--- layout: documentation title: ZW090 - ZWave --- {% include base.html %} # ZW090 Z‐Stick Gen5 USB Controller This describes the Z-Wave device *ZW090*, manufactured by *[AEON Labs](http://aeotec.com/)* with the thing type UID of ```aeon_zw090_00_000```. The device is in the category of *Remote Control*, defining Any portable or hand-held device that controls the status of something, e.g. remote control, keyfob etc.. ![ZW090 product image](https://www.cd-jackson.com/zwave_device_uploads/265/265_default.png) ## Overview Aeon Labs Z‐Stick Gen5 is a self‐powered Z‐Wave USB adapter with remote network creation capabilities (independent from external power and host microprocessor).  By being able to remotely include/remove Z‐ Wave devices, this greatly simplifies Z‐Wave network installation.  When connected to a host controller (via USB), it enables the host controller to take part in the Z‐Wave Network. It can be included and operated in any Z‐wave network with other Z‐wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.  ### Inclusion Information Push the include button.  Controller will blink slowly.  It is in include mode.  Press again to cancel. ### Exclusion Information 1. Unplug the Z‐Stick from the USB connector. Then press and hold the Action Button for approximately 2 seconds. (The orange LED will blinking fast.) 2. To remove a Z‐Wave device from the network, simply go to the device with the Z‐Stick and press the Action Button on the device you wish to remove. (The LED on the Z‐Stick will become blue and Immediately stay solid for 2 seconds to indicate successful removal from the network.) 3.   The orange LED will then return to blinking fast, indicating readiness for further device exclusions. Repeat step 1 for each device as you wish to exclude ## Channels The following table summarises the channels available for the ZW090 -: | Channel | Channel Id | Category | Item Type | |---------|------------|----------|-----------| ## Device Configuration The following table provides a summary of the 5 configuration parameters available in the ZW090. Detailed information on each parameter can be found in the sections below. | Param | Name | Description | |-------|-------|-------------| | 81 | Enable/disable the LED indicator | This parameter is used to enable/disable the LED indicator. | | 220 | RF power level | RF power level | | 242 | Security network enabled | Security network enabled | | 243 | Security Network Key | Security Network Key | | 252 | Lock Configuration | Configuration lock. 1=enable, 0=disable | ### Parameter 81: Enable/disable the LED indicator This parameter is used to enable/disable the LED indicator. When the USB power supply, the LED indicator light configuration (0 =disable, 1 = enable) The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | Disable | | 1 | Enable | The manufacturer defined default value is ```1``` (Enable). This parameter has the configuration ID ```config_81_1``` and is of type ```INTEGER```. ### Parameter 220: RF power level RF power level Configuration of the RF power level 1~10, other= ignore. A total of 10 levels, level 1 as the weak output power, and so on, 10 for most output power level. Values in the range 1 to 10 may be set. The manufacturer defined default value is ```10```. This parameter has the configuration ID ```config_220_1``` and is of type ```INTEGER```. ### Parameter 242: Security network enabled Security network enabled Security network enabled (0 =disable, 1 = enable) The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | disable | | 1 | enable | The manufacturer defined default value is ```0``` (disable). This parameter has the configuration ID ```config_242_1``` and is of type ```INTEGER```. ### Parameter 243: Security Network Key Security Network Key Values in the range 0 to 0 may be set. The manufacturer defined default value is ```0```. This parameter has the configuration ID ```config_243_16``` and is of type ```INTEGER```. ### Parameter 252: Lock Configuration Configuration lock. 1=enable, 0=disable Enable/disable Lock Configuration (0 =disable, 1= enable, other= ignore) The following option values may be configured -: | Value | Description | |--------|-------------| | 0 | disable | | 1 | enable | The manufacturer defined default value is ```0``` (disable). This parameter has the configuration ID ```config_252_1``` and is of type ```INTEGER```. ## Association Groups Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic. The ZW090 supports 1 association group. ### Group 1: Z-Stick Gen5 (ZW090-A) Z-Wave Plus Lifeline Association group 1 supports 5 nodes. ## Technical Information ### Endpoints #### Endpoint 0 | Command Class | Comment | |---------------|---------| | COMMAND_CLASS_NO_OPERATION_V1| | | COMMAND_CLASS_BASIC_V1| | | COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1| | | COMMAND_CLASS_CONFIGURATION_V1| | ### Documentation Links * [Engineering Manual](https://www.cd-jackson.com/zwave_device_uploads/265/1-Z-Stick-Gen5.pdf) * [Z-Wave Protocol Implementation Conformance Statement - Z-Stick Gen5](https://www.cd-jackson.com/zwave_device_uploads/265/Z-Wave-Protocol-Implementation-Conformance-Statement.pdf) --- Did you spot an error in the above definition or want to improve the content? You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/265).