58 lines
2.9 KiB
JSON
58 lines
2.9 KiB
JSON
{
|
|
"config": {
|
|
"step": {
|
|
"user": {
|
|
"menu_options": {
|
|
"nibegw": "NibeGW",
|
|
"modbus": "Modbus"
|
|
},
|
|
"description": "Pick the connection method to your pump. In general, F-series pumps require a NibeGW custom accessory, while an S-series pump has Modbus support built-in."
|
|
},
|
|
"modbus": {
|
|
"data": {
|
|
"model": "Model of heat pump",
|
|
"modbus_url": "Modbus URL",
|
|
"modbus_unit": "Modbus unit identifier"
|
|
},
|
|
"data_description": {
|
|
"modbus_url": "Modbus URL that describes the connection to your heat pump or MODBUS40 unit. It should be in the form:\n - `tcp://[HOST]:[PORT]` for Modbus TCP connection\n - `serial://[LOCAL DEVICE]` for a local Modbus RTU connection\n - `rfc2217://[HOST]:[PORT]` for a remote Telnet-based Modbus RTU connection.",
|
|
"modbus_unit": "Unit identification for your heat pump. Can usually be left at 0."
|
|
}
|
|
},
|
|
"nibegw": {
|
|
"description": "Before attempting to configure the integration, verify that:\n - The NibeGW unit is connected to a heat pump.\n - The MODBUS40 accessory has been enabled in the heat pump configuration.\n - The pump has not gone into an alarm state about missing MODBUS40 accessory.",
|
|
"data": {
|
|
"model": "[%key:component::nibe_heatpump::config::step::modbus::data::model%]",
|
|
"ip_address": "Remote address",
|
|
"remote_read_port": "Remote read port",
|
|
"remote_write_port": "Remote write port",
|
|
"listening_port": "Local listening port"
|
|
},
|
|
"data_description": {
|
|
"ip_address": "The address of the NibeGW unit. The device should have been configured with a static address.",
|
|
"remote_read_port": "The port the NibeGW unit is listening for read requests on.",
|
|
"remote_write_port": "The port the NibeGW unit is listening for write requests on.",
|
|
"listening_port": "The local port on this system, that the NibeGW unit is configured to send data to."
|
|
}
|
|
}
|
|
},
|
|
"error": {
|
|
"write": "Error on write request to pump. Verify your `Remote write port` or `Remote address`.",
|
|
"read": "Error on read request from pump. Verify your `Remote read port` or `Remote address`.",
|
|
"address": "Invalid remote address specified. Address must be an IP address or a resolvable hostname.",
|
|
"address_in_use": "The selected listening port is already in use on this system.",
|
|
"model": "The selected model doesn't seem to support MODBUS40",
|
|
"unknown": "[%key:common::config_flow::error::unknown%]",
|
|
"url": "The specified URL is not well formed nor supported"
|
|
}
|
|
},
|
|
"exceptions": {
|
|
"write_timeout": {
|
|
"message": "Timeout while writing coil {address}"
|
|
},
|
|
"write_failed": {
|
|
"message": "Writing of coil {address} with value `{value}` failed with error `{error}`"
|
|
}
|
|
}
|
|
}
|