_V1| | | COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1| | | COMMAND_CLASS_CLOCK_V1| | | COMMAND_CLASS_HAIL_V1| | | COMMAND_CLASS_ASSOCIATION_V2| | | COMMAND_CLASS_VERSION_V2| | ### Documentation Links * [Engineering Manual](https://www.cd-jackson.com/zwave_device_uploads/648/Engineering-Spec---Aeon-Labs-Dual-Nano-Switch.pdf) --- Did you spot an error in the above definition or want to improve the content? You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/648).