---
layout: documentation
title: ZW100 - ZWave
---

{% include base.html %}

# ZW100 MultiSensor 6
This describes the Z-Wave device *ZW100*, manufactured by *[AEON Labs](http://aeotec.com/)* with the thing type UID of ```aeon_zw100_01_007```.
This version of the device is limited to firmware version 1.7

The device is in the category of *Sensor*, defining Device used to measure something.

![ZW100 product image](https://www.cd-jackson.com/zwave_device_uploads/355/355_default.png)


The ZW100 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

Technical Specifications

  * Battery or USB powered PIR motion sensor, operating distance: Up to 500 feet/150 metres outdoors.
  * Operating temperature: 0°C to 40°C
  * Relative humidity: 8% RH to 80% RH

### Inclusion Information

Click one time:

  * Send non-security Node Info Frame
  * Add MultiSensor into Z-wave network (non security inclusion)

Short press 2 times within 1 second:

  * Send Security Node Info Frame
  * Add Multisensor into Z-Wave network (security inclusion)

### Exclusion Information

Click one time:

  * Send non-security Node Info Frame
  * Remove MultiSensor from Z-wave network

Short press 2 times within 1 second:

  * Send Security Node Info Frame
  * Remove MultiSensor from network

### General Usage Information

Press and hold for 20 seconds:

  * Reset MultiSensor to factory default (see documentation)

## Channels

The following table summarises the channels available for the ZW100 -:

| Channel | Channel Id | Category | Item Type |
|---------|------------|----------|-----------|
| Sensor (relative humidity) | sensor_relhumidity | Humidity | Number | 
| Sensor (ultraviolet) | sensor_ultraviolet | Temperature | Number | 
| Sensor (temperature) | sensor_temperature | Temperature | Number:Temperature | 
| Sensor (luminance) | sensor_luminance |  | Number | 
| Motion Alarm | alarm_motion | Door | Switch | 
| Tamper Alarm | alarm_tamper |  | Switch | 
| Battery Level | battery-level | Battery | Number |

### Sensor (relative humidity)

Indicates the current relative humidity.

The ```sensor_relhumidity``` channel supports the ```Number``` item and is in the ```Humidity``` category. This is a read only channel so will only be updated following state changes from the device.

### Sensor (ultraviolet)

Indicates the current ultraviolet level.

The ```sensor_ultraviolet``` channel supports the ```Number``` item and is in the ```Temperature``` category. This is a read only channel so will only be updated following state changes from the device.

### Sensor (temperature)

Indicates the current temperature.

The ```sensor_temperature``` channel supports the ```Number:Temperature``` item and is in the ```Temperature``` category.

### Sensor (luminance)

Indicates the current light reading.

The ```sensor_luminance``` channel supports the ```Number``` item. This is a read only channel so will only be updated following state changes from the device.

### Motion Alarm

Indicates if a motion alarm is triggered.

The ```alarm_motion``` channel supports the ```Switch``` item and is in the ```Door``` category. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the ```Switch``` item type -:

| Value | Label     |
|-------|-----------|
| OFF | OK |
| ON | Alarm |

### Tamper Alarm

Indicates if the tamper alarm is triggered.

The ```alarm_tamper``` channel supports the ```Switch``` item. This is a read only channel so will only be updated following state changes from the device.

The following state translation is provided for this channel to the ```Switch``` item type -:

| Value | Label     |
|-------|-----------|
| OFF | OK |
| ON | Alarm |

### Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The ```battery-level``` channel supports the ```Number``` item and is in the ```Battery``` category.



## Device Configuration

The following table provides a summary of the 31 configuration parameters available in the ZW100.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 2 | Stay Awake in Battery Mode			 | Stay awake for 10 minutes at power on |
| 3 | Motion Sensor reset timeout | Motion Sensor reset timeout |
| 4 | Motion sensor sensitivity | Sensitivity level of PIR sensor (1=minimum, 5=maximum) |
| 5 | Motion Sensor Triggered Command |  |
| 9 | Report the current power mode | Report the current power mode and the product state of battery power mode |
| 39 | Low Battery Report | Report Low Battery if below this value |
| 40 | Selective Reporting | Select to report on thresholds |
| 41 | Temperature Threshold | Temperature change threshold |
| 41 | Temperature Threshold Unit | Sets the unit of the threshold |
| 41 | Temperature Threshold | Threshold change in temperature to induce an automatic report. |
| 42 | Humidity Threshold | Humidity percent change threshold |
| 43 | Luminance Threshold | Luminance change threshold |
| 44 | Battery Threshold | Battery level threshold |
| 45 | Ultraviolet Threshold | Ultraviolet change threshold |
| 46 | Send Alarm Report if low temperature | Send an alarm report if temperature is less than -15 °C |
| 100 | Set parameters 101-103 to default.			 | Reset 101-103 to defaults |
| 101 | Group 1 Periodic Reports | Periodic reports to send to Group 1 |
| 102 | Group 2 Periodic Reports			 | Periodic reports to send to Group 2 |
| 103 | Group 3 Periodic Reports			 | Periodic reports to send to Group 3 |
| 110 | Set parameters 111-113 to default.			 | Set parameters 111-113 to default. |
| 111 | Group 1 Report Interval | How often to update Group 1 |
| 112 | Group 2 Report Interval | Group 2 Report Interval |
| 113 | Group 3 Report Interval | Group 3 Report Interval |
| 201 | Temperature Calibration | Temperature calibration in 0.1 deg steps |
| 201 | Temperature Calibration Unit |  |
| 201 | Temperature Calibration Value | Calibration value containing one decimal point |
| 202 | Humidity Sensor Calibration | Humidity Sensor Calibration |
| 203 | Luminance Sensor Calibration | Luminance Sensor Calibration |
| 204 | Ultraviolet Sensor Calibration | Ultraviolet Sensor Calibration |
| 252 | Disable/Enable Configuration Lock | Disable/Enable Configuration Lock (0=Disable, 1=Enable) |
| 255 | Reset to default factory settings |  |
|  | Wakeup Interval | Sets the interval at which the device will accept commands from the controller |
|  | Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |

### Parameter 2: Stay Awake in Battery Mode			

Stay awake for 10 minutes at power on
Enable/Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.  
1. Value = 0, disable.  
2. Value =others, enable.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_2_1``` and is of type ```INTEGER```.


### Parameter 3: Motion Sensor reset timeout

Motion Sensor reset timeout
  1. The default PIR time is 4 minutes. The Multisensor will send BASIC SET CC (0x00) to the associated nodes if no motion is triggered again in 4 minutes.
  2. Range: 10~3600.

**Note**:

  1. The time unit is second if the value range is in 10 to 255.
  2. If the value range is in 256 to 3600, the time unit will be minute and its value should follow the below rules:  
    a), Interval time =Value/60, if the interval time can be divided by 60 and without remainder.  
    b), Interval time= (Value/60) +1, if the interval time can be divided by 60 and has remainder.
  3. Other values will be ignored.
Values in the range 10 to 3600 may be set.

The manufacturer defined default value is ```240```.

This parameter has the configuration ID ```config_3_2``` and is of type ```INTEGER```.


### Parameter 4: Motion sensor sensitivity

Sensitivity level of PIR sensor (1=minimum, 5=maximum)

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable, sensitivity level 1 (minimum) |
| 2 | Enable, sensitivity level 2 |
| 3 | Enable, sensitivity level 3 |
| 4 | Enable, sensitivity level 4 |
| 5 | Enable, sensitivity level 5 (maximum) |

The manufacturer defined default value is ```5``` (Enable, sensitivity level 5 (maximum)).

This parameter has the configuration ID ```config_4_1``` and is of type ```INTEGER```.


### Parameter 5: Motion Sensor Triggered Command



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 1 | Send Basic Set CC |
| 2 | Send Sensor Binary Report CC |

The manufacturer defined default value is ```1``` (Send Basic Set CC).

This parameter has the configuration ID ```config_5_1``` and is of type ```INTEGER```.


### Parameter 9: Report the current power mode

Report the current power mode and the product state of battery power mode
Value1 (MSB): 0x00=USB power mode, 0x01=Battery power mode

Value2 (LSB): 0x00=keep sleep state for Battery power mode, 0x01=keep awake for 10 minutes for battery power mode

NOTE: this parameter cannot be used as Get/Set usage
Values in the range 0 to 1 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_9_2``` and is of type ```INTEGER```.
This is a read only parameter.


### Parameter 39: Low Battery Report

Report Low Battery if below this value
Configure low battery value.  
Value=10 to 50.(10% to 50%)
Values in the range 10 to 50 may be set.

The manufacturer defined default value is ```20```.

This parameter has the configuration ID ```config_39_1``` and is of type ```INTEGER```.


### Parameter 40: Selective Reporting

Select to report on thresholds
Enable/disable the selective reporting only when measurements reach a certain threshold or percentage set in 41-44 below. This is used to reduce network traffic. (0 == disable, 1 == enable)

Note: If USB Power, the Sensor will check threshold every 10 seconds. If battery power, the Sensor will check the threshold when it is waken up.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_40_1``` and is of type ```INTEGER```.


### Parameter 41: Temperature Threshold

Temperature change threshold
Threshold change in temperature to induce an automatic report.  
**Note**:

  1. The unit is Fahrenheit for US version, Celsius for EU/AU version.
  2. High byte is the threshold value. Low byte is the unit (0x01=Celsius, 0x02=Fahrenheit).
  3. The threshold value (high byte) contains one decimal point. E.g. if the value is set to 20 (0x1401), the threshold value =2.0°C (EU/AU version) or if the value is set to 20 (0x1402), the threshold value=2.0 °F (US version). When the current temperature gap is more then 2.0, which will induce a temperature report to be sent out.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode.
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```20```.

This parameter has the configuration ID ```config_41_3``` and is of type ```INTEGER```.


### Parameter 41: Temperature Threshold Unit

Sets the unit of the threshold

The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 1 | Celsius |
| 2 | Fahrenheit |

The manufacturer defined default value is ```1``` (Celsius).

This parameter has the configuration ID ```config_41_3_0000000F``` and is of type ```INTEGER```.


### Parameter 41: Temperature Threshold

Threshold change in temperature to induce an automatic report.

Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_41_3_00FFFF00``` and is of type ```INTEGER```.


### Parameter 42: Humidity Threshold

Humidity percent change threshold
Threshold change in humidity to induce an automatic report.  
Note:  
1. The unit is %.  
2. The default value is 10, which means that if the current humidity gap is  
more than 10%, it will send out a humidity report.
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```10```.

This parameter has the configuration ID ```config_42_1``` and is of type ```INTEGER```.


### Parameter 43: Luminance Threshold

Luminance change threshold
Threshold change in luminance to induce an automatic report.
Values in the range 0 to 1000 may be set.

The manufacturer defined default value is ```100```.

This parameter has the configuration ID ```config_43_2``` and is of type ```INTEGER```.


### Parameter 44: Battery Threshold

Battery level threshold
Threshold change in battery level to induce an automatic report.

Note:  
1. The unit is %.  
2. The default value is 10, which means that if the current battery level gap is  
more than 10%, it will send out a battery report.
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```10```.

This parameter has the configuration ID ```config_44_1``` and is of type ```INTEGER```.


### Parameter 45: Ultraviolet Threshold

Ultraviolet change threshold
Threshold change in ultraviolet to induce an automatic report.
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```2```.

This parameter has the configuration ID ```config_45_1``` and is of type ```INTEGER```.


### Parameter 46: Send Alarm Report if low temperature

Send an alarm report if temperature is less than -15 °C
Enable/Disable to send the alarm report of low temperature (<-15°C)

Value=0, disable

Value=1, enable (The MultiSensor will send a report of Multi Level Temperature CC to controller if the current temperature is less then -15°C).

Note: The battery activity will reduced at low temperatures (-15 degrees Celsius and below), wich will lead to the product may not work normally. It is recommended to use USB power at low temperatures.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_46_1``` and is of type ```INTEGER```.


### Parameter 100: Set parameters 101-103 to default.			

Reset 101-103 to defaults
Set 101-103 to default.
Values in the range 0 to 1 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_100_1_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 101: Group 1 Periodic Reports

Periodic reports to send to Group 1
This value is a combination number made up of the sum of the values for the individual sensors and battery. The sensors have these values:

  * Battery=1
  * Ultraviolet=16
  * Temperature=32
  * Humidity=64
  * Light=128

1+16+32+64+128 = 241 and is the default value
Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```241```.

This parameter has the configuration ID ```config_101_4``` and is of type ```INTEGER```.


### Parameter 102: Group 2 Periodic Reports			

Periodic reports to send to Group 2
This value is a combination number made up of the sum of the values for the individual sensors and battery. The sensors have these values:

  * Battery=1
  * Ultraviolet=16
  * Temperature=32
  * Humidity=64
  * Light=128
Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_102_4``` and is of type ```INTEGER```.


### Parameter 103: Group 3 Periodic Reports			

Periodic reports to send to Group 3
This value is a combination number made up of the sum of the values for the individual sensors and battery. The sensors have these values:

  * Battery=1
  * Ultraviolet=16
  * Temperature=32
  * Humidity=64
  * Light=128
Values in the range 0 to 65535 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_103_4``` and is of type ```INTEGER```.


### Parameter 110: Set parameters 111-113 to default.			

Set parameters 111-113 to default.
Set parameters 111-113 to default.   
Values in the range 0 to 1 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_110_1_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 111: Group 1 Report Interval

How often to update Group 1
The interval time of sending reports in Report group 1 (Valid values 0x05-0x28DE80).

  1. The unit of interval time is second if USB power.
  2. If battery power, the minimum interval time is 60 minutes by default, for example, if the value is set to be more than 5 and less than 3600, the interval time is 60 minutes, if the value is set to be more than 3600 and less than 7200, the interval time is 120 minutes. You can also change the minimum interval time to 4 minutes via setting the interval value(3 bytes) to 240 in Wake Up Interval Set CC.
Values in the range 5 to 2678400 may be set.

The manufacturer defined default value is ```3600```.

This parameter has the configuration ID ```config_111_4``` and is of type ```INTEGER```.


### Parameter 112: Group 2 Report Interval

Group 2 Report Interval
The interval time of sending reports in Report group 2 (Valid values 0x05-  
0x28DE80).  
Note:  
1. The unit of interval time is second if USB power.  
2. If battery power, the minimum interval time is 60 minutes by default, for  
example, if the value is set to be more than 5 and less than 3600, the interval  
time is 60 minutes, if the value is set to be more than 3600 and less than 7200,  
the interval time is 120 minutes. You can also change the minimum interval time  
to 4 minutes via setting the interval value(3 bytes) to 240 in Wake Up Interval Set  
CC.
Values in the range 5 to 2678400 may be set.

The manufacturer defined default value is ```3600```.

This parameter has the configuration ID ```config_112_4``` and is of type ```INTEGER```.


### Parameter 113: Group 3 Report Interval

Group 3 Report Interval
The interval time of sending reports in Report group 3

  1. The unit of interval time is second if USB power.
  2. If battery power, the minimum interval time is 60 minutes by default, for example, if the value is set to be more than 5 and less than 3600, the interval time is 60 minutes, if the value is set to be more than 3600 and less than 7200, the interval time is 120 minutes. You can also change the minimum interval time to 4 minutes via setting the interval value(3 bytes) to 240 in Wake Up Interval Set CC.
Values in the range 5 to 2678400 may be set.

The manufacturer defined default value is ```3600```.

This parameter has the configuration ID ```config_113_4``` and is of type ```INTEGER```.


### Parameter 201: Temperature Calibration

Temperature calibration in 0.1 deg steps
Temperature calibration (the available value range is [-128,127] or [-12.8°C ,12.7 °C ] ).  
**Note**:

  1. High byte is the calibration value. Low byte is the unit (0x01=Celsius, 0x02=Fahrenheit).
  2. The calibration value (high byte) contains one decimal point. E.g. if the value is set to 20 (0x1401), the calibration value is 2.0°C (EU/AU version) or if the value is set to 20 (0x1402), the calibration value is 2.0 °F (US version)
  3. The calibration value = standard value - measure value. °C and the standard value = 23.2 °C , so the calibration value= 23.2 °C - 25.3 °C = -2.1 °C (0xEB). If the measure value =30.1 °C and the standard value = 33.2 °C , so the calibration value= 33.2 °C - 30.1 °C =3.1 °C (0x1F).This is an advanced parameter and will therefore not show in the user interface without entering advanced mode.
Values in the range -128 to 127 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_201_2``` and is of type ```INTEGER```.


### Parameter 201: Temperature Calibration Unit



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 1 | Celsius |
| 2 | Fahrenheit |

The manufacturer defined default value is ```1``` (Celsius).

This parameter has the configuration ID ```config_201_2_000000FF``` and is of type ```INTEGER```.


### Parameter 201: Temperature Calibration Value

Calibration value containing one decimal point

Values in the range -127 to 127 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_201_2_0000FF00``` and is of type ```INTEGER```.


### Parameter 202: Humidity Sensor Calibration

Humidity Sensor Calibration
Humidity sensor calibration (the available value range is [-50, 50]).  
The calibration value = standard value - measure value.  
E.g. If measure value =80RH and the standard value = 75RH, so the calibration  
value= 75RH – 80RH= -5RH (0xFB).  
If the measure value =85RH and the standard value = 90RH, so the calibration  
value= 90RH – 85RH=5RH (0x05).
Values in the range -50 to 50 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_202_1``` and is of type ```INTEGER```.


### Parameter 203: Luminance Sensor Calibration

Luminance Sensor Calibration
Luminance sensor calibration (the available value range is [-1000, 1000]).  
The calibration value = standard value - measure value.  
E.g. If measure value =800Lux and the standard value = 750Lux, so the  
calibration value= 750 – 800= -50 (0xFFCE).  
If the measure value =850Lux and the standard value = 900Lux, so the calibration  
value= 900 – 850=50 (0x0032).
Values in the range -1000 to 1000 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_203_2``` and is of type ```INTEGER```.


### Parameter 204: Ultraviolet Sensor Calibration

Ultraviolet Sensor Calibration
Ultraviolet sensor calibration (the available value range is [-10, 10]).  
The calibration value = standard value - measure value.  
E.g. If measure value =9 and the standard value = 8, so the calibration value= 8 –  
9= -1 (0xFE).  
If the measure value =7 and the standard value = 9, so the calibration value= 9 –  
7=2 (0x02).
Values in the range -10 to 10 may be set.

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_204_1``` and is of type ```INTEGER```.


### Parameter 252: Disable/Enable Configuration Lock

Disable/Enable Configuration Lock (0=Disable, 1=Enable)
Disable/Enable Configuration Lock (0=Disable, 1=Enable)
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_252_1``` and is of type ```INTEGER```.


### Parameter 255: Reset to default factory settings


This is an advanced parameter and will therefore not show in the user interface without entering advanced mode.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 1 | Resets all configuration parameters to defaults |
| 1431655765 | Reset to default factory settings and be excluded |

The manufacturer defined default value is ```0```.

This parameter has the configuration ID ```config_255_4_wo``` and is of type ```INTEGER```.
This is a write only parameter.

### Wakeup Interval

The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications. 

This setting is defined in *seconds*. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.

Note that this setting does not affect the devices ability to send sensor data, or notification events.

This parameter has the configuration ID ```wakeup_interval``` and is of type ```INTEGER```.

### Wakeup Node

When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address.
In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.

This parameter has the configuration ID ```wakeup_node``` and is of type ```INTEGER```.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The ZW100 supports 3 association groups.

### Group 1: Group 1


Association group 1 supports 5 nodes.

### Group 2: Group 2


Association group 2 supports 5 nodes.

### Group 3: Group 3


Association group 3 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_BINARY_V1| Linked to BASIC|
| COMMAND_CLASS_SENSOR_MULTILEVEL_V5| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_ALARM_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_BATTERY_V1| |
| COMMAND_CLASS_WAKE_UP_V2| |
| COMMAND_CLASS_ASSOCIATION_V1| |
| COMMAND_CLASS_VERSION_V1| |

### Documentation Links

* [Engineering Manual](https://www.cd-jackson.com/zwave_device_uploads/355/9-Multisensor-6-V1-07.pdf)
* [Engineering Specification and Advanced Functions Multisensor 6 V1.07 Rev.2](https://www.cd-jackson.com/zwave_device_uploads/355/Engineering-Spec---Aeon-Labs-MultiSensor-6-V1-07.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/355).