Overview:
The Ecolink Audio detector sensor listens to existing smoke or CO detectors in the home and sends signal to your Z-Wave network. In most homes, with hardwired interconnected smoke detectors, only one sensor is needed for whole home coverage.
This device implements Z-Wave Plus functionality, Network Wide Inclusion, and Explorer frames. This device is asleep most of the time but can respond to queries on a Wake Up Notification; however for test purposes, the device will stay awake while tampered for testing Z-Wave Plus command class functionality.
LED Status:
The FireFighter sensor is equipped with a multi-color LED. The state of the LED will change based on the state of the device.
| Insert Battery | One (or two, if in CO mode) RED blink, then one GREEN blink |
| Device not included | Green light breathing (slow blink) |
| Learn button pressed | Solid Yellow (red+green) while in learn mode |
| Sound detected | Flash YELLOW for the duration of the sound |
| Fire Alarm Detected | Solid RED for 3 seconds, then blink red while tone detected |
| Case Opened | Red/Green breathing until case closed (while added to a network) |
CO Alarm Detection:
In addition to smoke alarm detection, the FireFighter sensor can detect the presence of a carbon monoxide alarm. By default, the sensor is not guaranteed to detect a CO alarm. The device can be configured to more reliably detect a CO alarm in exchange for a reduced battery life. This mode can be changed by holding down the tamper switch and the learn button for 10 seconds. The device should then be reset (remove battery and replace) in order to determine the current device setting.
RED + GREEN = Device will not reliably detect CO, but standard battery life
RED + RED + GREEN = Device will more reliably detect CO, but with reduced battery life
Factory Default:
The FireFighter sensor can be restored back to factory default settings which will remove its Z-Wave Plus node ID from the sensor (but not the controller) with the following steps. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Testing:
To test the RF transmission from the mounted position you can generate a tamper by removing the cover. This will send a signal to the controller. To test the audio detection, press and hold the smoke detector's test button. Ensure the FireFighter cover is on and that you wear hearing protection.
Open the FireFighter case and press the learn button on the device for one second. If the LED starts blinking continually, the sensor has not been added and you need to repeat the process after putting the controller into inclusion mode again.
Open the FireFighter case and press the learn button on the device for one second. If successfully removed from the Z-Wave Plus network, the device's Green LED should blink slowly and continuously.
The sensor will wake up every so often to send a Wake-Up Notification to allow the life line master node controller that the sensor is now available for any queued messages that the controller may have for the sensor. The time between Wake-Up Notifications can be configured with the Wake-Up Notification command class to be between 1 hour and 1 week with interval steps of 200 seconds. The sensor will also send a wakeup notification whenever the case is closed.
- ]]>Enables the sensor to detect smoke alarm signals from a smoke detector or alarm signals from a smoke alarm and carbon monoxide alarm combo device. Allowed parameter values:
0xA5 = Smoke alarm detection only
0xFF = Smoke and carbon monoxide alarm detection
- ]]>Will receive unsolicited messages relating to Fire notifications, CO notifications, case tampering notifications, low-battery notifications, and temperature notifications.
- ]]>HS-WX300 is a Z-Wave
Touch switch is an in-wall switchgear based on Z-Wave wireless radio frequency technology for intelligent control. This product can be added to the gateway or PC controller supporting Z-Wave Plus, remotely controlled through the APP interface, or manually controlled by the touch. In addition, the product also supports the scene mode, the user can configure the scene through the APP, combine various devices in the same scene, and run the scene function through the APP or manually. Press button “A” on the lock one time to include it in your system. Press button “A” on the lock one time to include it in your system. Door lock status LED blinks every 6 seconds. Factory default is ON. Lock automatically re-locks door 30 seconds after unlocking. OFF position is factory default. If this switch is turned on, it will be disabled if all codes are deleted from the lock. Internal buzzer enabled. Factory default is ON. It is recommended that the buzzer is left ON during programming. Configuration parameters 33 and 34 are used to set and get the SKU part numbers. The SKU is made up of 8 bytes. Each parameter consists of four bytes of data. Parameter 33 contains the first four most significant bytes of the SKU, while parameter 34 contains the four least significant bytes of the SKU. When setting the SKU, it must be done in two set commands, one for each parameter. The order of programming the SKU does not matter. Setting parameter 33 will program the first four bytes of the SKU. Setting parameter 34 will program the last 4 bytes of the SKU. Most printable values are accepted for the set command. When getting the SKU, it must be done in two get commands, one for each parameter. The order of getting the SKU does not matter. Getting parameter 33 will retrieve the first four bytes of the SKU. Getting parameter 34 will retrieve the last 4 bytes of the SKU Configuration parameters 33 and 34 are used to set and get the SKU part numbers. The SKU is made up of 8 bytes. Each parameter consists of four bytes of data. Parameter 33 contains the first four most significant bytes of the SKU, while parameter 34 contains the four least significant bytes of the SKU. When setting the SKU, it must be done in two set commands, one for each parameter. The order of programming the SKU does not matter. Setting parameter 33 will program the first four bytes of the SKU. Setting parameter 34 will program the last 4 bytes of the SKU. Most printable values are accepted for the set command. When getting the SKU, it must be done in two get commands, one for each parameter. The order of getting the SKU does not matter. Getting parameter 33 will retrieve the first four bytes of the SKU. Getting parameter 34 will retrieve the last 4 bytes of the SKU The configuration parameter 40 is a one-byte field, used to set the lock to its default setting, known as a factory reset command. Reading this parameter will always return a value of 0. Writing a value of 1 to this parameter will cause both the lock and Z-Wave card to reset back to their default settings and will remove itself from the network. All network information, including associations, will be cleared. Per Z-Wave Plus requirements, group 1 is assigned to the Lifeline group and can only support 1 node. Association group 2 is identified as the “Doorlock notify report” group. It allows at most 5 other nodes to be associated with the lock and will provide all Notification Reports, via the Command Class Notification, generated by the lock. Motio
Motio
This parameter defines the calibrated scale for ambient light intensity. Because the method and position that the sensor mounted and the cover of sensor will bring measurement error, user can get more real light intensity by this parameter setting. User should run the steps as blows for calibrating 1. Set this parameter value to default(Assumes the sensor has been added in a Z-Wave Network). 2. Place a digital luxmeter close to sensor and keep the same direction, monitor the light intensity value (Vm) which report to controller and record it. The same time user should record the value (Vs) of Iuxmeter. 3. The scale calibration formula: k = Vm IVS. 4. The value of k is then multiplied by 1000 and rounded to the nearest whole number. 5. Set the value getting in 5) to this parameter, calibrate finished. For example, Vm = 300, Vs = 2000, then k = 300 / 2600 = 0.11538 k=0.11538*1000=115.38=115 The parameter should be set to 115. This parameter defines the calibrated scale for ambient light intensity. Because the method and position that the sensor mounted and the cover of sensor will bring measurement error, user can get more real light intensity by this parameter setting. User should run the steps as blows for calibrating 1. Set this parameter value to default(Assumes the sensor has been added in a Z-Wave Network). 2. Place a digital luxmeter close to sensor and keep the same direction, monitor the light intensity value (Vm) which report to controller and record it. The same time user should record the value (Vs) of Iuxmeter. 3. The scale calibration formula: k = Vm IVS. 4. The value of k is then multiplied by 1000 and rounded to the nearest whole number. 5. Set the value getting in 5) to this parameter, calibrate finished. For example, Vm = 300, Vs = 2000, then k = 300 / 2600 = 0.11538 k=0.11538*1000=115.38=115 The parameter should be set to 115. 5 in 1 sensor: motion, temperature, humidity, luminance, tamper alarm Blue led will blink with 1 s interval until inclusion successful. Blue led will blink with 0.5 s interval until exclusion successful. Send NIF: Press and hold the button for 5 s until white led light is on, then release the button before led turns off. 5 in 1 sensor: motion, temperature, humidity, luminance, tamper alarm Blue led will blink with 1 s interval until inclusion successful. This device supports 2 role type: AOS(Always On Slave) and LPM(Low Power Mode). Which role type is valid decided by which power (Battery or DC Power) is supplied when included. The role type is AOS only if DC power supply first. Listening=true The role type is LPM only if battery supply first. Listening = false When device is included with AOS, it also can make a repeater role. Blue led will blink with 0.5 s interval until exclusion successful. Send NIF: Press and hold the button for 5 s until white led light is on, then release the button before led turns off. 5 in 1 sensor: motion, temperat
This parameter is configured the sensitivity that motion detect. This value is larger, the sensitivity is lower, and the distance for motion detecting is closer. Available settings: 0 ... 15. Default: 1 '1' - Enable sensor binary report when device detects a motion event. '0' - Disable sensor binary report when device detects a motion event. Default: Disable This parameter is configured the sensitivity that motion detect. This value is larger, the sensitivity is lower, and the distance for motion detecting is closer. Available settings: 0 ... 15. Default: 2 The current measuring temperature value can be add and minus a value by this setting. Temperature Offset Value = [Value] x 0.1 Degree Celsius / Fahrenheit (US). Available settings: -120 ... 120. Default: 0 5 in 1 sensor: motion, temperat
The current measuring humidity value can be add and minus a value by this setting. Humidity Offset Value = [Value] x 0.1 RH%. Available settings: -120 ... 120. Default: 0 5 in 1 sensor: motion, temperat
This configuration sets the changed value of the temperature. When the difference from the last report exceeds this setting value, the device will report current temperature value to Z-Wave Hubs. The D-Value = [Value] x 0.1 Degree Celsius / Fahrenheit (US). Available settings: 0 ... 120. Default: 10 This configuration sets the changed value of the temperature. When the difference from the last report exceeds this setting value, the device will report current temperature value to Z-Wave Hubs. The D-Value = [Value] x 0.1 Degree Celsius / Fahrenheit (US). Available settings: 0 ... 100. Default: 10 This configuration sets the changed value of the humidity. When the difference from the last report exceeds this setting value, the device will report current humidity value to Z-Wave Hubs. The D-Value = [Value] x 0.1 RH%. Available settings: 0 ... 120. Default: 20 This configuration sets the changed value of the humidity. When the difference from the last report exceeds this setting value, the device will report current humidity value to Z-Wave Hubs. The D-Value = [Value] x 0.1 RH%. Available settings: 0 ... 100. Default: 20 This configuration sets the changed value of the luminance. When the difference from the last report exceeds this setting value, the device will report current luminance value to Z-Wave Hubs. Unit: Lux. Available settings: 0 ... 120. Default: 50 5 in 1 sensor: motion, temperat
This parameter is configured the value that BASIC_SET for nodes that associated in Group 2. '100' - BASIC_SET = 0xFF (ON). '0' - BASIC_SET = 0x00 (OFF). Available settings: 0 ... 100. Default: 100 5 in 1 sensor: motion, temperat
This parameter is configured the time delay for device sending BASIC_SET = 0x00 to nodes that associated in Group 2 when device detects a motion event. [0] - Not Send BASIC_SET = 0x00 Command. [1-30000] - Time delay count. Unit: Second. Available settings: 0 ... 30000. Default: 30 5 in 1 sensor: motion, temperat
Default: 50 This parameter is configured the time delay for device sending BASIC_SET = 0x00 to nodes that associated in Group 2 when device detects a motion event. [0] - Not Send BASIC_SET = 0x00 Command. [1-30000] - Time delay count. Unit: Second. Available settings: 0 ... 30000. Default: 30 This parameter is configured the time interval for light sensor, temperature and humidity sensor measuring. This value is larger, the battery life is longer. And the sensors values changed are not obvious. 0 - All sensors are disabled. Unit: Second. Available settings: 0 - 30000. Default: 180 (on batteries) or 10 (on USB) This parameter is configured the time to clear motion event after a motion event is detected. Time to motion clear, the device will send a clear event report to the controller. Unit: Second. Default 30 seconds This parameter is configured the light intensity threshold. When Ambient light intensity is less than this setting, device will consider the current environment is insufficient light. If "Configuration No. 3" is set '1' and a motion event is detected, the device will send a BASIC_SET to the nodes which associated in Group 2. Unit: 1 Lux. Available settings: 0 - 1000. Default: 50 This parameter is configured the light intensity threshold. When Ambient light intensity is less than this setting, device will consider the current environment is insufficient light. If "Configuration No. 3" is set '1' and a motion event is detected, the device will send a BASIC_SET to the nodes which associated in Group 2. Unit: 1 Lux. Available settings: 0 - 1000. Default: 50 Default: 180 This parameter is configured the time interval for light sensor, temperature and humidity sensor measuring. This value is larger, the battery life is longer. And the sensors values changed are not obvious. 0 - All sensors are disabled. Unit: Second. Available settings: 0 - 30000. Default: 180 (on batteries) or 10 (on USB) This parameter defines the calibrated scale for ambient light intensity. Because the method and position that the sensor mounted and the cover of sensor will bring measurement error, user can get more real light intensity by this parameter setting. User should run the steps blows for calibrating. 1. Set this parameter value to default (Assumes the sensor has been added in a Z-Wave Network). 2. Place a digital luxmeter close to sensor and keep the same direction, monitor the light intensity values (Vm) which report to controller and record it. The same time user should record the Value (Vs) of luxmeter. 3. The scale calibration formula: k = Vm / Vs. 4. The value of k is then multiplied by 1000 and rounded to the nearest whole number. 5. Set the value getting in 5) to this parameter, calibrate finished. For example, Vm = 300, Vs = 2000 [sic], then k = 300 / 2600 = 0.11538 k = 0.11538 * 1000 = 115,38 ~ 115 The parameter should be set to 115. Available settings: 1 ... 32767. Default: 5320 5 in 1 sensor: motion, temperat
'1' - Enable sensor binary report when device detects a motion event. '0' - Disable sensor binary report when device detects a motion event. Default: Disable This parameter is configured the time to clear motion event after a motion event detected. Time to motion clear, the device will send a clear event report to controller. Unit: Second. Available settings: 0 ... 30000. Default: 30 Zwave Smart Plug. The Device supports metering functions (voltage, current, energy consumption and power). It also supports thermostat's Heat mode, Energy Heat mode, OFF mode. The device cannot act as as network controller (primary or secondary) and wil allways need a Z-Wave network controller to be included into a Z-Wave network. (Note: When using S2 encryption mode to include the device, an encrypted key will need to be generated. The LED indicator may not flash, please wait and do not unplug the device.) There are two exclusion methods: Method l : Exclusion from the primary controller as follows: There are 3 methods for the smart plug to exit out of “exclusion mode". Once it exits “exclusion mode", the LED light will stop the fast fade-in and fade-out. Method 2: A "Factory reset" of the smart plug will force the device to be excluded from a network (please refer to the part “Factory Reset” of this manual). (Note: A "Factory reset" is not recommended for exclusion. Please use this procedure only if the primary controller is missing or otherwise inoperable.) Factory Reset: Press and hold the action button for over 10 seconds, the LED indicator should stay solid white for 3 seconds to indicate successfull factory reset. Release the action button, the smart plug will restart automatically. If the LED indicator flashes yellow slowly, the device was not included to any network in the first place. Heatit ZM Single Relay is a high power relay for in-wall installations. The relay allows you to control connected devices either through your Z-Wave network or via a wired switch. The module is equipped with a 16A relay and has a scene controller functionality. The Heatit ZM Single Relay has a power metering feature that allows you to monitor the power consumption of your connected devices. Supports encryption modes S0, S2 Authenticated Class, S2 Unauthenticated Class When the device has been included in the home automation system, the LED will stay green for 3 seconds. The device is now ready for use with default settings. When the device has been included in the home automation system, the LED will stay green for 3 seconds. The device is now ready for use with default settings. Heatit ZM Single Relay is a high power relay for in-wall installations. The relay allows you to control connected devices either through your Z-Wave network or via a wired switch. The module is equipped with a 16A relay and has a scene controller functionality. The Heatit ZM Single Relay has a power metering feature that allows you to monitor the power consumption of your connected devices. Supports encryption modes S0, S2 Authenticated Class, S2 Unauthenticated Class When the device has been included in the home automation system, the LED will stay green for 3 seconds. The device is now ready for use with default settings. When the device has been included in the home automation system, the LED will stay green for 3 seconds. The device is now ready for use with default settings. Heatit ZM Single Relay is a hig
Set the brightness level (default 20%) the dimmer will turn on to when off and when lower paddle is held DOWN for a second. Enable or disable scene control functionality for quick double tap triggers on the dimmer paddles. Enable (default) or disable scene control functionality for quick double tap triggers on the dimmer paddles. Enable or disable scene control functionality for quick double tap triggers on the relay button. Enable (default) or disable scene control functionality for quick double tap triggers on the relay button. Z-Wave dimmer paddle switch, 700 se
Choose if you want the LED indicator to turn on when the switch (light) is on or off, or if you want it to remain on or off at all times. NOTE: tap the upper paddle 6 times quickly to change this mode. Choose if you want the LED indicator to turn on when the switch (light) is on or off, or if you want it to remain on or off at all times. NOTE: tap the upper paddle 6 times quickly to change this mode.
Overview
+ Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Inclusion Information
Exclusion Information
Wakeup Information
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview
Overview