---
layout: documentation
title: DSB09 - ZWave
---

{% include base.html %}

# DSB09 Home Energy Meter
This describes the Z-Wave device *DSB09*, manufactured by *[AEON Labs](http://aeotec.com/)* with the thing type UID of ```aeon_dsb09_00_000```.

The device is in the category of *Sensor*, defining Device used to measure something.

![DSB09 product image](https://www.cd-jackson.com/zwave_device_uploads/84/84_default.jpg)


The DSB09 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers.  This device is also able to participate in the routing of data between other devices in the mesh network.

## Overview

Your Home Energy Meter can be reset to default factory settings with ease.

  1. Press and hold the Action Button for 10 seconds.
  2. If successful, the LED on the HEM should begin to blink slowly.

### Inclusion Information

The electrical installation of your Home Energy Meter (HEM) is now complete. You  must now wirelessly link it to your Z-Wave network.

  1. Put your primary Z-Wave controller, usually a gateway or hub, into inclusion mode. If  you are not sure how to do this, please refer to your controller’s user manual.
  2. Press the Action Button on your HEM. If it has been successfully linked to your  network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to blink.

### Exclusion Information

Your Home Energy Meter (HEM) can be removed from your Z-Wave network at  any time. You'll need to use your Z-Wave network’s primary to do this.

  1. Put your main controller into its device removal mode. If you are unsure how to do  this, please refer to your controller’s user manual.
  2. Press the Action Button on your HEM. If it has been successfully removed from your  network, its LED will blink. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.

### General Usage Information

NOTE: If a report is included in more then one Report Group, it will only be sent in the Report Group with the most recently updated configuration parameter.

## Channels

The following table summarises the channels available for the DSB09 -:

| Channel | Channel Id | Category | Item Type |
|---------|------------|----------|-----------|
| Sensor (power) | sensor_power | Energy | Number | 
| Electric meter (kWh) | meter_kwh | Energy | Number | 
| Electric meter (watts) | meter_watts | Energy | Number | 
| Reset Meter | meter_reset | Energy | Switch | 
| Battery Level | battery-level | Battery | Number |
| Sensor (power) 1 | sensor_power1 | Energy | Number | 
| Electric meter (kWh) 1 | meter_kwh1 | Energy | Number | 
| Electric meter (watts) 1 | meter_watts1 | Energy | Number | 
| Sensor (power) 2 | sensor_power2 | Energy | Number | 
| Electric meter (kWh) 2 | meter_kwh2 | Energy | Number | 
| Electric meter (watts) 2 | meter_watts2 | Energy | Number | 
| Sensor (power) 3 | sensor_power3 | Energy | Number | 
| Electric meter (kWh) 3 | meter_kwh3 | Energy | Number | 
| Electric meter (watts) 3 | meter_watts3 | Energy | Number | 

### Sensor (power)

Indicates the energy consumption (kWh).

The ```sensor_power``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (kWh)

Indicates the energy consumption (kWh).

The ```meter_kwh``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (watts)

Indicates the instantaneous power consumption.

The ```meter_watts``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Reset Meter

Reset the meter.

The ```meter_reset``` channel supports the ```Switch``` item and is in the ```Energy``` category.

### Battery Level

Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.

The ```battery-level``` channel supports the ```Number``` item and is in the ```Battery``` category.

### Sensor (power) 1

Indicates the energy consumption (kWh).

The ```sensor_power1``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (kWh) 1

Indicates the energy consumption (kWh).

The ```meter_kwh1``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (watts) 1

Indicates the instantaneous power consumption.

The ```meter_watts1``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Sensor (power) 2

Indicates the energy consumption (kWh).

The ```sensor_power2``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (kWh) 2

Indicates the energy consumption (kWh).

The ```meter_kwh2``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (watts) 2

Indicates the instantaneous power consumption.

The ```meter_watts2``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Sensor (power) 3

Indicates the energy consumption (kWh).

The ```sensor_power3``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (kWh) 3

Indicates the energy consumption (kWh).

The ```meter_kwh3``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.

### Electric meter (watts) 3

Indicates the instantaneous power consumption.

The ```meter_watts3``` channel supports the ```Number``` item and is in the ```Energy``` category. This is a read only channel so will only be updated following state changes from the device.



## Device Configuration

The following table provides a summary of the 49 configuration parameters available in the DSB09.
Detailed information on each parameter can be found in the sections below.

| Param | Name  | Description |
|-------|-------|-------------|
| 1 | Voltage | Voltage to calculate wattage from amperage. |
| 3 | Selective Reporting: Whole HEM |  |
| 3 | Selective Reporting: Clamp 1 |  |
| 3 | Selective Reporting: Clamp 2 |  |
| 3 | Selective Reporting: Clamp 3 |  |
| 4 | Current Threshold - Whole HEM | Threshold change in wattage to induce an automatic report (Whole HEM). |
| 5 | Current Threshold - Clamp 1 | Threshold change in wattage to induce an automatic report (Clamp 1) |
| 6 | Current Threshold - Clamp 2 | Threshold change in wattage to induce an automatic report (Clamp 2) |
| 7 | Current Threshold - Clamp 3 | Threshold change in wattage to induce an automatic report (Clamp 3) |
| 8 | Percent Change - Whole HEM | Percentage change in wattage to induce an automatic report (Whole HEM) |
| 9 | Percent Change - Clamp 1 | Percentage change in wattage to induce an automatic report (Clamp 1) |
| 10 | Percent Change - Clamp 2 | Percentage change in wattage to induce an automatic report (Clamp 2) |
| 11 | Percent Change - Clamp 3 | Percentage change in wattage to induce an automatic report (Clamp 3) |
| 100 | Set parameters 101-103 to default values |  |
| 101 | Report Group 1: Battery Report |  |
| 101 | Report Group 1: MultiSensor Report for Watt (whole HEM) |  |
| 101 | Report Group 1: Meter Report for Watt (whole device) |  |
| 101 | Report Group 1: Meter Report for kWh (whole HEM) |  |
| 101 | Report Group 1: Meter Report for Watt (clamp 1) |  |
| 101 | Report Group 1: Meter Report for Watt (clamp 2) |  |
| 101 | Report Group 1: Meter Report for Watt (clamp 3) |  |
| 101 | Report Group 1: Meter Report for kWh (clamp 1) |  |
| 101 | Report Group 1: Meter Report for kWh (clamp 2) |  |
| 101 | Report Group 1: Meter Report for kWh (clamp 3) |  |
| 102 | Report Group 2: Battery Report |  |
| 102 | Report Group 2: MultiSensor Report for Watt (whole HEM) |  |
| 102 | Report Group 2: Meter Report for Watt (whole device) |  |
| 102 | Report Group 2: Meter Report for kWh (whole HEM) |  |
| 102 | Report Group 2: Meter Report for Watt (clamp 1) |  |
| 102 | Report Group 2: Meter Report for Watt (clamp 2) |  |
| 102 | Report Group 2: Meter Report for Watt (clamp 3) |  |
| 102 | Report Group 2: Meter Report for kWh (clamp 1) |  |
| 102 | Report Group 2: Meter Report for kWh (clamp 2) |  |
| 102 | Report Group 2: Meter Report for kWh (clamp 3) |  |
| 103 | Report Group 3: Battery Report |  |
| 103 | Report Group 3: MultiSensor Report for Watt (whole HEM) |  |
| 103 | Report Group 3: Meter Report for Watt (whole device) |  |
| 103 | Report Group 3: Meter Report for kWh (whole HEM) |  |
| 103 | Report Group 3: Meter Report for Watt (clamp 1) |  |
| 103 | Report Group 3: Meter Report for Watt (clamp 2) |  |
| 103 | Report Group 3: Meter Report for Watt (clamp 3) |  |
| 103 | Report Group 3: Meter Report for kWh (clamp 1) |  |
| 103 | Report Group 3: Meter Report for kWh (clamp 2) |  |
| 103 | Report Group 3: Meter Report for kWh (clamp 3) |  |
| 110 | Set parameters 111-113 to default values |  |
| 111 | Interval to send Report Group 1 |  |
| 112 | Interval to send Report Group 2 |  |
| 113 | Interval to send Report Group 3 |  |
| 255 | Reset to Factory | Reset all settings to factory defaults |

### Parameter 1: Voltage

Voltage to calculate wattage from amperage.

Values in the range 0 to 32000 may be set.

The manufacturer defined default value is ```240```.

This parameter has the configuration ID ```config_1_2``` and is of type ```INTEGER```.


### Parameter 3: Selective Reporting: Whole HEM



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_3_1_00000001``` and is of type ```INTEGER```.


### Parameter 3: Selective Reporting: Clamp 1



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_3_1_00000002``` and is of type ```INTEGER```.


### Parameter 3: Selective Reporting: Clamp 2



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_3_1_00000004``` and is of type ```INTEGER```.


### Parameter 3: Selective Reporting: Clamp 3



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_3_1_00000008``` and is of type ```INTEGER```.


### Parameter 4: Current Threshold - Whole HEM

Threshold change in wattage to induce an automatic report (Whole HEM).
Valid values: 0-60,000
Values in the range 0 to 60000 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_4_2``` and is of type ```INTEGER```.


### Parameter 5: Current Threshold - Clamp 1

Threshold change in wattage to induce an automatic report (Clamp 1)
Valid values: 0-60,000
Values in the range 0 to 60000 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_5_2``` and is of type ```INTEGER```.


### Parameter 6: Current Threshold - Clamp 2

Threshold change in wattage to induce an automatic report (Clamp 2)
Valid values: 0-60,000
Values in the range 0 to 60000 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_6_2``` and is of type ```INTEGER```.


### Parameter 7: Current Threshold - Clamp 3

Threshold change in wattage to induce an automatic report (Clamp 3)
Valid values: 0-60,000
Values in the range 0 to 60000 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_7_2``` and is of type ```INTEGER```.


### Parameter 8: Percent Change - Whole HEM

Percentage change in wattage to induce an automatic report (Whole HEM)
Valid values: 0-100
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_8_1``` and is of type ```INTEGER```.


### Parameter 9: Percent Change - Clamp 1

Percentage change in wattage to induce an automatic report (Clamp 1)
Valid values: 0-100
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_9_1``` and is of type ```INTEGER```.


### Parameter 10: Percent Change - Clamp 2

Percentage change in wattage to induce an automatic report (Clamp 2)
Valid values: 0-100
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_10_1``` and is of type ```INTEGER```.


### Parameter 11: Percent Change - Clamp 3

Percentage change in wattage to induce an automatic report (Clamp 3)
Valid values: 0-100
Values in the range 0 to 100 may be set.

The manufacturer defined default value is ```50```.

This parameter has the configuration ID ```config_11_1``` and is of type ```INTEGER```.


### Parameter 100: Set parameters 101-103 to default values



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | No change |
| 1 | Reset |

The manufacturer defined default value is ```0``` (No change).

This parameter has the configuration ID ```config_100_4_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 101: Report Group 1: Battery Report



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000001``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: MultiSensor Report for Watt (whole HEM)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000002``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for Watt (whole device)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000004``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for kWh (whole HEM)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000008``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for Watt (clamp 1)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000100``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for Watt (clamp 2)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000200``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for Watt (clamp 3)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000400``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for kWh (clamp 1)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00000800``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for kWh (clamp 2)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00001000``` and is of type ```INTEGER```.


### Parameter 101: Report Group 1: Meter Report for kWh (clamp 3)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_101_4_00002000``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Battery Report



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000001``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: MultiSensor Report for Watt (whole HEM)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000002``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for Watt (whole device)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000004``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for kWh (whole HEM)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000008``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for Watt (clamp 1)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000100``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for Watt (clamp 2)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000200``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for Watt (clamp 3)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000400``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for kWh (clamp 1)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00000800``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for kWh (clamp 2)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00001000``` and is of type ```INTEGER```.


### Parameter 102: Report Group 2: Meter Report for kWh (clamp 3)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_102_4_00002000``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Battery Report



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000001``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: MultiSensor Report for Watt (whole HEM)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000002``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for Watt (whole device)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000004``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for kWh (whole HEM)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000008``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for Watt (clamp 1)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000100``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for Watt (clamp 2)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000200``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for Watt (clamp 3)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000400``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for kWh (clamp 1)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00000800``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for kWh (clamp 2)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00001000``` and is of type ```INTEGER```.


### Parameter 103: Report Group 3: Meter Report for kWh (clamp 3)



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Disable |
| 1 | Enable |

The manufacturer defined default value is ```0``` (Disable).

This parameter has the configuration ID ```config_103_4_00002000``` and is of type ```INTEGER```.


### Parameter 110: Set parameters 111-113 to default values



The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | No change |
| 1 | Reset |

The manufacturer defined default value is ```0``` (No change).

This parameter has the configuration ID ```config_110_4_wo``` and is of type ```INTEGER```.
This is a write only parameter.


### Parameter 111: Interval to send Report Group 1



Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is ```720```.

This parameter has the configuration ID ```config_111_4``` and is of type ```INTEGER```.


### Parameter 112: Interval to send Report Group 2



Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is ```720```.

This parameter has the configuration ID ```config_112_4``` and is of type ```INTEGER```.


### Parameter 113: Interval to send Report Group 3



Values in the range 1 to 2678400 may be set.

The manufacturer defined default value is ```720```.

This parameter has the configuration ID ```config_113_4``` and is of type ```INTEGER```.


### Parameter 255: Reset to Factory

Reset all settings to factory defaults
Reset all settings in unit to factory settings.  If you're getting crazy voltage readings in a unit after upgrading firmware, use this then reconfigure the unit.This is an advanced parameter and will therefore not show in the user interface without entering advanced mode.
The following option values may be configured -:

| Value  | Description |
|--------|-------------|
| 0 | Do nothing |
| 1 | Reset to factory defaults |

The manufacturer defined default value is ```0``` (Do nothing).

This parameter has the configuration ID ```config_255_4_wo``` and is of type ```INTEGER```.
This is a write only parameter.


## Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The DSB09 supports 3 association groups.

### Group 1: Report group 1


Association group 1 supports 5 nodes.

### Group 2: Report group 2


Association group 2 supports 5 nodes.

### Group 3: Report group 3


Association group 3 supports 5 nodes.

## Technical Information

### Endpoints

#### Endpoint 0

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_NO_OPERATION_V1| |
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2| |
| COMMAND_CLASS_METER_V2| |
| COMMAND_CLASS_MULTI_CHANNEL_V2| |
| COMMAND_CLASS_CONFIGURATION_V1| |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1| |
| COMMAND_CLASS_BATTERY_V1| |
| COMMAND_CLASS_ASSOCIATION_V1| |
| COMMAND_CLASS_VERSION_V1| |
#### Endpoint 1

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2| |
| COMMAND_CLASS_METER_V2| |
#### Endpoint 2

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2| |
| COMMAND_CLASS_METER_V2| |
#### Endpoint 3

| Command Class | Comment |
|---------------|---------|
| COMMAND_CLASS_BASIC_V1| |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2| |
| COMMAND_CLASS_METER_V2| |

### Documentation Links

* [Advanced Functions for Developers (SW Version: 3.58+)](https://www.cd-jackson.com/zwave_device_uploads/84/26-Home-Energy-Meter-G1.pdf)

---

Did you spot an error in the above definition or want to improve the content?
You can [contribute to the database here](http://www.cd-jackson.com/index.php/zwave/zwave-device-database/zwave-device-list/devicesummary/84).